[adding devicetree folks...]
On Fri, Oct 03, 2014 at 02:03:57PM -0700, Dmitry Torokhov wrote:
> Hi Duson,
>
> On Tue, Jan 07, 2014 at 11:08:03AM +0800, Duson Lin wrote:
> > This driver adds support for elan i2c/smbus touchpad found on some
> > laptops PC
> >
>
> I was looking at your original patch together with varous other patchs
> for the device in ChromeOS trees and I ended up with the following
> version. Please take a look and shout if you see something wrong.
>
> The SMbus portion is untested as I do not have hardware; I2C does work
> on actual hardware.
>
> Thanks.
>
> --
> Dmitry
>
> Input: driver for Elan I2C/SMbus touchpad
>
> From: Duson Lin <duson...@emc.com.tw>
>
> This driver supports Elan I2C/SMbous touchpads found in some laptops and
> also in many Chromebooks.
>
> Signed-off-by: Duson Lin <duson...@emc.com.tw>
> Signed-off-by: Dmitry Torokhov <dmitry.torok...@gmail.com>
> ---
> .../devicetree/bindings/input/elan_i2c.txt | 34 +
> .../devicetree/bindings/vendor-prefixes.txt | 1
> drivers/input/mouse/Kconfig | 30 +
> drivers/input/mouse/Makefile | 5
> drivers/input/mouse/elan_i2c.h | 86 ++
> drivers/input/mouse/elan_i2c_core.c | 1129
> ++++++++++++++++++++
> drivers/input/mouse/elan_i2c_i2c.c | 612 +++++++++++
> drivers/input/mouse/elan_i2c_smbus.c | 514 +++++++++
> 8 files changed, 2411 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/input/elan_i2c.txt
> create mode 100644 drivers/input/mouse/elan_i2c.h
> create mode 100644 drivers/input/mouse/elan_i2c_core.c
> create mode 100644 drivers/input/mouse/elan_i2c_i2c.c
> create mode 100644 drivers/input/mouse/elan_i2c_smbus.c
>
> diff --git a/Documentation/devicetree/bindings/input/elan_i2c.txt
> b/Documentation/devicetree/bindings/input/elan_i2c.txt
> new file mode 100644
> index 0000000..0a6ee7d
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/input/elan_i2c.txt
> @@ -0,0 +1,34 @@
> +Elantech I2C Touchpad
> +
> +Required properties:
> +- compatible: must be "elan,i2c_touchpad".
> +- reg: I2C address of the chip.
> +- interrupt-parent: a phandle for the gpio controller (see interrupt
> + binding[0]).
> +- interrupts: (gpio) interrupt to which the chip is connected (see interrupt
> + binding[0]).
> +
> +Optional properties:
> +- wakeup-source: touchpad should be configured as a wakeup source.
> +- pinctrl-names: should be "default" (see pinctrl binding [1]).
> +- pinctrl-0: a phandle pointing to the pin settings for the device (see
> + pinctrl binding [1]).
> +- vcc-supply: a phandle for the regulator supplying 3.3V power.
> +
> +[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
> +[1]: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
> +
> +Example:
> + &i2c1 {
> + /* ... */
> +
> + touchpad@15 {
> + compatible = "elan,i2c_touchpad";
> + reg = <0x15>;
> + interrupt-parent = <&gpio4>;
> + interrupts = <0x0 IRQ_TYPE_EDGE_FALLING>;
> + wakeup-source;
> + };
> +
> + /* ... */
> + };
> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt
> b/Documentation/devicetree/bindings/vendor-prefixes.txt
> index ac7269f..e6469ec 100644
> --- a/Documentation/devicetree/bindings/vendor-prefixes.txt
> +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
> @@ -42,6 +42,7 @@ dlink D-Link Corporation
> dmo Data Modul AG
> ebv EBV Elektronik
> edt Emerging Display Technologies
> +elan Elan Microelectronic Corp.
> emmicro EM Microelectronic
> epcos EPCOS AG
> epfl Ecole Polytechnique Fédérale de Lausanne
> diff --git a/drivers/input/mouse/Kconfig b/drivers/input/mouse/Kconfig
> index 366fc7a..d8b46b0 100644
> --- a/drivers/input/mouse/Kconfig
> +++ b/drivers/input/mouse/Kconfig
> @@ -215,6 +215,36 @@ config MOUSE_CYAPA
> To compile this driver as a module, choose M here: the module will be
> called cyapa.
>
> +config MOUSE_ELAN_I2C
> + tristate "ELAN I2C Touchpad support"
> + depends on I2C
> + help
> + This driver adds support for Elan I2C/SMbus Trackpads.
> +
> + Say Y here if you have a ELAN I2C/SMbus Touchpad.
> +
> + To compile this driver as a module, choose M here: the module will be
> + called elan_i2c.
> +
> +config MOUSE_ELAN_I2C_I2C
> + bool "Enable I2C support"
> + depends on MOUSE_ELAN_I2C
> + default y
> + help
> + Say Y here if Elan Touchpad in your system is connected to
> + a standard I2C controller.
> +
> + If unsure, say Y.
> +
> +config MOUSE_ELAN_I2C_SMBUS
> + bool "Enable SMbus support"
> + depends on MOUSE_ELAN_I2C
> + help
> + Say Y here if Elan Touchpad in your system is connected to
> + a SMbus adapter.
> +
> + If unsure, say Y.
> +
> config MOUSE_INPORT
> tristate "InPort/MS/ATIXL busmouse"
> depends on ISA
> diff --git a/drivers/input/mouse/Makefile b/drivers/input/mouse/Makefile
> index dda507f..560003d 100644
> --- a/drivers/input/mouse/Makefile
> +++ b/drivers/input/mouse/Makefile
> @@ -9,6 +9,7 @@ obj-$(CONFIG_MOUSE_APPLETOUCH) += appletouch.o
> obj-$(CONFIG_MOUSE_ATARI) += atarimouse.o
> obj-$(CONFIG_MOUSE_BCM5974) += bcm5974.o
> obj-$(CONFIG_MOUSE_CYAPA) += cyapa.o
> +obj-$(CONFIG_MOUSE_ELAN_I2C) += elan_i2c.o
> obj-$(CONFIG_MOUSE_GPIO) += gpio_mouse.o
> obj-$(CONFIG_MOUSE_INPORT) += inport.o
> obj-$(CONFIG_MOUSE_LOGIBM) += logibm.o
> @@ -34,3 +35,7 @@ psmouse-$(CONFIG_MOUSE_PS2_SENTELIC) += sentelic.o
> psmouse-$(CONFIG_MOUSE_PS2_TRACKPOINT) += trackpoint.o
> psmouse-$(CONFIG_MOUSE_PS2_TOUCHKIT) += touchkit_ps2.o
> psmouse-$(CONFIG_MOUSE_PS2_CYPRESS) += cypress_ps2.o
> +
> +elan_i2c-objs := elan_i2c_core.o
> +elan_i2c-$(CONFIG_MOUSE_ELAN_I2C_I2C) += elan_i2c_i2c.o
> +elan_i2c-$(CONFIG_MOUSE_ELAN_I2C_SMBUS) += elan_i2c_smbus.o
> diff --git a/drivers/input/mouse/elan_i2c.h b/drivers/input/mouse/elan_i2c.h
> new file mode 100644
> index 0000000..2e83862
> --- /dev/null
> +++ b/drivers/input/mouse/elan_i2c.h
> @@ -0,0 +1,86 @@
> +/*
> + * Elan I2C/SMBus Touchpad driver
> + *
> + * Copyright (c) 2013 ELAN Microelectronics Corp.
> + *
> + * Author: 林政維 (Duson Lin) <duson...@emc.com.tw>
> + * Version: 1.5.5
> + *
> + * Based on cyapa driver:
> + * copyright (c) 2011-2012 Cypress Semiconductor, Inc.
> + * copyright (c) 2011-2012 Google, Inc.
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License version 2 as published
> + * by the Free Software Foundation.
> + *
> + * Trademarks are the property of their respective owners.
