On Tue, Aug 05, 2014 at 09:25:53AM -0400, Eduardo Valentin wrote:
> Hello Anson,
>
> On Tue, Aug 05, 2014 at 05:12:43PM +0800, Anson Huang wrote:
> > i.MX6SX has some new features of thermal interrupt function,
> > there are LOW, HIGH and PANIC irq for thermal sensor, so add
> > platform data to separate different thermal version;
> >
> > The reset value of LOW ALARM is 0 which means the highest
> > temp, so the LOW ALARM will be triggered once irq is enabled,
> > so we need to correct it before enabling thermal irq;
> >
> > Enable PANIC ALARM as critical trip point, it will trigger
> > system reset via SRC module once PANIC IRQ is triggered, it
> > is pure hardware function, so use it instead of software
> > reset by cooling device.
> >
> > Signed-off-by: Anson Huang <b20...@freescale.com>
> > ---
> > .../devicetree/bindings/thermal/imx-thermal.txt | 2 +-
> > drivers/thermal/imx_thermal.c | 88
> > +++++++++++++++++---
> > 2 files changed, 76 insertions(+), 14 deletions(-)
> >
> > diff --git a/Documentation/devicetree/bindings/thermal/imx-thermal.txt
> > b/Documentation/devicetree/bindings/thermal/imx-thermal.txt
> > index 1f0f672..95c05b1 100644
> > --- a/Documentation/devicetree/bindings/thermal/imx-thermal.txt
> > +++ b/Documentation/devicetree/bindings/thermal/imx-thermal.txt
> > @@ -1,7 +1,7 @@
> > * Temperature Monitor (TEMPMON) on Freescale i.MX SoCs
> >
> > Required properties:
> > -- compatible : "fsl,imx6q-thermal"
> > +- compatible : "fsl,imx6q-tempmon" for V1, "fsl,imx6sx-tempmon" for V2.
>
> It would be kind to document the difference between V1 and V2, don't you
> think?
Accepted, will add some brief summary about the new feature added on V2.
>
> > - fsl,tempmon : phandle pointer to system controller that contains TEMPMON
> > control registers, e.g. ANATOP on imx6q.
> > - fsl,tempmon-data : phandle pointer to fuse controller that contains
> > TEMPMON
> > diff --git a/drivers/thermal/imx_thermal.c b/drivers/thermal/imx_thermal.c
> > index 2c516f2..2276e74 100644
> > --- a/drivers/thermal/imx_thermal.c
> > +++ b/drivers/thermal/imx_thermal.c
> > @@ -19,6 +19,7 @@
> > #include <linux/mfd/syscon.h>
> > #include <linux/module.h>
> > #include <linux/of.h>
> > +#include <linux/of_device.h>
> > #include <linux/platform_device.h>
> > #include <linux/regmap.h>
> > #include <linux/slab.h>
> > @@ -31,6 +32,10 @@
> >
> > #define MISC0 0x0150
> > #define MISC0_REFTOP_SELBIASOFF (1 << 3)
> > +#define MISC1 0x0160
> > +#define MISC1_IRQ_TEMPHIGH (1 << 29)
> > +#define MISC1_IRQ_TEMPLOW (1 << 28)
> > +#define MISC1_IRQ_TEMPPANIC (1 << 27)
>
> how about using
> +#define MISC1_IRQ_TEMPHIGH BIT(29)
> +#define MISC1_IRQ_TEMPLOW BIT(28)
> +#define MISC1_IRQ_TEMPPANIC BIT(27)
>
Accepted, will improve it in V2 patch.
> >
> > #define TEMPSENSE0 0x0180
> > #define TEMPSENSE0_ALARM_VALUE_SHIFT 20
> > @@ -43,6 +48,11 @@
> >
> > #define TEMPSENSE1 0x0190
> > #define TEMPSENSE1_MEASURE_FREQ 0xffff
> > +#define TEMPSENSE2 0x0290
> > +#define TEMPSENSE2_LOW_VALUE_SHIFT 0
> > +#define TEMPSENSE2_LOW_VALUE_MASK 0xfff
> > +#define TEMPSENSE2_PANIC_VALUE_SHIFT 16
> > +#define TEMPSENSE2_PANIC_VALUE_MASK 0xfff0000
>
> Are the above register offsets and (bit) masks applicable to both
> versions? do you mind adding a comment to what is specific to V2?
>
Accepted, will add comments in V2 patch.
> >
> > #define OCOTP_ANA1 0x04e0
> >
> > @@ -66,6 +76,21 @@ enum imx_thermal_trip {
> > #define FACTOR1 15976
> > #define FACTOR2 4297157
> >
> > +#define TEMPMON_V1 1
> > +#define TEMPMON_V2 2
> > +
>
> where does the V1/V2 nomenclature come from? how about:
>
> +#define TEMPMON_IMX6Q 1
> +#define TEMPMON_IMX6SX 2
>
OK.
