On Mon, Nov 25, 2013 at 10:02:30PM -0700, Stephen Warren wrote:
> The DWC2 USB controller in the BCM2835 (Raspberry Pi) needs some non-
> default parameters. Select these based on the compatible value from the
> DT node. For all other HW, fall back to the default parameters currently
> in use.
>
> The values in params_bcm2835[] were posted to the mailing list by Paul
> quite some time ago. I made a couple of minor modifications since then;
> to set ahbcfg instead of ahb_single, and to set uframe_sched.
>
> Signed-off-by: Stephen Warren <swar...@wwwdotorg.org>
> ---
> Documentation/devicetree/bindings/staging/dwc2.txt | 4 +-
> drivers/staging/dwc2/platform.c | 56
> ++++++++++++++++----
> 2 files changed, 50 insertions(+), 10 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/staging/dwc2.txt
> b/Documentation/devicetree/bindings/staging/dwc2.txt
> index 1a1b7cf..8b60e90 100644
> --- a/Documentation/devicetree/bindings/staging/dwc2.txt
> +++ b/Documentation/devicetree/bindings/staging/dwc2.txt
> @@ -2,7 +2,9 @@ Platform DesignWare HS OTG USB 2.0 controller
> -----------------------------------------------------
>
> Required properties:
> -- compatible : "snps,dwc2"
> +- compatible : One of:
> + - brcm,bcm2835-usb: The DWC2 USB controller instance in the BCM2835 SoC.
> + - snps,dwc2: A generic DWC2 USB controller with default parameters.
> - reg : Should contain 1 register range (address and length)
> - interrupts : Should contain 1 interrupt
>
> diff --git a/drivers/staging/dwc2/platform.c b/drivers/staging/dwc2/platform.c
> index 4d9fac0..20586dc 100644
> --- a/drivers/staging/dwc2/platform.c
> +++ b/drivers/staging/dwc2/platform.c
> @@ -39,6 +39,7 @@
> #include <linux/slab.h>
> #include <linux/device.h>
> #include <linux/dma-mapping.h>
> +#include <linux/of_device.h>
> #include <linux/platform_device.h>
>
> #include "core.h"
> @@ -46,6 +47,33 @@
>
> static const char dwc2_driver_name[] = "dwc2";
>
> +static const struct dwc2_core_params params_bcm2835 = {
> + .otg_cap = 0, /* HNP/SRP capable */
> + .otg_ver = 0, /* 1.3 */
> + .dma_enable = 1,
> + .dma_desc_enable = 0,
> + .speed = 0, /* High Speed */
> + .enable_dynamic_fifo = 1,
> + .en_multiple_tx_fifo = 1,
> + .host_rx_fifo_size = 774, /* 774 DWORDs */
> + .host_nperio_tx_fifo_size = 256, /* 256 DWORDs */
> + .host_perio_tx_fifo_size = 512, /* 512 DWORDs */
> + .max_transfer_size = 65535,
> + .max_packet_count = 511,
> + .host_channels = 8,
> + .phy_type = 1, /* UTMI */
> + .phy_utmi_width = 8, /* 8 bits */
> + .phy_ulpi_ddr = 0, /* Single */
> + .phy_ulpi_ext_vbus = 0,
> + .i2c_enable = 0,
> + .ulpi_fs_ls = 0,
> + .host_support_fs_ls_low_power = 0,
> + .host_ls_low_power_phy_clk = 0, /* 48 MHz */
> + .ts_dline = 0,
> + .reload_ctl = 0,
> + .ahbcfg = 0x10,
> +};
> +
> /**
> * dwc2_driver_remove() - Called when the DWC_otg core is unregistered with
> the
> * DWC_otg driver
> @@ -66,6 +94,13 @@ static int dwc2_driver_remove(struct platform_device *dev)
> return 0;
> }
>
> +static const struct of_device_id dwc2_of_match_table[] = {
> + { .compatible = "brcm,bcm2835-usb", .data = ¶ms_bcm2835 },
> + { .compatible = "snps,dwc2", .data = NULL },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, dwc2_of_match_table);
> +
> /**
> * dwc2_driver_probe() - Called when the DWC_otg core is bound to the DWC_otg
> * driver
> @@ -80,14 +115,23 @@ static int dwc2_driver_remove(struct platform_device
> *dev)
> */
> static int dwc2_driver_probe(struct platform_device *dev)
> {
> + const struct of_device_id *match;
> + const struct dwc2_core_params *params;
> + struct dwc2_core_params defparams;
> struct dwc2_hsotg *hsotg;
> struct resource *res;
> int retval;
> int irq;
> - struct dwc2_core_params params;
> +
> + match = of_match_device(dwc2_of_match_table, &dev->dev);
> + if (match)
> + params = match->data;
> + else {
> + dwc2_set_all_params(&defparams, -1);
> + params = &defparams;
> + }
If that matches "snps,dwc2", params will be NULL instead of the default set,
which I guess was not your intention?
>
> /* Default all params to autodetect */
> - dwc2_set_all_params(¶ms, -1);
The comment can be moved too.
>
> hsotg = devm_kzalloc(&dev->dev, sizeof(*hsotg), GFP_KERNEL);
> if (!hsotg)
> @@ -118,7 +162,7 @@ static int dwc2_driver_probe(struct platform_device *dev)
> dev_dbg(&dev->dev, "mapped PA %08lx to VA %p\n",
> (unsigned long)res->start, hsotg->regs);
>
> - retval = dwc2_hcd_init(hsotg, irq, ¶ms);
> + retval = dwc2_hcd_init(hsotg, irq, params);
> if (retval)
> return retval;
>
> @@ -127,12 +171,6 @@ static int dwc2_driver_probe(struct platform_device *dev)
> return retval;
> }
>
> -static const struct of_device_id dwc2_of_match_table[] = {
> - { .compatible = "snps,dwc2" },
> - {},
> -};
> -MODULE_DEVICE_TABLE(of, dwc2_of_match_table);
> -
> static struct platform_driver dwc2_platform_driver = {
> .driver = {
> .name = dwc2_driver_name,
> --
> 1.7.10.4
>
> _______________________________________________
> devel mailing list
> de...@linuxdriverproject.org
> http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