> + */
> +
> +#ifndef _ELAN_I2C_H
> +#define _ELAN_i2C_H
> +
> +#include <linux/types.h>
> +
> +#define ETP_ENABLE_ABS 0x0001
> +#define ETP_ENABLE_CALIBRATE 0x0002
> +#define ETP_DISABLE_CALIBRATE 0x0000
> +#define ETP_DISABLE_POWER 0x0001
> +
> +/* IAP Firmware handling */
> +#define ETP_FW_NAME "elan_i2c.bin"
> +#define ETP_IAP_START_ADDR 0x0083
> +#define ETP_FW_IAP_PAGE_ERR (1 << 5)
> +#define ETP_FW_IAP_INTF_ERR (1 << 4)
> +#define ETP_FW_PAGE_SIZE 64
> +#define ETP_FW_PAGE_COUNT 768
> +#define ETP_FW_SIZE (ETP_FW_PAGE_SIZE * ETP_FW_PAGE_COUNT)
> +
> +struct i2c_client;
> +struct completion;
> +
> +enum tp_mode {
> + IAP_MODE = 1,
> + MAIN_MODE
> +};
> +
> +struct elan_transport_ops {
> + int (*initialize)(struct i2c_client *client);
> + int (*sleep_control)(struct i2c_client *, bool sleep);
> + int (*power_control)(struct i2c_client *, bool enable);
> + int (*set_mode)(struct i2c_client *client, u8 mode);
> +
> + int (*calibrate)(struct i2c_client *client);
> + int (*calibrate_result)(struct i2c_client *client, u8 *val);
> +
> + int (*get_baseline_data)(struct i2c_client *client,
> + bool max_baseliune, u8 *value);
> +
> + int (*get_version)(struct i2c_client *client, bool iap, u8 *version);
> + int (*get_sm_version)(struct i2c_client *client, u8 *version);
> + int (*get_checksum)(struct i2c_client *client, bool iap, u16 *csum);
> + int (*get_product_id)(struct i2c_client *client, u8 *id);
> +
> + int (*get_max)(struct i2c_client *client,
> + unsigned int *max_x, unsigned int *max_y);
> + int (*get_resolution)(struct i2c_client *client,
> + u8 *hw_res_x, u8 *hw_res_y);
> + int (*get_num_traces)(struct i2c_client *client,
> + unsigned int *x_tracenum,
> + unsigned int *y_tracenum);
> +
> + int (*iap_get_mode)(struct i2c_client *client, enum tp_mode *mode);
> + int (*iap_reset)(struct i2c_client *client);
> +
> + int (*prepare_fw_update)(struct i2c_client *client);
> + int (*write_fw_block)(struct i2c_client *client,
> + const u8 *page, u16 checksum, int idx);
> + int (*finish_fw_update)(struct i2c_client *client,
> + struct completion *reset_done);
> +
> + int (*get_report)(struct i2c_client *client, u8 *report);
> +};
> +
> +extern const struct elan_transport_ops elan_smbus_ops, elan_i2c_ops;
> +
> +#endif /* _ELAN_I2C_H */
> diff --git a/drivers/input/mouse/elan_i2c_core.c
> b/drivers/input/mouse/elan_i2c_core.c
> new file mode 100644
> index 0000000..f1e5e30
> --- /dev/null
> +++ b/drivers/input/mouse/elan_i2c_core.c
> @@ -0,0 +1,1129 @@
> +/*
> + * Elan I2C/SMBus Touchpad driver
> + *
> + * Copyright (c) 2013 ELAN Microelectronics Corp.
> + *
> + * Author: 林政維 (Duson Lin) <duson...@emc.com.tw>
> + * Version: 1.5.5
> + *
> + * Based on cyapa driver:
> + * copyright (c) 2011-2012 Cypress Semiconductor, Inc.
> + * copyright (c) 2011-2012 Google, Inc.
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License version 2 as published
> + * by the Free Software Foundation.
> + *
> + * Trademarks are the property of their respective owners.
> + */
> +
> +#include <linux/acpi.h>
> +#include <linux/delay.h>
> +#include <linux/device.h>
> +#include <linux/firmware.h>
> +#include <linux/i2c.h>
> +#include <linux/init.h>
> +#include <linux/input/mt.h>
> +#include <linux/interrupt.h>
> +#include <linux/module.h>
> +#include <linux/slab.h>
> +#include <linux/kernel.h>
> +#include <linux/sched.h>
> +#include <linux/input.h>
> +#include <linux/uaccess.h>
> +#include <linux/jiffies.h>
> +#include <linux/completion.h>
> +#include <linux/of.h>
> +#include <linux/regulator/consumer.h>
> +#include <asm/unaligned.h>
> +
> +#include "elan_i2c.h"
> +
> +#define DRIVER_NAME "elan_i2c"
> +#define ELAN_DRIVER_VERSION "1.5.5"
> +#define ETP_PRESSURE_OFFSET 25
> +#define ETP_MAX_PRESSURE 255
> +#define ETP_FWIDTH_REDUCE 90
> +#define ETP_FINGER_WIDTH 15
> +#define ETP_RETRY_COUNT 3
> +
> +#define ETP_MAX_FINGERS 5
> +#define ETP_FINGER_DATA_LEN 5
> +#define ETP_REPORT_ID 0x5D
> +#define ETP_REPORT_ID_OFFSET 2
> +#define ETP_TOUCH_INFO_OFFSET 3
> +#define ETP_FINGER_DATA_OFFSET 4
> +#define ETP_MAX_REPORT_LEN 34
> +
> +/* The main device structure */
> +struct elan_tp_data {
> + struct i2c_client *client;
> + struct input_dev *input;
> + struct regulator *vcc;
> +
> + const struct elan_transport_ops *ops;
> +
> + /* for fw update */
> + struct completion fw_completion;
> + bool in_fw_update;
> +
> + struct mutex sysfs_mutex;
> +
> + unsigned int max_x;
> + unsigned int max_y;
> + unsigned int width_x;
> + unsigned int width_y;
> + unsigned int x_res;
> + unsigned int y_res;
> +
> + u8 product_id;
> + u8 fw_version;
> + u8 sm_version;
> + u8 iap_version;
> + u16 fw_checksum;
> +
> + u8 mode;
> +
> + bool irq_wake;
> +
> + u8 min_baseline;
> + u8 max_baseline;
> + bool baseline_ready;
> +};
> +
> +static int elan_enable_power(struct elan_tp_data *data)
> +{
> + int repeat = ETP_RETRY_COUNT;
> + int error;
> +
> + error = regulator_enable(data->vcc);
> + if (error) {
> + dev_err(&data->client->dev,
> + "Failed to enable regulator: %d\n", error);
> + return error;
> + }
> +
> + do {
> + error = data->ops->power_control(data->client, true);
> + if (error >= 0)
> + return 0;
> +
> + msleep(30);
> + } while (--repeat > 0);
> +
> + return error;
> +}
> +
> +static int elan_disable_power(struct elan_tp_data *data)
> +{
> + int repeat = ETP_RETRY_COUNT;
> + int error;
> +
> + do {
> + error = data->ops->power_control(data->client, false);
> + if (!error) {
> + error = regulator_disable(data->vcc);
> + if (error) {
> + dev_err(&data->client->dev,
> + "Failed to disable regulator: %d\n",
> + error);
> + /* Attempt to power the chip back up */
> + data->ops->power_control(data->client, true);
> + break;
> + }
> +
> + return 0;
> + }
> +
> + msleep(30);
> + } while (--repeat > 0);
> +
> + return error;
> +}
> +
> +static int elan_sleep(struct elan_tp_data *data)
> +{
> + int repeat = ETP_RETRY_COUNT;
> + int error;
> +
> + do {
> + error = data->ops->sleep_control(data->client, true);
> + if (!error)
> + return 0;
> +
> + msleep(30);
> + } while (--repeat > 0);
> +
> + return error;
> +}
> +
> +static int __elan_initialize(struct elan_tp_data *data)
> +{
> + struct i2c_client *client = data->client;
> + int error;
> +
> + error = data->ops->initialize(client);
> + if (error) {
> + dev_err(&client->dev, "device initialize failed: %d\n", error);
> + return error;
> + }
> +
> + data->mode |= ETP_ENABLE_ABS;
> + error = data->ops->set_mode(client, data->mode);
> + if (error) {
> + dev_err(&client->dev,
> + "failed to switch to absolute mode: %d\n", error);
> + return error;
> + }
> +
> + error = data->ops->sleep_control(client, false);
> + if (error) {
> + dev_err(&client->dev,
> + "failed to wake device up: %d\n", error);
> + return error;
> + }
> +
> + return 0;
> +}
> +
> +static int elan_initialize(struct elan_tp_data *data)
> +{
> + int repeat = ETP_RETRY_COUNT;
> + int error;
> +
> + do {
> + error = __elan_initialize(data);
> + if (!error)
> + return 0;
> +
> + repeat--;
> + msleep(30);
> + } while (--repeat > 0);
> +
> + return error;
> +}
> +
> +static int elan_query_device_info(struct elan_tp_data *data)
> +{
> + int error;
> +
> + error = data->ops->get_product_id(data->client, &data->product_id);
> + if (error)
> + return error;
> +
> + error = data->ops->get_version(data->client, false, &data->fw_version);
> + if (error)
> + return error;
> +
> + error = data->ops->get_checksum(data->client, false,
> + &data->fw_checksum);
> + if (error)
> + return error;
> +
> + error = data->ops->get_sm_version(data->client, &data->sm_version);
> + if (error)
> + return error;
> +
> + error = data->ops->get_version(data->client, true, &data->iap_version);
> + if (error)
> + return error;
> +
> + return 0;
> +}
> +
> +static unsigned int elan_convert_resolution(u8 val)
> +{
> + /*
> + * (value from firmware) * 10 + 790 = dpi
> + *
> + * We also have to convert dpi to dots/mm (*10/254 to avoid floating
> + * point).