>
> > +struct thermal_soc_data {
> > + u32 version;
> > +};
> > +
> > +static struct thermal_soc_data thermal_imx6q_data = {
> > + .version = TEMPMON_V1,
> > +};
> > +
> > +static struct thermal_soc_data thermal_imx6sx_data = {
> > + .version = TEMPMON_V2,
> > +};
> > +
> > struct imx_thermal_data {
> > struct thermal_zone_device *tz;
> > struct thermal_cooling_device *cdev;
> > @@ -79,8 +104,21 @@ struct imx_thermal_data {
> > bool irq_enabled;
> > int irq;
> > struct clk *thermal_clk;
> > + const struct thermal_soc_data *socdata;
> > };
> >
> > +static void imx_set_panic_temp(struct imx_thermal_data *data,
> > + signed long panic_temp)
> > +{
> > + struct regmap *map = data->tempmon;
> > + int critical_value;
> > +
> > + critical_value = (data->c2 - panic_temp) / data->c1;
> > + regmap_write(map, TEMPSENSE2 + REG_CLR, TEMPSENSE2_PANIC_VALUE_MASK);
> > + regmap_write(map, TEMPSENSE2 + REG_SET, critical_value <<
> > + TEMPSENSE2_PANIC_VALUE_SHIFT);
> > +}
> > +
> > static void imx_set_alarm_temp(struct imx_thermal_data *data,
> > signed long alarm_temp)
> > {
> > @@ -142,13 +180,15 @@ static int imx_get_temp(struct thermal_zone_device
> > *tz, unsigned long *temp)
> > /* See imx_get_sensor_data() for formula derivation */
> > *temp = data->c2 - n_meas * data->c1;
> >
> > - /* Update alarm value to next higher trip point */
> > - if (data->alarm_temp == data->temp_passive && *temp >=
> > data->temp_passive)
> > - imx_set_alarm_temp(data, data->temp_critical);
> > - if (data->alarm_temp == data->temp_critical && *temp <
> > data->temp_passive) {
> > - imx_set_alarm_temp(data, data->temp_passive);
> > - dev_dbg(&tz->device, "thermal alarm off: T < %lu\n",
> > - data->alarm_temp / 1000);
> > + /* Update alarm value to next higher trip point, only V1 needs it */
> > + if (data->socdata->version == TEMPMON_V1) {
> > + if (data->alarm_temp == data->temp_passive && *temp >=
> > data->temp_passive)
> > + imx_set_alarm_temp(data, data->temp_critical);
> > + if (data->alarm_temp == data->temp_critical && *temp <
> > data->temp_passive) {
> > + imx_set_alarm_temp(data, data->temp_passive);
> > + dev_dbg(&tz->device, "thermal alarm off: T < %lu\n",
> > + data->alarm_temp / 1000);
> > + }
> > }
> >
> > if (*temp != data->last_temp) {
> > @@ -398,8 +438,17 @@ static irqreturn_t imx_thermal_alarm_irq_thread(int
> > irq, void *dev)
> > return IRQ_HANDLED;
> > }
> >
> > +static const struct of_device_id of_imx_thermal_match[] = {
> > + { .compatible = "fsl,imx6q-tempmon", .data = &thermal_imx6q_data, },
> > + { .compatible = "fsl,imx6sx-tempmon", .data = &thermal_imx6sx_data, },
> > + { /* end */ }
> > +};
> > +MODULE_DEVICE_TABLE(of, of_imx_thermal_match);
> > +
> > static int imx_thermal_probe(struct platform_device *pdev)
> > {
> > + const struct of_device_id *of_id =
> > + of_match_device(of_imx_thermal_match, &pdev->dev);
> > struct imx_thermal_data *data;
> > struct cpumask clip_cpus;
> > struct regmap *map;
> > @@ -418,6 +467,21 @@ static int imx_thermal_probe(struct platform_device
> > *pdev)
> > }
> > data->tempmon = map;
> >
> > + data->socdata = of_id->data;
> > +
> > + /* make sure the IRQ flag is clear before enable irq */
> > + regmap_write(map, MISC1 + REG_CLR, MISC1_IRQ_TEMPHIGH);
>
> Shouldn't this be also done only for TEMPMON_V2? What is the benefit /
> effect in doing for V1 ?
>
As on i.MX6SX, these bits are set by default, so we must clear them here, since
the TEMPHIGH is common for all i.MX6 SoCs, so I do it for both V1 and V2. But I
am
OK to move it to only for V2, as we did NOT meet any issue on V1 before. Will
move
it in patch V2.
Thanks for review!
Anson
> > + if (data->socdata->version == TEMPMON_V2) {
> > + regmap_write(map, MISC1 + REG_CLR, MISC1_IRQ_TEMPLOW |
> > + MISC1_IRQ_TEMPPANIC);
> > + /*
> > + * reset value of LOW ALARM is incorrect, set it to lowest
> > + * value to avoid false trigger of low alarm.
> > + */
> > + regmap_write(map, TEMPSENSE2 + REG_SET,
> > + TEMPSENSE2_LOW_VALUE_MASK);
> > + }
> > +
> > data->irq = platform_get_irq(pdev, 0);
> > if (data->irq < 0)
> > return data->irq;
> > @@ -489,6 +553,10 @@ static int imx_thermal_probe(struct platform_device
> > *pdev)
> > measure_freq = DIV_ROUND_UP(32768, 10); /* 10 Hz */
> > regmap_write(map, TEMPSENSE1 + REG_SET, measure_freq);
> > imx_set_alarm_temp(data, data->temp_passive);
> > +
> > + if (data->socdata->version == TEMPMON_V2)
> > + imx_set_panic_temp(data, data->temp_critical);
> > +
> > regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_POWER_DOWN);
> > regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_MEASURE_TEMP);
> >
> > @@ -550,12 +618,6 @@ static int imx_thermal_resume(struct device *dev)
> > static SIMPLE_DEV_PM_OPS(imx_thermal_pm_ops,
> > imx_thermal_suspend, imx_thermal_resume);
> >
> > -static const struct of_device_id of_imx_thermal_match[] = {
> > - { .compatible = "fsl,imx6q-tempmon", },
> > - { /* end */ }
> > -};
> > -MODULE_DEVICE_TABLE(of, of_imx_thermal_match);
> > -
> > static struct platform_driver imx_thermal = {
> > .driver = {
> > .name = "imx_thermal",
> > --
> > 1.7.9.5
> >
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
