Use the gpio contants defined in bindings for active high/low
Signed-off-by: Tim Harvey <[email protected]>
---
arch/arm/boot/dts/imx6q-gw5400-a.dts | 23 ++++++++++++-----------
arch/arm/boot/dts/imx6qdl-gw51xx.dtsi | 14 ++++++++------
arch/arm/boot/dts/imx6qdl-gw52xx.dtsi | 22 ++++++++++++----------
arch/arm/boot/dts/imx6qdl-gw53xx.dtsi | 22 ++++++++++++----------
arch/arm/boot/dts/imx6qdl-gw54xx.dtsi | 22 ++++++++++++----------
5 files changed, 56 insertions(+), 47 deletions(-)
diff --git a/arch/arm/boot/dts/imx6q-gw5400-a.dts
b/arch/arm/boot/dts/imx6q-gw5400-a.dts
index 035f2b1..9687cd8 100644
--- a/arch/arm/boot/dts/imx6q-gw5400-a.dts
+++ b/arch/arm/boot/dts/imx6q-gw5400-a.dts
@@ -10,6 +10,7 @@
*/
/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
#include "imx6q.dtsi"
/ {
@@ -40,20 +41,20 @@
led0: user1 {
label = "user1";
- gpios = <&gpio4 6 0>; /* 102 -> MX6_PANLEDG */
+ gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* 102 ->
MX6_PANLEDG */
default-state = "on";
linux,default-trigger = "heartbeat";
};
led1: user2 {
label = "user2";
- gpios = <&gpio4 10 0>; /* 106 -> MX6_PANLEDR */
+ gpios = <&gpio4 10 GPIO_ACTIVE_HIGH>; /* 106 ->
MX6_PANLEDR */
default-state = "off";
};
led2: user3 {
label = "user3";
- gpios = <&gpio4 15 1>; /* 111 -> MX6_LOCLED# */
+ gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* 111 ->
MX6_LOCLED# */
default-state = "off";
};
};
@@ -64,7 +65,7 @@
pps {
compatible = "pps-gpio";
- gpios = <&gpio1 5 0>;
+ gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
status = "okay";
};
@@ -106,7 +107,7 @@
regulator-name = "usb_otg_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- gpio = <&gpio3 22 0>;
+ gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
};
@@ -134,7 +135,7 @@
&ecspi1 {
fsl,spi-num-chipselects = <1>;
- cs-gpios = <&gpio3 19 0>;
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi1>;
status = "okay";
@@ -150,7 +151,7 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii";
- phy-reset-gpios = <&gpio1 30 0>;
+ phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
status = "okay";
};
@@ -331,8 +332,8 @@
compatible = "eeti,egalax_ts";
reg = <0x04>;
interrupt-parent = <&gpio7>;
- interrupts = <12 2>; /* gpio7_12 active low */
- wakeup-gpios = <&gpio7 12 0>;
+ interrupts = <12 2>;
+ wakeup-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
};
};
@@ -462,7 +463,7 @@
};
&pcie {
- reset-gpio = <&gpio1 29 0>;
+ reset-gpio = <&gpio1 29 GPIO_ACTIVE_LOW>;
status = "okay";
eth1: sky2@8 { /* MAC/PHY on bus 8 */
@@ -508,7 +509,7 @@
&usdhc3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc3>;
- cd-gpios = <&gpio7 0 0>;
+ cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
vmmc-supply = <®_3p3v>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
b/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
index 482ef28..fa2cae4 100644
--- a/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
@@ -9,6 +9,8 @@
* http://www.gnu.org/copyleft/gpl.html
*/
+#include <dt-bindings/gpio/gpio.h>
+
/ {
/* these are used by bootloader for disabling nodes */
aliases {
@@ -28,14 +30,14 @@
led0: user1 {
label = "user1";
- gpios = <&gpio4 6 0>; /* 102 -> MX6_PANLEDG */
+ gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
default-state = "on";
linux,default-trigger = "heartbeat";
};
led1: user2 {
label = "user2";
- gpios = <&gpio4 7 0>; /* 103 -> MX6_PANLEDR */
+ gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
default-state = "off";
};
};
@@ -46,7 +48,7 @@
pps {
compatible = "pps-gpio";
- gpios = <&gpio1 26 0>;
+ gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
status = "okay";
};
@@ -79,7 +81,7 @@
regulator-name = "usb_otg_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- gpio = <&gpio3 22 0>;
+ gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
};
@@ -89,7 +91,7 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii";
- phy-reset-gpios = <&gpio1 30 0>;
+ phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
status = "okay";
};
@@ -279,7 +281,7 @@
};
&pcie {
- reset-gpio = <&gpio1 0 0>;
+ reset-gpio = <&gpio1 0 GPIO_ACTIVE_LOW>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
index f8c4ab4..53f4a0b 100644
--- a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
@@ -9,6 +9,8 @@
* http://www.gnu.org/copyleft/gpl.html
*/
+#include <dt-bindings/gpio/gpio.h>
+
/ {
/* these are used by bootloader for disabling nodes */
aliases {
@@ -37,20 +39,20 @@
led0: user1 {
label = "user1";
- gpios = <&gpio4 6 0>; /* 102 -> MX6_PANLEDG */
+ gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
default-state = "on";
linux,default-trigger = "heartbeat";
};
led1: user2 {
label = "user2";
- gpios = <&gpio4 7 0>; /* 103 -> MX6_PANLEDR */
+ gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
default-state = "off";
};
led2: user3 {
label = "user3";
- gpios = <&gpio4 15 1>; /* 111 - MX6_LOCLED# */
+ gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* MX6_LOCLED# */
default-state = "off";
};
};
@@ -61,7 +63,7 @@
pps {
compatible = "pps-gpio";
- gpios = <&gpio1 26 0>;
+ gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
status = "okay";