> + */
> +
> + return ((int)(char)val * 10 + 790) * 10 / 254;
> +}
> +
> +static int elan_query_device_parameters(struct elan_tp_data *data)
> +{
> + unsigned int x_traces, y_traces;
> + u8 hw_x_res, hw_y_res;
> + int error;
> +
> + error = data->ops->get_max(data->client, &data->max_x, &data->max_y);
> + if (error)
> + return error;
> +
> + error = data->ops->get_num_traces(data->client, &x_traces, &y_traces);
> + if (error)
> + return error;
> +
> + data->width_x = data->max_x / x_traces;
> + data->width_y = data->max_y / y_traces;
> +
> + error = data->ops->get_resolution(data->client, &hw_x_res, &hw_y_res);
> + if (error)
> + return error;
> +
> + data->x_res = elan_convert_resolution(hw_x_res);
> + data->y_res = elan_convert_resolution(hw_y_res);
> +
> + return 0;
> +}
> +
> +/*
> + **********************************************************
> + * IAP firmware updater related routines
> + **********************************************************
> + */
> +static int elan_write_fw_block(struct elan_tp_data *data,
> + const u8 *page, u16 checksum, int idx)
> +{
> + int retry = ETP_RETRY_COUNT;
> + int error;
> +
> + do {
> + error = data->ops->write_fw_block(data->client,
> + page, checksum, idx);
> + if (!error)
> + return 0;
> +
> + dev_dbg(&data->client->dev,
> + "IAP retrying page %d (error: %d)\n", idx, error);
> + } while (--retry > 0);
> +
> + return error;
> +}
> +
> +static int __elan_update_firmware(struct elan_tp_data *data,
> + const struct firmware *fw)
> +{
> + struct i2c_client *client = data->client;
> + struct device *dev = &client->dev;
> + int i, j;
> + int error;
> + u16 iap_start_addr;
> + u16 boot_page_count;
> + u16 sw_checksum = 0, fw_checksum = 0;
> +
> + error = data->ops->prepare_fw_update(client);
> + if (error)
> + return error;
> +
> + iap_start_addr = get_unaligned_le16(&fw->data[ETP_IAP_START_ADDR * 2]);
> +
> + boot_page_count = (iap_start_addr * 2) / ETP_FW_PAGE_SIZE;
> + for (i = boot_page_count; i < ETP_FW_PAGE_COUNT; i++) {
> + u16 checksum = 0;
> + const u8 *page = &fw->data[i * ETP_FW_PAGE_SIZE];
> +
> + for (j = 0; j < ETP_FW_PAGE_SIZE; j += 2)
> + checksum += ((page[j + 1] << 8) | page[j]);
> +
> + error = elan_write_fw_block(data, page, checksum, i);
> + if (error) {
> + dev_err(dev, "write page %d fail: %d\n", i, error);
> + return error;
> + }
> +
> + sw_checksum += checksum;
> + }
> +
> + /* Wait WDT reset and power on reset */
> + msleep(600);
> +
> + error = data->ops->finish_fw_update(client, &data->fw_completion);
> + if (error)
> + return error;
> +
> + error = data->ops->get_checksum(client, true, &fw_checksum);
> + if (error)
> + return error;
> +
> + if (sw_checksum != fw_checksum) {
> + dev_err(dev, "checksum diff sw=[%04X], fw=[%04X]\n",
> + sw_checksum, fw_checksum);
> + return -EIO;
> + }
> +
> + return 0;
> +}
> +
> +static int elan_update_firmware(struct elan_tp_data *data,
> + const struct firmware *fw)
> +{
> + struct i2c_client *client = data->client;
> + int retval;
> +
> + dev_dbg(&client->dev, "Starting firmware update....\n");
> +
> + disable_irq(client->irq);
> + data->in_fw_update = true;
> +
> + retval = __elan_update_firmware(data, fw);
> + if (retval) {
> + dev_err(&client->dev, "firmware update failed: %d\n", retval);
> + data->ops->iap_reset(client);
> + } else {
> + /* Reinitialize TP after fw is updated */
> + elan_initialize(data);
> + elan_query_device_info(data);
> + }
> +
> + data->in_fw_update = false;
> + enable_irq(client->irq);
> +
> + return retval;
> +}
> +
> +
> +/*
> + *******************************************************************
> + * SYSFS attributes
> + *******************************************************************
> + */
> +static ssize_t elan_sysfs_read_fw_checksum(struct device *dev,
> + struct device_attribute *attr,
> + char *buf)
> +{
> + struct elan_tp_data *data = dev_get_drvdata(dev);
> +
> + return sprintf(buf, "0x%04x\n", data->fw_checksum);
> +}
> +
> +static ssize_t elan_sysfs_read_product_id(struct device *dev,
> + struct device_attribute *attr,
> + char *buf)
> +{
> + struct elan_tp_data *data = dev_get_drvdata(dev);
> +
> + return sprintf(buf, "%d.0\n", data->product_id);
> +}
> +
> +static ssize_t elan_sysfs_read_fw_ver(struct device *dev,
> + struct device_attribute *attr,
> + char *buf)
> +{
> + struct elan_tp_data *data = dev_get_drvdata(dev);
> +
> + return sprintf(buf, "%d.0\n", data->fw_version);
> +}
> +
> +static ssize_t elan_sysfs_read_sm_ver(struct device *dev,
> + struct device_attribute *attr,
> + char *buf)
> +{
> + struct elan_tp_data *data = dev_get_drvdata(dev);
> +
> + return sprintf(buf, "%d.0\n", data->sm_version);
> +}
> +
> +static ssize_t elan_sysfs_read_iap_ver(struct device *dev,
> + struct device_attribute *attr,
> + char *buf)
> +{
> + struct elan_tp_data *data = dev_get_drvdata(dev);
> +
> + return sprintf(buf, "%d.0\n", data->iap_version);
> +}
> +
> +static ssize_t elan_sysfs_update_fw(struct device *dev,
> + struct device_attribute *attr,
> + const char *buf, size_t count)
> +{
> + struct elan_tp_data *data = dev_get_drvdata(dev);
> + const struct firmware *fw;
> + int error;
> +
> + error = request_firmware(&fw, ETP_FW_NAME, dev);
> + if (error) {
> + dev_err(dev, "cannot load firmware %s: %d\n",
> + ETP_FW_NAME, error);
> + return error;
> + }
> +
> + /* Firmware must be exactly PAGE_NUM * PAGE_SIZE bytes */
> + if (fw->size != ETP_FW_SIZE) {
> + dev_err(dev, "invalid firmware size = %zu, expected %d.\n",
> + fw->size, ETP_FW_SIZE);
> + error = -EBADF;
> + goto out_release_fw;
> + }
> +
> + error = mutex_lock_interruptible(&data->sysfs_mutex);
> + if (error)
> + goto out_release_fw;
> +
> + error = elan_update_firmware(data, fw);
> +
> + mutex_unlock(&data->sysfs_mutex);
> +
> +out_release_fw:
> + release_firmware(fw);
> + return error ?: count;
> +}
> +
> +static ssize_t calibrate_store(struct device *dev,
> + struct device_attribute *attr,
> + const char *buf, size_t count)
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct elan_tp_data *data = i2c_get_clientdata(client);
> + int tries = 20;
> + int retval;
> + int error;
> + u8 val[3];
> +
> + retval = mutex_lock_interruptible(&data->sysfs_mutex);
> + if (retval)
> + return retval;
> +
> + disable_irq(client->irq);
> +
> + data->mode |= ETP_ENABLE_CALIBRATE;
> + retval = data->ops->set_mode(client, data->mode);
> + if (retval) {
> + dev_err(dev, "failed to enable calibration mode: %d\n",
> + retval);
> + goto out;
> + }
> +
> + retval = data->ops->calibrate(client);
> + if (retval) {
> + dev_err(dev, "failed to start calibration: %d\n",
