Hi Ash, On 06/06/2014 10:51 PM, Ash Charles wrote: > This adds the Gumstix Pepper[1] single-board computer based on the > TI AM335x processor. Schematics are available [2]. > > [1] https://store.gumstix.com/index.php/products/344/ > [2] https://pubs.gumstix.com/boards/PEPPER/ > > Signed-off-by: Ash Charles <ashchar...@gmail.com> > --- > MAINTAINERS | 6 + > arch/arm/boot/dts/Makefile | 3 +- > arch/arm/boot/dts/am335x-pepper.dts | 661 > ++++++++++++++++++++++++++++++++++++ > 3 files changed, 669 insertions(+), 1 deletion(-) > create mode 100644 arch/arm/boot/dts/am335x-pepper.dts > > diff --git a/MAINTAINERS b/MAINTAINERS > index 51ebb77..d44e2e3 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -6427,6 +6427,12 @@ L: linux-o...@vger.kernel.org > S: Maintained > F: arch/arm/boot/dts/am335x-nano.dts > > +OMAP/GUMSTIX PEPPER MACHINE SUPPORT > +M: Ash Charles <ashchar...@gmail.com> > +L: linux-o...@vger.kernel.org > +S: Maintained > +F: arch/arm/boot/dts/am335x-pepper.dts > +
It is not very common to add oneself as the maintainer of a single .dts file. I could only found the am335x-nano.dts with such a way of doing. Usually get_maintainer.pl will also take into account the commit author and properly handle this case. > OMFS FILESYSTEM > M: Bob Copeland <m...@bobcopeland.com> > L: linux-karma-de...@lists.sourceforge.net > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index a81a24c..9e0352f 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -277,7 +277,8 @@ dtb-$(CONFIG_SOC_AM33XX) += am335x-base0033.dtb \ > am335x-boneblack.dtb \ > am335x-evm.dtb \ > am335x-evmsk.dtb \ > - am335x-nano.dtb > + am335x-nano.dtb \ > + am335x-pepper.dtb > dtb-$(CONFIG_ARCH_OMAP4) += omap4-duovero-parlor.dtb \ > omap4-panda.dtb \ > omap4-panda-a4.dtb \ > diff --git a/arch/arm/boot/dts/am335x-pepper.dts > b/arch/arm/boot/dts/am335x-pepper.dts > new file mode 100644 > index 0000000..27d9b75 > --- /dev/null > +++ b/arch/arm/boot/dts/am335x-pepper.dts > @@ -0,0 +1,661 @@ > +/* > + * Copyright (C) 2014 Gumstix, Inc. - https://www.gumstix.com/ > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > +/dts-v1/; > + > +#include "am33xx.dtsi" > + > +/ { > + model = "Gumstix Pepper"; > + compatible = "gumstix,am335x-pepper", "ti,am33xx"; > + > + cpus { > + cpu@0 { > + cpu0-supply = <&dcdc3_reg>; > + }; > + }; > + > + memory { > + device_type = "memory"; > + reg = <0x80000000 0x20000000>; /* 512 MB */ > + }; > + > + buttons: user_buttons { > + compatible = "gpio-keys"; > + }; > + For all the boards that I have seen, all the properties of a new node are declared at the same place, where you put some of them at the end. I have not a strong opinion on this, but I find it a bit more difficult to read. > + leds: user_leds { > + compatible = "gpio-leds"; > + }; > + > + panel: lcd_panel { > + compatible = "ti,tilcdc,panel"; > + }; > + > + sound: sound_iface { > + compatible = "ti,da830-evm-audio"; > + }; > + > + vbat: fixedregulator@0 { > + compatible = "regulator-fixed"; > + }; > + > + v3v3c_reg: fixedregulator@1 { > + compatible = "regulator-fixed"; > + }; > + > + vdd5_reg: fixedregulator@2 { > + compatible = "regulator-fixed"; > + }; > +}; > + > +/* I2C Busses */ > +&i2c0 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c0_pins>; > + > + clock-frequency = <400000>; > + > + tps: tps@24 { > + reg = <0x24>; > + }; > + > + eeprom: eeprom@50 { > + compatible = "at,24c256"; > + reg = <0x50>; > + }; > + > + audio_codec: