On Wed, 12 Jun 2013 00:03:57 +0200, Laurent Pinchart
<laurent.pinchart+rene...@ideasonboard.com> wrote:
> Document DT properties for the generic pinctrl parameters and add a
> parser function.
>
> Signed-off-by: Laurent Pinchart <laurent.pinchart+rene...@ideasonboard.com>
> ---
> .../bindings/pinctrl/pinctrl-bindings.txt | 29 +++++++
> drivers/pinctrl/pinconf-generic.c | 94
> ++++++++++++++++++++++
> drivers/pinctrl/pinconf.h | 17 ++++
> 3 files changed, 140 insertions(+)
>
> I've successfully tested this patch (or more accurately only the pull-up and
> pull-down properties) with the Renesas sh-pfc pinctrl device driver. I will
> resent the sh-pfc DT bindings patch series rebased on the generic pinconf
> bindings.
>
> Not all generic pinconf properties are currently implemented, but I don't
> think that should be a showstopper. We can add them later as needed.
>
> The code is based on both the sh-pfc pinconf DT parser and James Hogan's
> tz1090 DT parser ("[PATCH v2 6/9] pinctrl-tz1090: add TZ1090 pinctrl driver").
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
> b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
> index c95ea82..e499ff0 100644
> --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
> +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
> @@ -126,3 +126,32 @@ device; they may be grandchildren, for example. Whether
> this is legal, and
> whether there is any interaction between the child and intermediate parent
> nodes, is again defined entirely by the binding for the individual pin
> controller device.
> +
> +== Generic pinconf parameters ==
> +
> +Pin configuration parameters are expressed by DT properties in the pin
> +controller device state nodes and child nodes. For devices that use the
> generic
> +pinconf parameters the following properties are defined.
> +
> +- tristate: A boolean, put the pin into high impedance state when set.
> +
> +- pull-up: An integer representing the pull-up strength. 0 disables the
> pull-up,
> + non-zero values enable it.
> +
> +- pull-down: An integer representing the pull-down strength. 0 disables the
> + pull-down, non-zero values enables it.
> +
> +- schmitt: An integer, enable or disable Schmitt trigger mode for the pins.
> + Valid values are
> + 0: Schmitt trigger disabled (no hysteresis)
> + 1: Schmitt trigger enabled
> +
> +- slew-rate: An integer controlling the pin slew rate. Values are device-
> + dependent.
> +
> +- drive-strength: An integer representing the drive strength of pins in mA.
> + Valid values are device-dependent.
> +
> +The pinctrl device DT bindings documentation must list the properties that
> +apply to the device, and define the valid range for all device-dependent
> +values.
I don't see any problem with the above properties, but I would like to
see an example. How verbose will a pinctrl node using the generic
properties tend to be?
> diff --git a/drivers/pinctrl/pinconf-generic.c
> b/drivers/pinctrl/pinconf-generic.c
> index 2ad5a8d..bd0e41d 100644
> --- a/drivers/pinctrl/pinconf-generic.c
> +++ b/drivers/pinctrl/pinconf-generic.c
> @@ -15,6 +15,7 @@
> #include <linux/module.h>
> #include <linux/init.h>
> #include <linux/device.h>
> +#include <linux/of.h>
> #include <linux/slab.h>
> #include <linux/debugfs.h>
> #include <linux/seq_file.h>
> @@ -135,3 +136,96 @@ void pinconf_generic_dump_config(struct pinctrl_dev
> *pctldev,
> }
> EXPORT_SYMBOL_GPL(pinconf_generic_dump_config);
> #endif
> +
> +struct pinconf_generic_param {
> + const char *property;
> + enum pin_config_param param;
> + bool flag;
> +};
> +
> +static const struct pinconf_generic_param pinconf_generic_params[] = {
> + { "tristate", PIN_CONFIG_BIAS_HIGH_IMPEDANCE, true },
> + { "pull-up", PIN_CONFIG_BIAS_PULL_UP, false },
> + { "pull-down", PIN_CONFIG_BIAS_PULL_DOWN, false },
> + { "schmitt", PIN_CONFIG_INPUT_SCHMITT_ENABLE, true },
> + { "slew-rate", PIN_CONFIG_SLEW_RATE, false },
> + { "drive-strength", PIN_CONFIG_DRIVE_STRENGTH, false },
> +};
> +
> +static int pinconf_generic_add_config(unsigned long **configs,
> + unsigned int *num_configs,
> + unsigned long config)
> +{
> + unsigned int count = *num_configs + 1;
> + unsigned long *cfgs;
> +
> + cfgs = krealloc(*configs, sizeof(*cfgs) * count, GFP_KERNEL);
> + if (cfgs == NULL)
> + return -ENOMEM;
> +
> + cfgs[count - 1] = config;
> +
> + *configs = cfgs;
> + *num_configs = count;
> +
> + return 0;
> +}
Hmmm. We really need a better method of parsing multiple properties.
I've been toying around with a few ideas, but haven't been able to draft
something I'm happy with yeat.
Regardless, the code in this patch looks fine to me.
g.
_______________________________________________
devicetree-discuss mailing list
devicetree-discuss@lists.ozlabs.org
https://lists.ozlabs.org/listinfo/devicetree-discuss