> + retval);
> + goto out_disable_calibrate;
> + }
> +
> + val[0] = 0xff;
> + do {
> + /* Wait 250ms before checking if calibration has completed. */
> + msleep(250);
> +
> + retval = data->ops->calibrate_result(client, val);
> + if (retval)
> + dev_err(dev, "failed to check calibration result: %d\n",
> + retval);
> + else if (val[0] == 0)
> + break; /* calibration done */
> +
> + } while (--tries);
> +
> + if (tries == 0) {
> + dev_err(dev, "failed to calibrate. Timeout.\n");
> + retval = -ETIMEDOUT;
> + }
> +
> +out_disable_calibrate:
> + data->mode &= ~ETP_ENABLE_CALIBRATE;
> + error = data->ops->set_mode(data->client, data->mode);
> + if (error) {
> + dev_err(dev, "failed to disable calibration mode: %d\n",
> + error);
> + if (!retval)
> + retval = error;
> + }
> +out:
> + enable_irq(client->irq);
> + mutex_unlock(&data->sysfs_mutex);
> + return retval ?: count;
> +}
> +
> +static ssize_t elan_sysfs_read_mode(struct device *dev,
> + struct device_attribute *attr,
> + char *buf)
> +{
> + struct elan_tp_data *data = dev_get_drvdata(dev);
> + int error;
> + enum tp_mode mode;
> +
> + error = mutex_lock_interruptible(&data->sysfs_mutex);
> + if (error)
> + return error;
> +
> + error = data->ops->iap_get_mode(data->client, &mode);
> +
> + mutex_unlock(&data->sysfs_mutex);
> +
> + if (error)
> + return error;
> +
> + return sprintf(buf, "%d\n", (int)mode);
> +}
> +
> +static DEVICE_ATTR(product_id, S_IRUGO, elan_sysfs_read_product_id, NULL);
> +static DEVICE_ATTR(firmware_version, S_IRUGO, elan_sysfs_read_fw_ver, NULL);
> +static DEVICE_ATTR(sample_version, S_IRUGO, elan_sysfs_read_sm_ver, NULL);
> +static DEVICE_ATTR(iap_version, S_IRUGO, elan_sysfs_read_iap_ver, NULL);
> +static DEVICE_ATTR(fw_checksum, S_IRUGO, elan_sysfs_read_fw_checksum, NULL);
> +static DEVICE_ATTR(mode, S_IRUGO, elan_sysfs_read_mode, NULL);
> +static DEVICE_ATTR(update_fw, S_IWUSR, NULL, elan_sysfs_update_fw);
> +
> +static DEVICE_ATTR_WO(calibrate);
> +
> +static struct attribute *elan_sysfs_entries[] = {
> + &dev_attr_product_id.attr,
> + &dev_attr_firmware_version.attr,
> + &dev_attr_sample_version.attr,
> + &dev_attr_iap_version.attr,
> + &dev_attr_fw_checksum.attr,
> + &dev_attr_calibrate.attr,
> + &dev_attr_mode.attr,
> + &dev_attr_update_fw.attr,
> + NULL,
> +};
> +
> +static const struct attribute_group elan_sysfs_group = {
> + .attrs = elan_sysfs_entries,
> +};
> +
> +static ssize_t acquire_store(struct device *dev, struct device_attribute
> *attr,
> + const char *buf, size_t count)
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct elan_tp_data *data = i2c_get_clientdata(client);
> + int error;
> + int retval;
> +
> + retval = mutex_lock_interruptible(&data->sysfs_mutex);
> + if (retval)
> + return retval;
> +
> + disable_irq(client->irq);
> +
> + data->baseline_ready = false;
> +
> + data->mode |= ETP_ENABLE_CALIBRATE;
> + retval = data->ops->set_mode(data->client, data->mode);
> + if (retval) {
> + dev_err(dev, "Failed to enable calibration mode to get
> baseline: %d\n",
> + retval);
> + goto out;
> + }
> +
> + msleep(250);
> +
> + retval = data->ops->get_baseline_data(data->client, true,
> + &data->max_baseline);
> + if (retval) {
> + dev_err(dev, "Failed to read max baseline form device: %d\n",
> + retval);
> + goto out_disable_calibrate;
> + }
> +
> + retval = data->ops->get_baseline_data(data->client, false,
> + &data->min_baseline);
> + if (retval) {
> + dev_err(dev, "Failed to read min baseline form device: %d\n",
> + retval);
> + goto out_disable_calibrate;
> + }
> +
> + data->baseline_ready = true;
> +
> +out_disable_calibrate:
> + data->mode &= ~ETP_ENABLE_CALIBRATE;
> + error = data->ops->set_mode(data->client, data->mode);
> + if (error) {
> + dev_err(dev, "Failed to disable calibration mode after
> acquiring baseline: %d\n",
> + error);
> + if (!retval)
> + retval = error;
> + }
> +out:
> + enable_irq(client->irq);
> + mutex_unlock(&data->sysfs_mutex);
> + return retval ?: count;
> +}
> +
> +static ssize_t min_show(struct device *dev,
> + struct device_attribute *attr, char *buf)
> +{
> + struct elan_tp_data *data = dev_get_drvdata(dev);
> + int retval;
> +
> + retval = mutex_lock_interruptible(&data->sysfs_mutex);
> + if (retval)
> + return retval;
> +
> + if (!data->baseline_ready) {
> + retval = -ENODATA;
> + goto out;
> + }
> +
> + retval = snprintf(buf, PAGE_SIZE, "%d", data->min_baseline);
> +
> +out:
> + mutex_unlock(&data->sysfs_mutex);
> + return retval;
> +}
> +
> +static ssize_t max_show(struct device *dev,
> + struct device_attribute *attr, char *buf)
> +{
> + struct elan_tp_data *data = dev_get_drvdata(dev);
> + int retval;
> +
> + retval = mutex_lock_interruptible(&data->sysfs_mutex);
> + if (retval)
> + return retval;
> +
> + if (!data->baseline_ready) {
> + retval = -ENODATA;
> + goto out;
> + }
> +
> + retval = snprintf(buf, PAGE_SIZE, "%d", data->max_baseline);
> +
> +out:
> + mutex_unlock(&data->sysfs_mutex);
> + return retval;
> +}
> +
> +
> +static DEVICE_ATTR_WO(acquire);
> +static DEVICE_ATTR_RO(min);
> +static DEVICE_ATTR_RO(max);
> +
> +static struct attribute *elan_baseline_sysfs_entries[] = {
> + &dev_attr_acquire.attr,
> + &dev_attr_min.attr,
> + &dev_attr_max.attr,
> + NULL,
> +};
> +
> +static const struct attribute_group elan_baseline_sysfs_group = {
> + .name = "baseline",
> + .attrs = elan_baseline_sysfs_entries,
> +};
> +
> +static const struct attribute_group *elan_sysfs_groups[] = {
> + &elan_sysfs_group,
> + &elan_baseline_sysfs_group,
> + NULL
> +};
> +
> +/*
> + ******************************************************************
> + * Elan isr functions
> + ******************************************************************
> + */
> +static void elan_report_contact(struct elan_tp_data *data,
> + int contact_num, bool contact_valid,
> + u8 *finger_data)
> +{
> + struct input_dev *input = data->input;
> + unsigned int pos_x, pos_y;
> + unsigned int pressure, mk_x, mk_y;
> + unsigned int area_x, area_y, major, minor, new_pressure;
> +
> +
> + if (contact_valid) {
> + pos_x = ((finger_data[0] & 0xf0) << 4) |
> + finger_data[1];
> + pos_y = ((finger_data[0] & 0x0f) << 8) |
> + finger_data[2];
> + mk_x = (finger_data[3] & 0x0f);
> + mk_y = (finger_data[3] >> 4);
> + pressure = finger_data[4];
> +
> + if (pos_x > data->max_x || pos_y > data->max_y) {
> + dev_dbg(input->dev.parent,
> + "[%d] x=%d y=%d over max (%d, %d)",
> + contact_num, pos_x, pos_y,
> + data->max_x, data->max_y);
> + return;
> + }
> +
> + /*
> + * To avoid treating large finger as palm, let's reduce the
> + * width x and y per trace.