tlv320aic3106@1b { > + compatible = "ti,tlv320aic3106"; > + reg = <0x1b>; > + }; > + > + accel: lis331dlh@1d { > + compatible = "st,lis3lv02d"; > + reg = <0x1d>; > + }; > +}; > + > +&i2c1 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c1_pins>; > + clock-frequency = <400000>; > +}; > + > +&am33xx_pinmux { > + i2c0_pins: pinmux_i2c0 { > + pinctrl-single,pins = < > + 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* > i2c0_sda.i2c0_sda */ > + 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* > i2c0_scl.i2c0_scl */ > + >; > + }; > + i2c1_pins: pinmux_i2c1 { > + pinctrl-single,pins = < > + 0x10C (PIN_INPUT_PULLUP | MUX_MODE3) /* > mii1_crs,i2c1_sda */ > + 0x110 (PIN_INPUT_PULLUP | MUX_MODE3) /* > mii1_rxerr,i2c1_scl */ > + >; > + }; > +}; > + Splitting the pinmux is also unusual, but in this case I found it more readable. > +/* Accelerometer */ > +&accel { > + pinctrl-names = "default"; > + pinctrl-0 = <&accel_pins>; > + > + Vdd-supply = <&ldo3_reg>; > + Vdd_IO-supply = <&ldo3_reg>; > + st,irq1-click; > + st,wakeup-x-lo; > + st,wakeup-x-hi; > + st,wakeup-y-lo; > + st,wakeup-y-hi; > + st,wakeup-z-lo; > + st,wakeup-z-hi; > + st,min-limit-x = <92>; > + st,max-limit-x = <14>; > + st,min-limit-y = <14>; > + st,max-limit-y = <92>; > + st,min-limit-z = <92>; > + st,max-limit-z = <14>; > +}; > + > +&am33xx_pinmux { > + accel_pins: pinmux_accel { > + pinctrl-single,pins = < > + 0x98 (PIN_INPUT_PULLUP | MUX_MODE7) /* > gpmc_wen.gpio2_4 */ The INT pin of the LIS33 chip seems to be push-pull, thus enabling the pullup on the SoC side will increase the current consumption when held down. > + >; > + }; > +}; > + > +/* Audio */ > +&audio_codec { > + status = "okay"; > + > + gpio-reset = <&gpio1 16 GPIO_ACTIVE_LOW>; > + AVDD-supply = <&ldo3_reg>; > + IOVDD-supply = <&ldo3_reg>; > + DRVDD-supply = <&ldo3_reg>; > + DVDD-supply = <&dcdc1_reg>; > +}; > + > +&sound { > + ti,model = "AM335x-EVM"; > + ti,audio-codec = <&audio_codec>; > + ti,mcasp-controller = <&mcasp0>; > + ti,codec-clock-rate = <12000000>; > + ti,audio-routing = > + "Headphone Jack", "HPLOUT", > + "Headphone Jack", "HPROUT", > + "LINE1L", "Line In"; > +}; > + > +&mcasp0 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&audio_pins>; > + > + op-mode = <0>; /* MCASP_ISS_MODE */ > + tdm-slots = <2>; > + serial-dir = < > + 1 2 0 0 > + 0 0 0 0 > + 0 0 0 0 > + 0 0 0 0 > + >; > + tx-num-evt = <1>; > + rx-num-evt = <1>; > +}; > + > +&am33xx_pinmux { > + audio_pins: pinmux_audio { > + pinctrl-single,pins = < > + 0x1AC (PIN_INPUT_PULLDOWN | MUX_MODE0) /* > mcasp0_ahcklx.mcasp0_ahclkx */ > + 0x194 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* > mcasp0_fsx.mcasp0_fsx */ > + 0x190 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* > mcasp0_aclkx.mcasp0_aclkx */ > + 0x198 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* > mcasp0_axr0.mcasp0_axr0 */ > + 0x1A8 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* > mcasp0_axr1.mcasp0_axr1 */ > + 0x40 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* > gpmc_a0.gpio1_16 */ You already have an external pullup in your design, so this one seems superfluous. > + >; > + }; > +}; > + > +/* Display: 24-bit LCD Screen */ > +&panel { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&lcd_pins>; > + panel-info { > + ac-bias = <255>; > + ac-bias-intrpt = <0>; > + dma-burst-sz = <16>; > + bpp = <32>; > + fdd = <0x80>; > + sync-edge = <0>; > + sync-ctrl = <1>; > + raster-order = <0>; > + fifo-th = <0>; > + }; > + display-timings { > + native-mode = <&timing0>; > + timing0: 480x272 { > + clock-frequency = <18400000>; > + hactive = <480>; > + vactive = <272>; > + hfront-porch = <8>; > + hback-porch = <4>; > + hsync-len = <41>; > + vfront-porch = <4>; > + vback-porch = <2>; > + vsync-len = <10>; > + hsync-active = <1>; > + vsync-active = <1>; > + }; > + }; > +}; > + > +&lcdc { > + status = "okay"; > +}; > + > +&am33xx_pinmux { > + lcd_pins: pinmux_lcd { > + pinctrl-single,pins = < > + 0xa0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 > */ > + 0xa4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 > */ > + 0xa8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 > */ > + 0xac (PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 > */ > + 0xb0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 > */ > + 0xb4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 > */ > + 0xb8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 > */ > + 0xbc (PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 > */ > + 0xc0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 > */ > + 0xc4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 > */ > + 0xc8 (PIN_OUTPUT | MUX_MODE0) /* > lcd_data10.lcd_data10 */ > + 0xcc (PIN_OUTPUT | MUX_MODE0) /* > lcd_data11.lcd_data11 */ > + 0xd0 (PIN_OUTPUT | MUX_MODE0) /* > lcd_data12.lcd_data12 */ > + 0xd4 (PIN_OUTPUT | MUX_MODE0) /* > lcd_data13.lcd_data13 */ > + 0xd8 (PIN_OUTPUT | MUX_MODE0) /* > lcd_data14.lcd_data14 */ > + 0xdc (PIN_OUTPUT | MUX_MODE0) /* > lcd_data15.lcd_data15 */ > + 0x20 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad8.lcd_data16 > */ > + 0x24 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad9.lcd_data17 > */ > + 0x28 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad10.lcd_data18 > */ > + 0x2c (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad11.lcd_data19 > */ > + 0x30 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad12.lcd_data20 > */ > + 0x34 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad13.lcd_data21 > */ > + 0x38 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad14.lcd_data22 > */ > + 0x3c (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad15.lcd_data23 > */ > + 0xe0 (PIN_OUTPUT | MUX_MODE0) /* lcd_vsync.lcd_vsync > */ > + 0xe4 (PIN_OUTPUT | MUX_MODE0) /* lcd_hsync.lcd_hsync > */ > + 0xe8 (PIN_OUTPUT | MUX_MODE0) /* lcd_pclk.lcd_pclk */ > + 0xec (PIN_OUTPUT | MUX_MODE0) /* > lcd_ac_bias_en.lcd_ac_bias_en */ > + /* Display Enable */ > + 0x6c (PIN_OUTPUT_PULLUP | MUX_MODE7) /* > gpmc_a11.gpio1_27 */ > + >; > + }; > +}; > + > +/* Ethernet */ > +&cpsw_emac0 { > + status = "okay"; > + phy_id = <&davinci_mdio>, <0>; > + phy-mode = "rgmii"; > +}; > + > +&cpsw_emac1 { > + status = "okay"; > + phy_id = <&davinci_mdio>, <1>; > + phy-mode = "rgmii"; > +}; > + > +&davinci_mdio { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&mdio_pins>; > +}; > + > +&mac { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <ðernet_pins>; > +}; > + > + > +&am33xx_pinmux { > + ethernet_pins: pinmux_ethernet { > + pinctrl-single,pins = < > + 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* > mii1_txen.rgmii1_tctl */ > + 0x118 (PIN_INPUT_PULLUP | MUX_MODE2) /* > mii1_rxdv.rgmii1_rctl */ > + 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* > mii1_txd3.rgmii1_td3 */ > + 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* > mii1_txd2.rgmii1_td2 */ > + 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* > mii1_txd1.rgmii1_td1 */ > + 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* > mii1_txd0.rgmii1_td0 */ > + 0x12c (PIN_INPUT_PULLUP | MUX_MODE2) /* > mii1_txclk.rgmii1_tclk */ > + 0x130 (PIN_INPUT_PULLUP | MUX_MODE2) /* > mii1_rxclk.rgmii1_rclk */ > + 0x134 (PIN_INPUT_PULLUP | MUX_MODE2) /* > mii1_rxd3.rgmii1_rxd3 */ > + 0x138 (PIN_INPUT_PULLUP | MUX_MODE2) /* > mii1_rxd2.rgmii1_rxd2 */ > + 0x13c (PIN_INPUT_PULLUP | MUX_MODE2) /* > mii1_rxd1.rgmii1_rxd1 */ > + 0x140 (PIN_INPUT_PULLUP | MUX_MODE2) /* > mii1_rxd0.rgmii1_rxd0 */ > + /* ethernet interrupt */ > + 0x144 (PIN_INPUT_PULLUP | MUX_MODE7) /* > rmii2_refclk.gpio0_29 */ > + /* ethernet PHY nReset */ > + 0x108 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* > mii1_col.gpio3_0 */ > + >; > + }; > + > + mdio_pins: pinmux_mdio { > + pinctrl-single,pins = < > + 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) > /* mdio_data.mdio_data */ > + 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) > /* mdio_clk.mdio_clk */ > + >; > + }; > +}; > + > +/* MMC */ > +&mmc1 { > + /* Bootable SD card slot */ > + status = "okay"; > + vmmc-supply = <&ldo3_reg>; > + bus-width = <4>; > + pinctrl-names = "default"; > + pinctrl-0 = <&sd_pins>; > + cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; > +}; > + > +&mmc2 { > + /* eMMC (not populated) on MMC #2 */ > + status = "disabled"; > + pinctrl-names = "default"; > + pinctrl-0 = <&emmc_pins>; > + vmmc-supply = <&ldo3_reg>; > + bus-width = <8>; > + ti,non-removable; > +}; > + > +&edma { > + /* Map eDMA MMC2 Events from Crossbar */ > + ti,edma-xbar-event-map = /bits/ 16 <1 12 > + 2 13>; > +}; > + > + > +&mmc3 { > + /* Wifi & Bluetooth on MMC #3 */ > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&wireless_pins>; > + vmmmc-supply = <&v3v3c_reg>; > + bus-width = <4>; > + ti,non-removable; > + dmas = <&edma 12 > + &edma 13>; > + dma-names = "tx", "rx"; > +}; > + > + > +&am33xx_pinmux { > + sd_pins: pinmux_sd_card { > + pinctrl-single,pins = < > + 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* > mmc0_dat0.mmc0_dat0 */ > + 0xf4 (PIN_INPUT_PULLUP | MUX_MODE0) /* > mmc0_dat1.mmc0_dat1 */ > + 0xf8 (PIN_INPUT_PULLUP | MUX_MODE0) /* > mmc0_dat2.mmc0_dat2 */ > + 0xfc (PIN_INPUT_PULLUP | MUX_MODE0) /* > mmc0_dat3.mmc0_dat3 */ > + 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* > mmc0_clk.mmc0_clk */ > + 0x104 (PIN_INPUT_PULLUP | MUX_MODE0) /* > mmc0_cmd.mmc0_cmd */ > + 0x160 (PIN_INPUT | MUX_MODE7) /* > spi0_cs1.gpio0_6 */ > + >; > + }; > + emmc_pins: pinmux_emmc { > + pinctrl-single,pins = < > + 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* > gpmc_csn1.mmc1_clk */ > + 0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* > gpmc_csn2.mmc1_cmd */ > + 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* > gpmc_ad0.mmc1_dat0 */ > + 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* > gpmc_ad1.mmc1_dat1 */ > + 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* > gpmc_ad2.mmc1_dat2 */ > + 0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* > gpmc_ad3.mmc1_dat3 */ > + 0x10 (PIN_INPUT_PULLUP | MUX_MODE1) /* > gpmc_ad4.mmc1_dat4 */ > + 0x14 (PIN_INPUT_PULLUP | MUX_MODE1) /* > gpmc_ad5.mmc1_dat5 */ > + 0x18 (PIN_INPUT_PULLUP | MUX_MODE1) /* > gpmc_ad6.mmc1_dat6 */ > + 0x1c (PIN_INPUT_PULLUP | MUX_MODE1) /* > gpmc_ad7.mmc1_dat7 */ > + /* EMMC