On 1/10/14 2:00 PM, Steffen Trumtrar wrote:
> Hi!
>
> On Fri, Jan 10, 2014 at 10:49:59AM -0600, Vince Bridgers wrote:
>> This change adds a parameter for the Synopsys 10/100/1000
>> stmmac Ethernet driver to configure the maximum MTU supported
>> by the EMAC instance. Synopsys allows the FIFO sizes to
>> be configured when the cores are built for a particular
>> device, but do not provide a way for the driver to read
>> information from the device about the maximum MTU size
>> supported as limited by the device's FIFO size.
>>
>> This patch has been tested with changes being submitted
>> seperately for the Synopsys 10/100/1000 stmmac driver.
>>
>> Signed-off-by: Vince Bridgers <vbridgers2...@gmail.com>
>> ---
>> Documentation/devicetree/bindings/net/stmmac.txt | 5 +++++
>> arch/arm/boot/dts/socfpga_cyclone5.dtsi | 19 +++++++++++++++++++
>> 2 files changed, 24 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/net/stmmac.txt
>> b/Documentation/devicetree/bindings/net/stmmac.txt
>> index eba0e5e..7db314e 100644
>> --- a/Documentation/devicetree/bindings/net/stmmac.txt
>> +++ b/Documentation/devicetree/bindings/net/stmmac.txt
>> @@ -30,6 +30,10 @@ Required properties:
>>
>> Optional properties:
>> - mac-address: 6 bytes, mac address
>> +- snps,max-mtu: Maximum MTU permitted. This parameter is useful
>> since
>> + different implementations of the Synopsys MAC may have
>> + different FIFO sizes depending on the selections
>> + made in Synopsys Core Consultant.
>>
>> Examples:
>>
>> @@ -40,5 +44,6 @@ Examples:
>> interrupts = <24 23>;
>> interrupt-names = "macirq", "eth_wake_irq";
>> mac-address = [000000000000]; /* Filled in by U-Boot */
>> + snps,max-mtu = <3800>;
>> phy-mode = "gmii";
>> };
>> diff --git a/arch/arm/boot/dts/socfpga_cyclone5.dtsi
>> b/arch/arm/boot/dts/socfpga_cyclone5.dtsi
>> index a8716f6..b6b39dd 100644
>> --- a/arch/arm/boot/dts/socfpga_cyclone5.dtsi
>> +++ b/arch/arm/boot/dts/socfpga_cyclone5.dtsi
>> @@ -63,3 +63,22 @@
>> };
>> };
>> };
>> +
>> +&gmac1 {
>> + phy-mode = "rgmii";
>> + snps,phy-addr = <0xffffffff>; /* probe for phy addr */
>> +
>> + rxd0-skew-ps = <0>;
>> + rxd0-skew-ps = <0>;
>> + rxd1-skew-ps = <0>;
>> + rxd2-skew-ps = <0>;
>> + rxd3-skew-ps = <0>;
>> + txen-skew-ps = <0>;
>> + txc-skew-ps = <2600>;
>> + rxdv-skew-ps = <0>;
>> + rxc-skew-ps = <2000>;
> This all seems to be unrelated to the patch description and there isn't even
> any binding documentatation (or is that in another patch ?).
The documentation for all of these properties are located in
micrel-ksz9021.txt.
But that's a moot point since this entry should be removed from this
patch anyways.
Also, this patch was not sent to any of the DTS bindings maintainers.
Dinh
> Additionally these don't seem to be properties that apply to all cyclone5
> based
> boards, so they don't belong here.
>
>> + snps,max-mtu = <3800>;
>> + altr,sysmgr-phy-mask = <0xC>;
>> + status = "okay";
> ^^^^
> At least this is only valid for boards that use gmac1.
> Put this in a boardspecific DT.
>
> Regards,
> Steffen
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