> + */
> + area_x = mk_x * (data->width_x - ETP_FWIDTH_REDUCE);
> + area_y = mk_y * (data->width_y - ETP_FWIDTH_REDUCE);
> +
> + major = max(area_x, area_y);
> + minor = min(area_x, area_y);
> +
> + new_pressure = pressure + ETP_PRESSURE_OFFSET;
> + if (new_pressure > ETP_MAX_PRESSURE)
> + new_pressure = ETP_MAX_PRESSURE;
> +
> + input_mt_slot(input, contact_num);
> + input_mt_report_slot_state(input, MT_TOOL_FINGER, true);
> + input_report_abs(input, ABS_MT_POSITION_X, pos_x);
> + input_report_abs(input, ABS_MT_POSITION_Y, data->max_y - pos_y);
> + input_report_abs(input, ABS_MT_PRESSURE, new_pressure);
> + input_report_abs(input, ABS_TOOL_WIDTH, mk_x);
> + input_report_abs(input, ABS_MT_TOUCH_MAJOR, major);
> + input_report_abs(input, ABS_MT_TOUCH_MINOR, minor);
> + } else {
> + input_mt_slot(input, contact_num);
> + input_mt_report_slot_state(input, MT_TOOL_FINGER, false);
> + }
> +}
> +
> +static void elan_report_absolute(struct elan_tp_data *data, u8 *packet)
> +{
> + struct input_dev *input = data->input;
> + u8 *finger_data = &packet[ETP_FINGER_DATA_OFFSET];
> + int i;
> + u8 tp_info = packet[ETP_TOUCH_INFO_OFFSET];
> + bool contact_valid;
> +
> + for (i = 0; i < ETP_MAX_FINGERS; i++) {
> + contact_valid = tp_info & (1U << (3 + i));
> + elan_report_contact(data, i, contact_valid, finger_data);
> +
> + if (contact_valid)
> + finger_data += ETP_FINGER_DATA_LEN;
> + }
> +
> + input_report_key(input, BTN_LEFT, tp_info & 0x01);
> + input_mt_report_pointer_emulation(input, true);
> + input_sync(input);
> +}
> +
> +static irqreturn_t elan_isr(int irq, void *dev_id)
> +{
> + struct elan_tp_data *data = dev_id;
> + struct device *dev = &data->client->dev;
> + int error;
> + u8 report[ETP_MAX_REPORT_LEN];
> +
> + /*
> + * When device is connected to i2c bus, when all IAP page writes
> + * complete, the driver will receive interrupt and must read
> + * 0000 to confirm that IAP is finished.
> + */
> + if (data->in_fw_update) {
> + complete(&data->fw_completion);
> + goto out;
> + }
> +
> + error = data->ops->get_report(data->client, report);
> + if (error)
> + goto out;
> +
> + if (report[ETP_REPORT_ID_OFFSET] != ETP_REPORT_ID)
> + dev_err(dev, "invalid report id data (%x)\n",
> + report[ETP_REPORT_ID_OFFSET]);
> + else
> + elan_report_absolute(data, report);
> +
> +out:
> + return IRQ_HANDLED;
> +}
> +
> +/*
> + ******************************************************************
> + * Elan initialization functions
> + ******************************************************************
> + */
> +static int elan_setup_input_device(struct elan_tp_data *data)
> +{
> + struct device *dev = &data->client->dev;
> + struct input_dev *input;
> + unsigned int max_width = max(data->width_x, data->width_y);
> + unsigned int min_width = min(data->width_x, data->width_y);
> + int error;
> +
> + input = devm_input_allocate_device(dev);
> + if (!input)
> + return -ENOMEM;
> +
> + input->name = "Elan Touchpad";
> + input->id.bustype = BUS_I2C;
> + input_set_drvdata(input, data);
> +
> + error = input_mt_init_slots(input, ETP_MAX_FINGERS,
> + INPUT_MT_POINTER | INPUT_MT_DROP_UNUSED);
> + if (error) {
> + dev_err(dev, "failed to initialize MT slots: %d\n", error);
> + return error;
> + }
> +
> + __set_bit(EV_ABS, input->evbit);
> + __set_bit(INPUT_PROP_POINTER, input->propbit);
> + __set_bit(INPUT_PROP_BUTTONPAD, input->propbit);
> + __set_bit(BTN_LEFT, input->keybit);
> +
> + /* Set up ST parameters */
> + input_set_abs_params(input, ABS_X, 0, data->max_x, 0, 0);
> + input_set_abs_params(input, ABS_Y, 0, data->max_y, 0, 0);
> + input_abs_set_res(input, ABS_X, data->x_res);
> + input_abs_set_res(input, ABS_Y, data->y_res);
> + input_set_abs_params(input, ABS_PRESSURE, 0, ETP_MAX_PRESSURE, 0, 0);
> + input_set_abs_params(input, ABS_TOOL_WIDTH, 0, ETP_FINGER_WIDTH, 0, 0);
> +
> + /* And MT parameters */
> + input_set_abs_params(input, ABS_MT_POSITION_X, 0, data->max_x, 0, 0);
> + input_set_abs_params(input, ABS_MT_POSITION_Y, 0, data->max_y, 0, 0);
> + input_abs_set_res(input, ABS_MT_POSITION_X, data->x_res);
> + input_abs_set_res(input, ABS_MT_POSITION_Y, data->y_res);
> + input_set_abs_params(input, ABS_MT_PRESSURE, 0,
> + ETP_MAX_PRESSURE, 0, 0);
> + input_set_abs_params(input, ABS_MT_TOUCH_MAJOR, 0,
> + ETP_FINGER_WIDTH * max_width, 0, 0);
> + input_set_abs_params(input, ABS_MT_TOUCH_MINOR, 0,
> + ETP_FINGER_WIDTH * min_width, 0, 0);
> +
> + data->input = input;
> +
> + return 0;
> +}
> +
> +static void elan_disable_regulator(void *_data)
> +{
> + struct elan_tp_data *data = _data;
> +
> + regulator_disable(data->vcc);
> +}
> +
> +static void elan_remove_sysfs_groups(void *_data)
> +{
> + struct elan_tp_data *data = _data;
> +
> + sysfs_remove_groups(&data->client->dev.kobj, elan_sysfs_groups);
> +}
> +
> +static int elan_probe(struct i2c_client *client,
> + const struct i2c_device_id *dev_id)
> +{
> + const struct elan_transport_ops *transport_ops;
> + struct device *dev = &client->dev;
> + struct elan_tp_data *data;
> + unsigned long irqflags;
> + int error;
> +
> + if (IS_ENABLED(CONFIG_MOUSE_ELAN_I2C_I2C) &&
> + i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
> + transport_ops = &elan_i2c_ops;
> + } else if (IS_ENABLED(CONFIG_MOUSE_ELAN_I2C_SMBUS) &&
> + i2c_check_functionality(client->adapter,
> + I2C_FUNC_SMBUS_BYTE_DATA |
> + I2C_FUNC_SMBUS_BLOCK_DATA |
> + I2C_FUNC_SMBUS_I2C_BLOCK)) {
> + transport_ops = &elan_smbus_ops;
> + } else {
> + dev_err(dev, "not a supported I2C/SMBus adapter\n");
> + return -EIO;
> + }
> +
> + data = devm_kzalloc(&client->dev, sizeof(struct elan_tp_data),
> + GFP_KERNEL);
> + if (!data)
> + return -ENOMEM;
> +
> + data->ops = transport_ops;
> + data->client = client;
> + init_completion(&data->fw_completion);
> + mutex_init(&data->sysfs_mutex);
> +
> + data->vcc = devm_regulator_get(&client->dev, "vcc");
> + if (IS_ERR(data->vcc)) {
> + error = PTR_ERR(data->vcc);
> + if (error != -EPROBE_DEFER)
> + dev_err(&client->dev,
> + "Failed to get 'vcc' regulator: %d\n",
> + error);
> + return error;
> + }
> +
> + error = regulator_enable(data->vcc);
> + if (error) {
> + dev_err(&client->dev,
> + "Failed to enable regulator: %d\n", error);
> + return error;
> + }
> +
> + error = devm_add_action(&client->dev,
> + elan_disable_regulator, data);
> + if (error) {
> + regulator_disable(data->vcc);
> + dev_err(&client->dev,
> + "Failed to add disable regulator action: %d\n",
> + error);
> + return error;
> + }
> +
> + /* Initialize the touchpad. */
> + error = elan_initialize(data);
> + if (error)
> + return error;
> +
> + error = elan_query_device_info(data);
> + if (error)
> + return error;
> +
> + error = elan_query_device_parameters(data);
> + if (error)
> + return error;
> +
> + dev_dbg(&client->dev,
> + "Elan Touchpad Information:\n"
> + " Module product ID: 0x%04x\n"
> + " Firmware Version: 0x%04x\n"
> + " Sample Version: 0x%04x\n"
> + " IAP Version: 0x%04x\n"
> + " Max ABS X,Y: %d,%d\n"
> + " Width X,Y: %d,%d\n"
> + " Resolution X,Y: %d,%d (dots/mm)\n",
> + data->product_id,
> + data->fw_version,
> + data->sm_version,
> + data->iap_version,
> + data->max_x, data->max_y,
> + data->width_x, data->width_y,
> + data->x_res, data->y_res);
> +
> + /* Set up input device properties based on queried parameters. */
> + error = elan_setup_input_device(data);
> + if (error)
> + return error;
> +
> + /*
> + * Systems using device tree should set up interrupt via DTS,
> + * the rest will use the default falling edge interrupts.