nReset */ > + 0x74 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* > gpmc_wpn.gpio0_31 */ > + >; > + }; > + wireless_pins: pinmux_wireless { > + pinctrl-single,pins = < > + 0x44 (PIN_INPUT_PULLUP | MUX_MODE3) /* > gpmc_a1.mmc2_dat0 */ > + 0x48 (PIN_INPUT_PULLUP | MUX_MODE3) /* > gpmc_a2.mmc2_dat1 */ > + 0x4c (PIN_INPUT_PULLUP | MUX_MODE3) /* > gpmc_a3.mmc2_dat2 */ > + 0x78 (PIN_INPUT_PULLUP | MUX_MODE3) /* > gpmc_ben1.mmc2_dat3 */ > + 0x88 (PIN_INPUT_PULLUP | MUX_MODE3) /* > gpmc_csn3.mmc2_cmd */ > + 0x8c (PIN_INPUT_PULLUP | MUX_MODE3) /* > gpmc_clk.mmc1_clk */ > + /* WLAN nReset */ > + 0x60 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* > gpmc_a8.gpio1_24 */ > + /* WLAN nPower down */ > + 0x70 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* > gpmc_wait0.gpio0_30 */ > + /* 32kHz Clock */ > + 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* > xdma_event_intr1.clkout2 */ > + >; > + }; > +}; > + > +/* Power */ > +&vbat { > + regulator-name = "vbat"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > +}; > + > +&v3v3c_reg { > + regulator-name = "v3v3c_reg"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + vin-supply = <&vbat>; > + regulator-always-on; > +}; > + > +&vdd5_reg { > + regulator-name = "vdd5_reg"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + vin-supply = <&vbat>; > +}; > + > +/include/ "tps65217.dtsi" > + > +&tps { > + backlight { > + isel = <1>; /* ISET1 */ > + fdim = <200>; /* TPS65217_BL_FDIM_200HZ */ > + default-brightness = <80>; > + }; > + > + regulators { > + dcdc1_reg: regulator@0 { > + /* VDD_1V8 system supply */ > + regulator-always-on; > + }; > + > + dcdc2_reg: regulator@1 { > + /* VDD_CORE voltage limits 0.95V - 1.26V with +/-4% > tolerance */ > + regulator-name = "vdd_core"; > + regulator-min-microvolt = <925000>; > + regulator-max-microvolt = <1325000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + dcdc3_reg: regulator@2 { > + /* VDD_MPU voltage limits 0.95V - 1.1V with +/-4% > tolerance */ > + regulator-name = "vdd_mpu"; > + regulator-min-microvolt = <925000>; > + regulator-max-microvolt = <1150000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + ldo1_reg: regulator@3 { > + /* VRTC 1.8V always-on supply */ > + regulator-always-on; > + }; > + > + ldo2_reg: regulator@4 { > + /* 3.3V rail */ > + regulator-always-on; > + }; > + > + ldo3_reg: regulator@5 { > + /* VDD_3V3A 3.3V rail */ > + regulator-always-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + ldo4_reg: regulator@6 { > + /* VDD_3V3B 3.3V rail */ > + regulator-always-on; > + }; Why are all the regulators always on? Most of them should be managed automatically if you have correct dependencies, shouldn't they? > + }; > +}; > + > +/* SPI Busses */ > +&spi0 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&spi0_pins>; > +}; > + > +&am33xx_pinmux { > + spi0_pins: pinmux_spi0 { > + pinctrl-single,pins = < > + 0x150 (PIN_INPUT_PULLUP | MUX_MODE0) /* > spi0_sclk.spi0_sclk */ > + 0x15C (PIN_INPUT_PULLUP | MUX_MODE0) /* > spi0_cs0.spi0_cs0 */ > + 0x154 (PIN_INPUT_PULLUP | MUX_MODE0) /* spi0_d0.spi0_d0 > */ > + 0x158 (PIN_INPUT_PULLUP | MUX_MODE0) /* spi0_d1.spi0_d1 > */ > + >; > + }; > +}; > + > +/* Touch Screen */ > +&tscadc { > + status = "okay"; > + tsc { > + ti,wires = <4>; > + ti,x-plate-resistance = <200>; > + ti,coordinate-readouts = <5>; > + ti,wire-config = <0x00 0x11 0x22 0x33>; > + }; > + > + adc { > + ti,adc-channels = <4 