Hi Florian, Le 16/03/2013 15:41, Florian Fainelli a écrit : > Hello Maxime, Stefan, > > Please find below some comments regarding your PHY implementation in the > driver > as well as the transmit and transmit completion routines.
Stefan implemented the changes you asked about the PHY, it will be in the next iteration of this patchset. On a general basis, we don't really know much about this chip, since we're working without any datasheet on this. > >> +#define WEMAC_PHY 0x100 /* PHY address 0x01 */ > > This should be made configurable if possible. Ok >> + unsigned power_gpio; > > you could make this an int, so that you use gpio_is_valid() on this one. Alexander Shiyan suggested to move to the regulator API, so I guess we will just remove that variable. >> + >> +static void wemac_dumpblk_32bit(void __iomem *reg, int count) >> +{ >> + int i; >> + int tmp; >> + >> + for (i = 0; i < (round_up(count, 4) / 4); i++) >> + tmp = readl(reg); >> +} > > This could probably be removed, tmp is a write only location, did you remove > the variable printing that came along this? Hmmm, it looks that way yes. I'll remove it >> + >> +static int wemac_ioctl(struct net_device *dev, struct ifreq *req, int cmd) >> +{ >> + struct wemac_board_info *dm = to_wemac_board(dev); >> + >> + if (!netif_running(dev)) >> + return -EINVAL; >> + >> + return generic_mii_ioctl(&dm->mii, if_mii(req), cmd, NULL); >> +} >> + >> +/* ethtool ops */ >> +static void wemac_get_drvinfo(struct net_device *dev, >> + struct ethtool_drvinfo *info) >> +{ >> + strcpy(info->driver, DRV_NAME); >> + strcpy(info->version, DRV_VERSION); > > You should use strlcpy() here to ensure null-termination, and you should also > fill in the bus_info member of struct ethtool_drvinfo. ok, will do. >> + /* Init Driver variable */ >> + db->tx_fifo_stat = 0; >> + dev->trans_start = 0; > > I do not think this is required you are supposed to update this field only in > the receive path. Ok, I'll remove that part. >> + >> + channel = (channel == 1 ? 1 : 0); >> + >> + spin_lock_irqsave(&db->lock, flags); >> + >> + writel(channel, db->membase + EMAC_TX_INS_REG); >> + >> + wemac_outblk_32bit(db->membase + EMAC_TX_IO_DATA_REG, >> + skb->data, skb->len); >> + dev->stats.tx_bytes += skb->len; >> + >> + db->tx_fifo_stat |= 1 << channel; >> + /* TX control: First packet immediately send, second packet queue */ >> + if (channel == 0) { >> + /* set TX len */ >> + writel(skb->len, db->membase + EMAC_TX_PL0_REG); >> + /* start translate from fifo to phy */ >> + writel(readl(db->membase + EMAC_TX_CTL0_REG) | 1, >> + db->membase + EMAC_TX_CTL0_REG); > > Do not you need some write barrier here to ensure your descriptor address and > control are properly written before the EMAC will see these? writel has a write barrier, so it shouldn't be a problem I guess. > >> + >> + /* save the time stamp */ >> + dev->trans_start = jiffies; >> + } else if (channel == 1) { >> + /* set TX len */ >> + writel(skb->len, db->membase + EMAC_TX_PL1_REG); >> + /* start translate from fifo to phy */ >> + writel(readl(db->membase + EMAC_TX_CTL1_REG) | 1, >> + db->membase + EMAC_TX_CTL1_REG); >> + >> + /* save the time stamp */ >> + dev->trans_start = jiffies; >> + } >> + >> + if ((db->tx_fifo_stat & 3) == 3) { >> + /* Second packet */ >> + netif_stop_queue(dev); > > Why is that required? Does that mean that your EMAC can only transmit one > packet at a time? The original driver was working that way, so the hardware can probably send several packet at a time, but we don't really know how... >> +static void wemac_tx_done(struct net_device *dev, struct wemac_board_info >> *db, + unsigned int tx_status) >> +{ >> + /* One packet sent complete */ >> + db->tx_fifo_stat &= ~(tx_status & 3); >> + if (3 == (tx_status & 3)) >> + dev->stats.tx_packets += 2; >> + else >> + dev->stats.tx_packets++; >> + >> + if (netif_msg_tx_done(db)) >> + dev_dbg(db->dev, "tx done, NSR %02x\n", tx_status); >> + >> + netif_wake_queue(dev); > > Why is that also required? According to your start_xmit function you should > do > this only when you have transmitted 2 packets no? I don't know, maybe the code here is more about always having a buffer of one packet at any point in time. With the current code, when you have to send packets, it will: - send the packet 1 - stop the queue - wait for the packet 1 to be sent - once packet 1 is sent, restart the queue, so that it can load a packet 3 - start transmitting packet 2 if there's one, and loop, or just wait for it Which would make sense, and for this, it looks to me that you should always restart the queue, no matter what the number of packets to send was. >> + >> + reg_val = readl(db->membase + EMAC_RX_IO_DATA_REG); >> + if (netif_msg_rx_status(db)) >> + dev_dbg(db->dev, "receive header: %x\n", reg_val); >> + if (reg_val != 0x0143414d) { > > Where is that magic value coming from? The original code. Maybe I should define it to something like "UNDOCUMENTED_VOODOO_MAGIC1", or something like that, but I have no idea what it relates to in the hardware :S Thanks for your review, Maxime -- Maxime Ripard, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com _______________________________________________ devicetree-discuss mailing list devicetree-discuss@lists.ozlabs.org https://lists.ozlabs.org/listinfo/devicetree-discuss