> + */
> + irqflags = client->dev.of_node ? 0 : IRQF_TRIGGER_FALLING;
> +
> + error = devm_request_threaded_irq(&client->dev, client->irq,
> + NULL, elan_isr,
> + irqflags | IRQF_ONESHOT,
> + client->name, data);
> + if (error) {
> + dev_err(&client->dev, "cannot register irq=%d\n", client->irq);
> + return error;
> + }
> +
> + error = sysfs_create_groups(&client->dev.kobj, elan_sysfs_groups);
> + if (error) {
> + dev_err(&client->dev, "failed to create sysfs attributes: %d\n",
> + error);
> + return error;
> + }
> +
> + error = devm_add_action(&client->dev,
> + elan_remove_sysfs_groups, data);
> + if (error) {
> + elan_remove_sysfs_groups(data);
> + dev_err(&client->dev,
> + "Failed to add sysfs cleanup action: %d\n",
> + error);
> + return error;
> + }
> +
> + error = input_register_device(data->input);
> + if (error) {
> + dev_err(&client->dev, "failed to register input device: %d\n",
> + error);
> + return error;
> + }
> +
> + /*
> + * Systems using device tree should set up wakeup via DTS,
> + * the rest will configure device as wakeup source by default.
> + */
> + if (!client->dev.of_node)
> + device_init_wakeup(&client->dev, true);
> +
> + i2c_set_clientdata(client, data);
> +
> + return 0;
> +}
> +
> +static int __maybe_unused elan_suspend(struct device *dev)
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct elan_tp_data *data = i2c_get_clientdata(client);
> + int ret;
> +
> + /*
> + * We are taking the mutex to make sure sysfs operations are
> + * complete before we attempt to bring the device into low[er]
> + * power mode.
> + */
> + ret = mutex_lock_interruptible(&data->sysfs_mutex);
> + if (ret)
> + return ret;
> +
> + disable_irq(client->irq);
> +
> + if (device_may_wakeup(dev)) {
> + ret = elan_sleep(data);
> + /* Enable wake from IRQ */
> + data->irq_wake = (enable_irq_wake(client->irq) == 0);
> + } else {
> + ret = elan_disable_power(data);
> + }
> +
> + mutex_unlock(&data->sysfs_mutex);
> + return ret;
> +}
> +
> +static int __maybe_unused elan_resume(struct device *dev)
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct elan_tp_data *data = i2c_get_clientdata(client);
> + int error;
> +
> + if (device_may_wakeup(dev) && data->irq_wake) {
> + disable_irq_wake(client->irq);
> + data->irq_wake = false;
> + }
> +
> + error = elan_enable_power(data);
> + if (error)
> + dev_err(dev, "power up when resuming failed: %d\n", error);
> +
> + error = elan_initialize(data);
> + if (error)
> + dev_err(dev, "initialize when resuming failed: %d\n", error);
> +
> + enable_irq(data->client->irq);
> +
> + return 0;
> +}
> +
> +static SIMPLE_DEV_PM_OPS(elan_pm_ops, elan_suspend, elan_resume);
> +
> +static const struct i2c_device_id elan_id[] = {
> + { DRIVER_NAME, 0 },
> + { },
> +};
> +MODULE_DEVICE_TABLE(i2c, elan_id);
> +
> +#ifdef CONFIG_ACPI
> +static const struct acpi_device_id elan_acpi_id[] = {
> + { "ELAN0000", 0 },
> + { }
> +};
> +MODULE_DEVICE_TABLE(acpi, elan_acpi_id);
> +#endif
> +
> +#ifdef CONFIG_OF
> +static const struct of_device_id elan_of_match[] = {
> + { .compatible = "elan,i2c_touchpad" },
> + { /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, elan_of_match);
> +#endif
> +
> +static struct i2c_driver elan_driver = {
> + .driver = {
> + .name = DRIVER_NAME,
> + .owner = THIS_MODULE,
> + .pm = &elan_pm_ops,
> + .acpi_match_table = ACPI_PTR(elan_acpi_id),
> + .of_match_table = of_match_ptr(elan_of_match),
> + },
> + .probe = elan_probe,
> + .id_table = elan_id,
> +};
> +
> +module_i2c_driver(elan_driver);
> +
> +MODULE_AUTHOR("Duson Lin <duson...@emc.com.tw>");
> +MODULE_DESCRIPTION("Elan I2C/SMBus Touchpad driver");
> +MODULE_LICENSE("GPL");
> +MODULE_VERSION(ELAN_DRIVER_VERSION);
> diff --git a/drivers/input/mouse/elan_i2c_i2c.c
> b/drivers/input/mouse/elan_i2c_i2c.c
> new file mode 100644
> index 0000000..047b257
> --- /dev/null
> +++ b/drivers/input/mouse/elan_i2c_i2c.c
> @@ -0,0 +1,612 @@
> +/*
> + * Elan I2C/SMBus Touchpad driver - I2C interface
> + *
> + * Copyright (c) 2013 ELAN Microelectronics Corp.
> + *
> + * Author: 林政維 (Duson Lin) <duson...@emc.com.tw>
> + * Version: 1.5.5
> + *
> + * Based on cyapa driver:
> + * copyright (c) 2011-2012 Cypress Semiconductor, Inc.
> + * copyright (c) 2011-2012 Google, Inc.
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License version 2 as published
> + * by the Free Software Foundation.
> + *
> + * Trademarks are the property of their respective owners.
> + */
> +
> +#include <linux/completion.h>
> +#include <linux/delay.h>
> +#include <linux/i2c.h>
> +#include <linux/interrupt.h>
> +#include <linux/jiffies.h>
> +#include <linux/kernel.h>
> +#include <linux/sched.h>
> +#include <asm/unaligned.h>
> +
> +#include "elan_i2c.h"
> +
> +/* Elan i2c commands */
> +#define ETP_I2C_RESET 0x0100
> +#define ETP_I2C_WAKE_UP 0x0800
> +#define ETP_I2C_SLEEP 0x0801
> +#define ETP_I2C_DESC_CMD 0x0001
> +#define ETP_I2C_REPORT_DESC_CMD 0x0002
> +#define ETP_I2C_STAND_CMD 0x0005
> +#define ETP_I2C_UNIQUEID_CMD 0x0101
> +#define ETP_I2C_FW_VERSION_CMD 0x0102
> +#define ETP_I2C_SM_VERSION_CMD 0x0103
> +#define ETP_I2C_XY_TRACENUM_CMD 0x0105
> +#define ETP_I2C_MAX_X_AXIS_CMD 0x0106
> +#define ETP_I2C_MAX_Y_AXIS_CMD 0x0107
> +#define ETP_I2C_RESOLUTION_CMD 0x0108
> +#define ETP_I2C_IAP_VERSION_CMD 0x0110
> +#define ETP_I2C_SET_CMD 0x0300
> +#define ETP_I2C_POWER_CMD 0x0307
> +#define ETP_I2C_FW_CHECKSUM_CMD 0x030F
> +#define ETP_I2C_IAP_CTRL_CMD 0x0310
> +#define ETP_I2C_IAP_CMD 0x0311
> +#define ETP_I2C_IAP_RESET_CMD 0x0314
> +#define ETP_I2C_IAP_CHECKSUM_CMD 0x0315
> +#define ETP_I2C_CALIBRATE_CMD 0x0316
> +#define ETP_I2C_MAX_BASELINE_CMD 0x0317
> +#define ETP_I2C_MIN_BASELINE_CMD 0x0318
> +
> +#define ETP_I2C_REPORT_LEN 34
> +#define ETP_I2C_DESC_LENGTH 30
> +#define ETP_I2C_REPORT_DESC_LENGTH 158
> +#define ETP_I2C_INF_LENGTH 2
> +#define ETP_I2C_IAP_PASSWORD 0x1EA5
> +#define ETP_I2C_IAP_RESET 0xF0F0
> +#define ETP_I2C_MAIN_MODE_ON (1 << 9)
> +#define ETP_I2C_IAP_REG_L 0x01
> +#define ETP_I2C_IAP_REG_H 0x06
> +
> +static int elan_i2c_read_block(struct i2c_client *client,
> + u16 reg, u8 *val, u16 len)
> +{
> + __le16 buf[] = {
> + cpu_to_le16(reg),
> + };
> + struct i2c_msg msgs[] = {
> + {
> + .addr = client->addr,
> + .flags = client->flags & I2C_M_TEN,
> + .len = sizeof(buf),
> + .buf = (u8 *)buf,
> + },
> + {
> + .addr = client->addr,
> + .flags = (client->flags & I2C_M_TEN) | I2C_M_RD,
> + .len = len,
> + .buf = val,
> + }
> + };
> + int ret;
> +
> + ret = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs));
> + return ret == ARRAY_SIZE(msgs) ? 0 : (ret < 0 ? ret : -EIO);
> +}
> +