5 6 7>; > + }; > +}; > + > +/* UARTs */ > +&uart0 { > + /* Serial Console */ > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&uart0_pins>; > +}; > + > +&uart1 { > + /* Broken out to J6 header */ > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&uart1_pins>; > +}; > + > +&am33xx_pinmux { > + uart0_pins: pinmux_uart0 { > + pinctrl-single,pins = < > + 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* > uart0_rxd.uart0_rxd */ > + 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* > uart0_txd.uart0_txd */ > + >; > + }; > + uart1_pins: pinmux_uart1 { > + pinctrl-single,pins = < > + 0x178 (PIN_INPUT_PULLUP | MUX_MODE0) /* > uart1_ctsn.uart1_ctsn */ > + 0x17C (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* > uart1_rtsn.uart1_rtsn */ > + 0x180 (PIN_INPUT_PULLUP | MUX_MODE0) /* > uart1_rxd.uart1_rxd */ > + 0x184 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* > uart1_txd.uart1_txd */ > + >; > + }; > +}; > + > +/* USB */ > +&usb { > + status = "okay"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&usb_pins>; > +}; > + > +&usb_ctrl_mod { > + status = "okay"; > +}; > + > +&usb0_phy { > + status = "okay"; > +}; > + > +&usb1_phy { > + status = "okay"; > +}; > + > +&usb0 { > + status = "okay"; > + dr_mode = "host"; > +}; > + > +&usb1 { > + status = "okay"; > + dr_mode = "host"; > +}; > + > +&cppi41dma { > + status = "okay"; > +}; > + > +&am33xx_pinmux { > + usb_pins: pinmux_usb { > + pinctrl-single,pins = < > + /* USB0 Over-Current (active low) */ > + 0x64 (PIN_INPUT | MUX_MODE7) /* gpmc_a9.gpio1_25 */ > + /* USB1 Over-Current (active low) */ > + 0x68 (PIN_INPUT | MUX_MODE7) /* gpmc_a10.gpio1_26 */ > + >; > + }; > +}; > + > +/* User IO */ > +&leds { > + pinctrl-names = "default"; > + pinctrl-0 = <&user_leds_pins>; > + > + led@0 { > + label = "pepper:user0:blue"; > + gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "none"; > + default-state = "off"; > + }; > + > + led@1 { > + label = "pepper:user1:red"; > + gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "none"; > + default-state = "off"; > + }; > +}; > + > +&buttons { > + pinctrl-names = "default"; > + pinctrl-0 = <&user_buttons_pins>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + button@0 { > + label = "home"; > + linux,code = <102>; You can use the key codes defined in <dt-bindings/input/input.h>. > + gpios = <&gpio1 22 GPIO_ACTIVE_LOW>; > + gpio-key,wakeup; > + }; > + > + button@1 { > + label = "menu"; > + linux,code = <139>; KEY_MENU > + gpios = <&gpio1 23 GPIO_ACTIVE_LOW>; > + gpio-key,wakeup; > + }; > + > + buttons@2 { > + label = "power"; > + linux,code = <116>; KEY_POWER > + gpios = <&gpio0 7 GPIO_ACTIVE_LOW>; > + gpio-key,wakeup; > + }; > +}; > + > +&am33xx_pinmux { > + user_leds_pins: pinmux_user_leds { > + pinctrl-single,pins = < > + 0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* > gpmc_a4.gpio1_20 */ > + 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* > gpmc_a5.gpio1_21 */ Why enabling the pulldown on an output gpio? You will increase the power consumption when driving high. > + >; > + }; > + > + user_buttons_pins: pinmux_user_buttons { > + pinctrl-single,pins = < > + 0x58 (PIN_INPUT_PULLUP | MUX_MODE7) /* > gpmc_a6.gpio1_22 */ > + 0x5C (PIN_INPUT_PULLUP | MUX_MODE7) /* > gpmc_a7.gpio1_21 */ > + 0x164 (PIN_INPUT_PULLUP | MUX_MODE7) /* > gpmc_a8.gpio0_7 */ > + >; > + }; > +}; > Regards, Florian -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
