When posting something on this list, can you please at least show the decency and courtesy to...:
1. NOT compose you new message by replying to a message in an unrelated thread. 2. NOT include the whole content of the unrelated message when it clearly has no relevance to you post, not to mention it is almost twice longer than you question. 3. Post your question to the relevant mailing list, which is users in this case, as you question has nothing related to openser development. On Friday 30 May 2008, Steven Wu wrote: > Hi all, > > Does openser support long session (183 - PRACK)? > Currently the openser reply my ua with 404 when ua set PRACK to it. > > The flowing of SIP message like this > > > A openser > B > > | INVITE (with 100rel) -> | INVITE (with 100rel) | > | > | 183 <-- | 183 > | <-- | > | > | PRACK --> | > | 404 <--- | > > For support the PRACK, do I need do some configure in openser.cfg? > > > > > > > Best regards, > Steven Wu > > ________________________________ > > From: [EMAIL PROTECTED] 代表 Edson > Sent: 2008-5-29 (星期四) 21:51 > To: 'Anatoly Pidruchny'; 'Juha Heinanen'; devel@lists.openser.org > Subject: Re: [OpenSER-Devel] changing debug level on the fly > > > > Hey, this are good news... I'll give it a try... ;) > > Edson > > >-----Original Message----- > >From: [EMAIL PROTECTED] [mailto:devel- > >[EMAIL PROTECTED] On Behalf Of Anatoly Pidruchny > >Sent: quinta-feira, 29 de maio de 2008 09:35 > >To: Juha Heinanen; devel@lists.openser.org > >Subject: Re: [OpenSER-Devel] changing debug level on the fly > > > >Juha, > > > >you can also change the debug level temporarily per process for a > > script section using the script function setdebug. Below is some > > information from the ChangeLog for 1.3.x release. This function is > > still not documented in the core cookbook. > > > >2007-07-19 08:23 Bogdan-Andrei Iancu, <bogdan at voice-system dot ro> > > > > * [r2478] action.c, cfg.lex, cfg.y, dprint.c, dprint.h, route.c, > > route_struct.c, route_struct.h: > > - new core script function - setdebug([leve]) - it can be used > > to change the debug level (per process) for a script section. > > > >-- > >Anatoly. > > > >> Edson writes: > >> > It would be even better if this control could be done not only > >> > through > > > >MI > > > >> > commands, but also through script commands/variable. It would > >> > permit increase and decrease debug level based on script logic > >> > given a more granular control over debug info. > >> > >> that should be possible if debug variable would be mapped to a > >> shared memory variable that could then be set using cfgutils > >> functions. > >> > >> -- juha > >> > >> _______________________________________________ > >> Devel mailing list > >> Devel@lists.openser.org > >> http://lists.openser.org/cgi-bin/mailman/listinfo/devel > > > >_______________________________________________ > >Devel mailing list > >Devel@lists.openser.org > >http://lists.openser.org/cgi-bin/mailman/listinfo/devel > > _______________________________________________ > Devel mailing list > Devel@lists.openser.org > http://lists.openser.org/cgi-bin/mailman/listinfo/devel -- Dan _______________________________________________ Devel mailing list Devel@lists.openser.org http://lists.openser.org/cgi-bin/mailman/listinfo/devel