> +static int elan_i2c_read_cmd(struct i2c_client *client, u16 reg, u8 *val)
> +{
> + int retval;
> +
> + retval = elan_i2c_read_block(client, reg, val, ETP_I2C_INF_LENGTH);
> + if (retval < 0) {
> + dev_err(&client->dev, "reading cmd (0x%04x) fail.\n", reg);
> + return retval;
> + }
> +
> + return 0;
> +}
> +
> +static int elan_i2c_write_cmd(struct i2c_client *client, u16 reg, u16 cmd)
> +{
> + __le16 buf[] = {
> + cpu_to_le16(reg),
> + cpu_to_le16(cmd),
> + };
> + struct i2c_msg msg = {
> + .addr = client->addr,
> + .flags = client->flags & I2C_M_TEN,
> + .len = sizeof(buf),
> + .buf = (u8 *)buf,
> + };
> + int ret;
> +
> + ret = i2c_transfer(client->adapter, &msg, 1);
> + return ret == 1 ? 0 : (ret < 0 ? ret : -EIO);
> +}
> +
> +static int elan_i2c_initialize(struct i2c_client *client)
> +{
> + struct device *dev = &client->dev;
> + int error;
> + u8 val[256];
> +
> + error = elan_i2c_write_cmd(client, ETP_I2C_STAND_CMD, ETP_I2C_RESET);
> + if (error) {
> + dev_err(dev, "device reset failed: %d\n", error);
> + return error;
> + }
> +
> + /* Wait for the device to reset */
> + msleep(100);
> +
> + /* get reset acknowledgement 0000 */
> + error = i2c_master_recv(client, val, ETP_I2C_INF_LENGTH);
> + if (error < 0) {
> + dev_err(dev, "failed to read reset response: %d\n", error);
> + return error;
> + }
> +
> + error = elan_i2c_read_block(client, ETP_I2C_DESC_CMD,
> + val, ETP_I2C_DESC_LENGTH);
> + if (error) {
> + dev_err(dev, "cannot get device descriptor: %d\n", error);
> + return error;
> + }
> +
> + error = elan_i2c_read_block(client, ETP_I2C_REPORT_DESC_CMD,
> + val, ETP_I2C_REPORT_DESC_LENGTH);
> + if (error) {
> + dev_err(dev, "fetching report descriptor failed.: %d\n", error);
> + return error;
> + }
> +
> + return 0;
> +}
> +
> +static int elan_i2c_sleep_control(struct i2c_client *client, bool sleep)
> +{
> + return elan_i2c_write_cmd(client, ETP_I2C_STAND_CMD,
> + sleep ? ETP_I2C_SLEEP : ETP_I2C_WAKE_UP);
> +}
> +
> +static int elan_i2c_power_control(struct i2c_client *client, bool enable)
> +{
> + u8 val[2];
> + u16 reg;
> + int error;
> +
> + error = elan_i2c_read_cmd(client, ETP_I2C_POWER_CMD, val);
> + if (error) {
> + dev_err(&client->dev,
> + "failed to read current power state: %d\n",
> + error);
> + return error;
> + }
> +
> + reg = le16_to_cpup((__le16 *)val);
> + if (enable)
> + reg &= ~ETP_DISABLE_POWER;
> + else
> + reg |= ETP_DISABLE_POWER;
> +
> + error = elan_i2c_write_cmd(client, ETP_I2C_POWER_CMD,
> + cpu_to_le16(reg));
> + if (error) {
> + dev_err(&client->dev,
> + "failed to write current power state: %d\n",
> + error);
> + return error;
> + }
> +
> + return 0;
> +}
> +
> +static int elan_i2c_set_mode(struct i2c_client *client, u8 mode)
> +{
> + return elan_i2c_write_cmd(client, ETP_I2C_SET_CMD, mode);
> +}
> +
> +
> +static int elan_i2c_calibrate(struct i2c_client *client)
> +{
> + return elan_i2c_write_cmd(client, ETP_I2C_CALIBRATE_CMD, 1);
> +}
> +
> +static int elan_i2c_calibrate_result(struct i2c_client *client, u8 *val)
> +{
> + return elan_i2c_read_block(client, ETP_I2C_CALIBRATE_CMD, val, 1);
> +}
> +
> +static int elan_i2c_get_baseline_data(struct i2c_client *client,
> + bool max_baseline, u8 *value)
> +{
> + int error;
> + u8 val[3];
> +
> + error = elan_i2c_read_cmd(client,
> + max_baseline ? ETP_I2C_MAX_BASELINE_CMD :
> + ETP_I2C_MIN_BASELINE_CMD,
> + val);
> + if (error)
> + return error;
> +
> + *value = le16_to_cpup((__le16 *)val);
> +
> + return 0;
> +}
> +
> +static int elan_i2c_get_version(struct i2c_client *client,
> + bool iap, u8 *version)
> +{
> + int error;
> + u8 val[3];
> +
> + error = elan_i2c_read_cmd(client,
> + iap ? ETP_I2C_IAP_VERSION_CMD :
> + ETP_I2C_FW_VERSION_CMD,
> + val);
> + if (error) {
> + dev_err(&client->dev, "failed to get %s version: %d\n",
> + iap ? "IAP" : "FW", error);
> + return error;
> + }
> +
> + *version = val[0];
> + return 0;
> +}
> +
> +static int elan_i2c_get_sm_version(struct i2c_client *client, u8 *version)
> +{
> + int error;
> + u8 val[3];
> +
> + error = elan_i2c_read_cmd(client, ETP_I2C_SM_VERSION_CMD, val);
> + if (error) {
> + dev_err(&client->dev, "failed to get SM version: %d\n", error);
> + return error;
> + }
> +
> + *version = val[0];
> + return 0;
> +}
> +
> +static int elan_i2c_get_product_id(struct i2c_client *client, u8 *id)
> +{
> + int error;
> + u8 val[3];
> +
> + error = elan_i2c_read_cmd(client, ETP_I2C_UNIQUEID_CMD, val);
> + if (error) {
> + dev_err(&client->dev, "failed to get product ID: %d\n", error);
> + return error;
> + }
> +
> + *id = val[0];
> + return 0;
> +}
> +
> +static int elan_i2c_get_checksum(struct i2c_client *client,
> + bool iap, u16 *csum)
> +{
> + int error;
> + u8 val[3];
> +
> + error = elan_i2c_read_cmd(client,
> + iap ? ETP_I2C_IAP_CHECKSUM_CMD :
> + ETP_I2C_FW_CHECKSUM_CMD,
> + val);
> + if (error) {
> + dev_err(&client->dev, "failed to get %s checksum: %d\n",
> + iap ? "IAP" : "FW", error);
> + return error;
> + }
> +
> + *csum = le16_to_cpup((__le16 *)val);
> + return 0;
> +}
> +
> +static int elan_i2c_get_max(struct i2c_client *client,
> + unsigned int *max_x, unsigned int *max_y)
> +{
> + int error;
> + u8 val[3];
> +
> + error = elan_i2c_read_cmd(client, ETP_I2C_MAX_X_AXIS_CMD, val);
> + if (error) {
> + dev_err(&client->dev, "failed to get X dimension: %d\n", error);
> + return error;
> + }
> +
> + *max_x = le16_to_cpup((__le16 *)val) & 0x0fff;
> +
> + error = elan_i2c_read_cmd(client, ETP_I2C_MAX_Y_AXIS_CMD, val);
> + if (error) {
> + dev_err(&client->dev, "failed to get Y dimension: %d\n", error);
> + return error;
> + }
> +
> + *max_y = le16_to_cpup((__le16 *)val) & 0x0fff;
> +
> + return 0;
> +}
> +
> +static int elan_i2c_get_resolution(struct i2c_client *client,
> + u8 *hw_res_x, u8 *hw_res_y)
> +{
> + int error;
> + u8 val[3];
> +
> + error = elan_i2c_read_cmd(client, ETP_I2C_RESOLUTION_CMD, val);
> + if (error) {
> + dev_err(&client->dev, "failed to get resolution: %d\n", error);
> + return error;
> + }
> +
> + *hw_res_x = val[0];
> + *hw_res_y = val[1];
> +
> + return 0;
> +}
> +
> +static int elan_i2c_get_num_traces(struct i2c_client *client,
> + unsigned int *x_traces,
> + unsigned int *y_traces)
> +{
> + int error;
> + u8 val[3];
> +
> + error = elan_i2c_read_cmd(client, ETP_I2C_XY_TRACENUM_CMD, val);
> + if (error) {
> + dev_err(&client->dev, "failed to get trace info: %d\n", error);
> + return error;
> + }
> +
> + *x_traces = val[0] - 1;
> + *y_traces = val[1] - 1;
> +
> + return 0;
> +}
> +
> +static int elan_i2c_iap_get_mode(struct i2c_client *client, enum tp_mode
> *mode)
> +{
> + int error;
> + u16 constant;
> + u8 val[3];
> +
