Hello Adolf, There should actually be some improvement on the Prime and the Duo Appliances at least.
They had some problems when the HDMI port got disconnected from one screen while it was running and connected to another one. Or booted without anything plugged into HDMI and then something got plugged in. They simply could not switch any resolution because of some limitations in the Intel GPU driver. DRM should now support this. I have not tested this, but I strongly hope it does. -Michael > On 16 Jun 2025, at 12:28, Adolf Belka <[email protected]> wrote: > > Hi Michael, > > On 16/06/2025 10:52, Michael Tremer wrote: >> Good morning Adolf, >> The DRM feedback is very valuable. I don’t think we should be breaking >> anything, but it would be important to get as much information in as soon as >> possible. > > To help with that I have also tested out CU196 Unstable on my Prime physical > system. > > Everything worked as normal. No problems at all. > > In this case the size of the console did not change as it was already taking > the whole height of my widescreen monitor with CU195 Testing. > > Regards, > > Adolf. > >> -Michael >>> On 15 Jun 2025, at 19:53, Adolf Belka <[email protected]> wrote: >>> >>> Hi Michael, >>> >>> I just did a test of suricata-8.0.0-rc1 in a 196 build so was also able to >>> test out this patch set for DRM. >>> >>> My vm console terminal worked and was shown at a higher resolution than >>> previously. >>> >>> So everything worked fine from my simple test. >>> >>> Regards, >>> >>> Adolf. >>> >>> >>> On 27/04/2025 19:15, Michael Tremer wrote: >>>> Signed-off-by: Michael Tremer <[email protected]> >>>> --- >>>> config/rootfiles/common/aarch64/linux | 1 - >>>> config/rootfiles/common/riscv64/linux | 1 - >>>> config/rootfiles/common/x86_64/linux | 1 - >>>> lfs/linux | 13 ------------- >>>> 4 files changed, 16 deletions(-) >>>> diff --git a/config/rootfiles/common/aarch64/linux >>>> b/config/rootfiles/common/aarch64/linux >>>> index 88c528557..ffd22d7a8 100644 >>>> --- a/config/rootfiles/common/aarch64/linux >>>> +++ b/config/rootfiles/common/aarch64/linux >>>> @@ -573,7 +573,6 @@ boot/dtb-KVER >>>> #boot/dtb-KVER/synaptics/berlin4ct-stb.dtb >>>> boot/vmlinuz-KVER >>>> #etc/cpufreq-bench.conf >>>> -etc/modprobe.d/framebuffer.conf >>>> etc/modprobe.d/ipv6.conf >>>> #lib/modules >>>> #lib/modules/KVER >>>> diff --git a/config/rootfiles/common/riscv64/linux >>>> b/config/rootfiles/common/riscv64/linux >>>> index e1b6c071c..7681cf09a 100644 >>>> --- a/config/rootfiles/common/riscv64/linux >>>> +++ b/config/rootfiles/common/riscv64/linux >>>> @@ -13,7 +13,6 @@ boot/dtb-KVER >>>> #boot/dtb-KVER/starfive/jh7110-starfive-visionfive-2-v1.3b.dtb >>>> boot/vmlinuz-KVER >>>> #etc/cpufreq-bench.conf >>>> -etc/modprobe.d/framebuffer.conf >>>> etc/modprobe.d/ipv6.conf >>>> #lib/modules >>>> #lib/modules/KVER >>>> diff --git a/config/rootfiles/common/x86_64/linux >>>> b/config/rootfiles/common/x86_64/linux >>>> index aeb8ce71b..7ae6bbaae 100644 >>>> --- a/config/rootfiles/common/x86_64/linux >>>> +++ b/config/rootfiles/common/x86_64/linux >>>> @@ -2,7 +2,6 @@ boot/System.map-KVER >>>> boot/config-KVER >>>> boot/vmlinuz-KVER >>>> #etc/cpufreq-bench.conf >>>> -etc/modprobe.d/framebuffer.conf >>>> etc/modprobe.d/ipv6.conf >>>> #lib/modules >>>> #lib/modules/KVER >>>> diff --git a/lfs/linux b/lfs/linux >>>> index f1a436c03..15e279ca9 100644 >>>> --- a/lfs/linux >>>> +++ b/lfs/linux >>>> @@ -225,19 +225,6 @@ endif >>>> # Only do this once >>>> cd $(DIR_APP) && install -m 755 usr/gen_init_cpio /sbin/ >>>> - # disable drm by install drm to /bin/false because i915 ignore >>>> blacklisting >>>> - echo install drm /bin/false > /etc/modprobe.d/framebuffer.conf >>>> - >>>> - # Blacklist old framebuffer modules >>>> - for f in $$(find /lib/modules/$(KVER)/kernel/drivers/video/fbdev/ -name >>>> *.ko.xz); do \ >>>> - echo "blacklist $$(basename $$f)" >> /etc/modprobe.d/framebuffer.conf ; \ >>>> - done >>>> - # Blacklist new drm framebuffer modules >>>> - for f in $$(find /lib/modules/$(KVER)/kernel/drivers/gpu/drm -name >>>> *.ko.xz); do \ >>>> - echo "blacklist $$(basename $$f)" >> /etc/modprobe.d/framebuffer.conf ; \ >>>> - done >>>> - sed -i -e "s|.ko.xz||g" /etc/modprobe.d/framebuffer.conf >>>> - >>>> # Disable ipv6 at runtime >>>> echo "options ipv6 disable_ipv6=1" > /etc/modprobe.d/ipv6.conf >>>> >>> >>> >