};
@@ -113,7 +115,7 @@
regulator-name = "usb_otg_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- gpio = <&gpio3 22 0>;
+ gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
};
@@ -143,7 +145,7 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii";
- phy-reset-gpios = <&gpio1 30 0>;
+ phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
status = "okay";
};
@@ -226,8 +228,8 @@
compatible = "eeti,egalax_ts";
reg = <0x04>;
interrupt-parent = <&gpio7>;
- interrupts = <12 2>; /* gpio7_12 active low */
- wakeup-gpios = <&gpio7 12 0>;
+ interrupts = <12 2>;
+ wakeup-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
};
};
@@ -402,7 +404,7 @@
};
&pcie {
- reset-gpio = <&gpio1 29 0>;
+ reset-gpio = <&gpio1 29 GPIO_ACTIVE_LOW>;
status = "okay";
};
@@ -449,7 +451,7 @@
&usdhc3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc3>;
- cd-gpios = <&gpio7 0 0>;
+ cd-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
vmmc-supply = <®_3p3v>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
index 01edfd99..2074df6 100644
--- a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
@@ -9,6 +9,8 @@
* http://www.gnu.org/copyleft/gpl.html
*/
+#include <dt-bindings/gpio/gpio.h>
+
/ {
/* these are used by bootloader for disabling nodes */
aliases {
@@ -38,20 +40,20 @@
led0: user1 {
label = "user1";
- gpios = <&gpio4 6 0>; /* 102 -> MX6_PANLEDG */
+ gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
default-state = "on";
linux,default-trigger = "heartbeat";
};
led1: user2 {
label = "user2";
- gpios = <&gpio4 7 0>; /* 103 -> MX6_PANLEDR */
+ gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
default-state = "off";
};
led2: user3 {
label = "user3";
- gpios = <&gpio4 15 1>; /* 111 -> MX6_LOCLED# */
+ gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* MX6_LOCLED# */
default-state = "off";
};
};
@@ -62,7 +64,7 @@
pps {
compatible = "pps-gpio";
- gpios = <&gpio1 26 0>;
+ gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
status = "okay";
};
@@ -114,7 +116,7 @@
regulator-name = "usb_otg_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- gpio = <&gpio3 22 0>;
+ gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
};
@@ -150,7 +152,7 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii";
- phy-reset-gpios = <&gpio1 30 0>;
+ phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
status = "okay";
};
@@ -233,8 +235,8 @@
compatible = "eeti,egalax_ts";
reg = <0x04>;
interrupt-parent = <&gpio1>;
- interrupts = <11 2>; /* gpio1_11 active low */
- wakeup-gpios = <&gpio1 11 0>;
+ interrupts = <11 2>;
+ wakeup-gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
};
};
@@ -418,7 +420,7 @@
};
&pcie {
- reset-gpio = <&gpio1 29 0>;
+ reset-gpio = <&gpio1 29 GPIO_ACTIVE_LOW>;
status = "okay";
eth1: sky2@8 { /* MAC/PHY on bus 8 */
@@ -470,7 +472,7 @@
&usdhc3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc3>;
- cd-gpios = <&gpio7 0 0>;
+ cd-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
vmmc-supply = <®_3p3v>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
index fab9c7a..ab7827a 100644
--- a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
@@ -9,6 +9,8 @@
* http://www.gnu.org/copyleft/gpl.html
*/
+#include <dt-bindings/gpio/gpio.h>
+
/ {
/* these are used by bootloader for disabling nodes */
aliases {
@@ -38,20 +40,20 @@
led0: user1 {
label = "user1";
- gpios = <&gpio4 6 0>; /* 102 -> MX6_PANLEDG */
+ gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
default-state = "on";
linux,default-trigger = "heartbeat";
};
led1: user2 {
label = "user2";
- gpios = <&gpio4 7 0>; /* 103 -> MX6_PANLEDR */
+ gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
default-state = "off";
};
led2: user3 {
label = "user3";
- gpios = <&gpio4 15 1>; /* 111 -> MX6_LOCLED# */
+ gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* MX6_LOCLED# */
default-state = "off";
};
};
@@ -62,7 +64,7 @@
pps {
compatible = "pps-gpio";
- gpios = <&gpio1 26 0>;
+ gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
status = "okay";
};
@@ -104,7 +106,7 @@
regulator-name = "usb_otg_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- gpio = <&gpio3 22 0>;
+ gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
};
@@ -140,7 +142,7 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii";
- phy-reset-gpios = <&gpio1 30 0>;
+ phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
status = "okay";
};
@@ -322,8 +324,8 @@
compatible = "eeti,egalax_ts";
reg = <0x04>;
interrupt-parent = <&gpio7>;
- interrupts = <12 2>; /* gpio7_12 active low */
- wakeup-gpios = <&gpio7 12 0>;
+ interrupts = <12 2>;
+ wakeup-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
};
};
@@ -501,7 +503,7 @@
};
&pcie {
- reset-gpio = <&gpio1 29 0>;
+ reset-gpio = <&gpio1 29 GPIO_ACTIVE_LOW>;
status = "okay";
eth1: sky2@8 { /* MAC/PHY on bus 8 */
@@ -557,7 +559,7 @@
&usdhc3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc3>;
- cd-gpios = <&gpio7 0 0>;
+ cd-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
vmmc-supply = <®_3p3v>;
status = "okay";
};
--
1.8.3.2
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