> + error = elan_i2c_read_cmd(client, ETP_I2C_IAP_CTRL_CMD, val);
> + if (error) {
> + dev_err(&client->dev,
> + "failed to read iap control register: %d\n",
> + error);
> + return error;
> + }
> +
> + constant = le16_to_cpup((__le16 *)val);
> + dev_dbg(&client->dev, "iap control reg: 0x%04x.\n", constant);
> +
> + *mode = (constant & ETP_I2C_MAIN_MODE_ON) ? MAIN_MODE : IAP_MODE;
> +
> + return 0;
> +}
> +
> +static int elan_i2c_iap_reset(struct i2c_client *client)
> +{
> + int error;
> +
> + error = elan_i2c_write_cmd(client, ETP_I2C_IAP_RESET_CMD,
> + ETP_I2C_IAP_RESET);
> + if (error) {
> + dev_err(&client->dev, "cannot reset IC: %d\n", error);
> + return error;
> + }
> +
> + return 0;
> +}
> +
> +static int elan_i2c_set_flash_key(struct i2c_client *client)
> +{
> + int error;
> +
> + error = elan_i2c_write_cmd(client, ETP_I2C_IAP_CMD,
> + ETP_I2C_IAP_PASSWORD);
> + if (error) {
> + dev_err(&client->dev, "cannot set flash key: %d\n", error);
> + return error;
> + }
> +
> + return 0;
> +}
> +
> +static int elan_i2c_prepare_fw_update(struct i2c_client *client)
> +{
> + struct device *dev = &client->dev;
> + int error;
> + enum tp_mode mode;
> + u8 val[3];
> + u16 password;
> +
> + /* Get FW in which mode (IAP_MODE/MAIN_MODE) */
> + error = elan_i2c_iap_get_mode(client, &mode);
> + if (error)
> + return error;
> +
> + if (mode == IAP_MODE) {
> + /* Reset IC */
> + error = elan_i2c_iap_reset(client);
> + if (error)
> + return error;
> +
> + msleep(30);
> + }
> +
> + /* Set flash key*/
> + error = elan_i2c_set_flash_key(client);
> + if (error)
> + return error;
> +
> + /* Wait for F/W IAP initialization */
> + msleep(mode == MAIN_MODE ? 100 : 30);
> +
> + /* Check if we are in IAP mode or not */
> + error = elan_i2c_iap_get_mode(client, &mode);
> + if (error)
> + return error;
> +
> + if (mode == MAIN_MODE) {
> + dev_err(dev, "wrong mode: %d\n", mode);
> + return -EIO;
> + }
> +
> + /* Set flash key again */
> + error = elan_i2c_set_flash_key(client);
> + if (error)
> + return error;
> +
> + /* Wait for F/W IAP initialization */
> + msleep(30);
> +
> + /* read back to check we actually enabled successfully. */
> + error = elan_i2c_read_cmd(client, ETP_I2C_IAP_CMD, val);
> + if (error) {
> + dev_err(dev, "cannot read iap password: %d\n",
> + error);
> + return error;
> + }
> +
> + password = le16_to_cpup((__le16 *)val);
> + if (password != ETP_I2C_IAP_PASSWORD) {
> + dev_err(dev, "wrong iap password: 0x%X\n", password);
> + return -EIO;
> + }
> +
> + return 0;
> +}
> +
> +static int elan_i2c_write_fw_block(struct i2c_client *client,
> + const u8 *page, u16 checksum, int idx)
> +{
> + struct device *dev = &client->dev;
> + u8 page_store[ETP_FW_PAGE_SIZE + 4];
> + u8 val[3];
> + u16 result;
> + int ret, error;
> +
> + page_store[0] = ETP_I2C_IAP_REG_L;
> + page_store[1] = ETP_I2C_IAP_REG_H;
> + memcpy(&page_store[2], page, ETP_FW_PAGE_SIZE);
> + /* recode checksum at last two bytes */
> + put_unaligned_le16(checksum, &page_store[ETP_FW_PAGE_SIZE + 2]);
> +
> + ret = i2c_master_send(client, page_store, sizeof(page_store));
> + if (ret != sizeof(page_store)) {
> + error = ret < 0 ? ret : -EIO;
> + dev_err(dev, "Failed to write page %d: %d\n", idx, error);
> + return error;
> + }
> +
> + /* Wait for F/W to update one page ROM data. */
> + msleep(20);
> +
> + error = elan_i2c_read_cmd(client, ETP_I2C_IAP_CTRL_CMD, val);
> + if (error) {
> + dev_err(dev, "Failed to read IAP write result: %d\n", error);
> + return error;
> + }
> +
> + result = le16_to_cpup((__le16 *)val);
> + if (result & (ETP_FW_IAP_PAGE_ERR | ETP_FW_IAP_INTF_ERR)) {
> + dev_err(dev, "IAP reports failed write: %04hx\n",
> + result);
> + return -EIO;
> + }
> +
> + return 0;
> +}
> +
> +static int elan_i2c_finish_fw_update(struct i2c_client *client,
> + struct completion *completion)
> +{
> + struct device *dev = &client->dev;
> + long ret;
> + int error;
> + int len;
> + u8 buffer[ETP_I2C_INF_LENGTH];
> +
> + reinit_completion(completion);
> + enable_irq(client->irq);
> +
> + error = elan_i2c_write_cmd(client, ETP_I2C_STAND_CMD, ETP_I2C_RESET);
> + if (!error)
> + ret = wait_for_completion_interruptible_timeout(completion,
> + msecs_to_jiffies(300));
> + disable_irq(client->irq);
> +
> + if (error) {
> + dev_err(dev, "device reset failed: %d\n", error);
> + return error;
> + } else if (ret == 0) {
> + dev_err(dev, "timeout waiting for device reset\n");
> + return -ETIMEDOUT;
> + } else if (ret < 0) {
> + error = ret;
> + dev_err(dev, "error waiting for device reset: %d\n", error);
> + return error;
> + }
> +
> + len = i2c_master_recv(client, buffer, ETP_I2C_INF_LENGTH);
> + if (len != ETP_I2C_INF_LENGTH) {
> + error = len < 0 ? len : -EIO;
> + dev_err(dev, "failed to read INT signal: %d (%d)\n",
> + error, len);
> + return error;
> + }
> +
> + return 0;
> +}
> +
> +static int elan_i2c_get_report(struct i2c_client *client, u8 *report)
> +{
> + int len;
> +
> + len = i2c_master_recv(client, report, ETP_I2C_REPORT_LEN);
> + if (len < 0) {
> + dev_err(&client->dev, "failed to read report data: %d\n", len);
> + return len;
> + }
> +
> + if (len != ETP_I2C_REPORT_LEN) {
> + dev_err(&client->dev,
> + "wrong report length (%d vs %d expected)\n",
> + len, ETP_I2C_REPORT_LEN);
> + return -EIO;
> + }
> +
> + return 0;
> +}
> +
> +const struct elan_transport_ops elan_i2c_ops = {
> + .initialize = elan_i2c_initialize,
> + .sleep_control = elan_i2c_sleep_control,
> + .power_control = elan_i2c_power_control,
> + .set_mode = elan_i2c_set_mode,
> +
> + .calibrate = elan_i2c_calibrate,
> + .calibrate_result = elan_i2c_calibrate_result,
> +
> + .get_baseline_data = elan_i2c_get_baseline_data,
> +
> + .get_version = elan_i2c_get_version,
> + .get_sm_version = elan_i2c_get_sm_version,
> + .get_product_id = elan_i2c_get_product_id,
> + .get_checksum = elan_i2c_get_checksum,
> +
> + .get_max = elan_i2c_get_max,
> + .get_resolution = elan_i2c_get_resolution,
> + .get_num_traces = elan_i2c_get_num_traces,
> +
> + .iap_get_mode = elan_i2c_iap_get_mode,
> + .iap_reset = elan_i2c_iap_reset,
> +
> + .prepare_fw_update = elan_i2c_prepare_fw_update,
> + .write_fw_block = elan_i2c_write_fw_block,
> + .finish_fw_update = elan_i2c_finish_fw_update,
> +
> + .get_report = elan_i2c_get_report,
> +};
> diff --git a/drivers/input/mouse/elan_i2c_smbus.c
> b/drivers/input/mouse/elan_i2c_smbus.c
> new file mode 100644
> index 0000000..e58d82b
> --- /dev/null
> +++ b/drivers/input/mouse/elan_i2c_smbus.c
> @@ -0,0 +1,514 @@
> +/*
> + * Elan I2C/SMBus Touchpad driver - SMBus interface
> + *
> + * Copyright (c) 2013 ELAN Microelectronics Corp.
> + *
> + * Author: 林政維 (Duson Lin) <duson...@emc.com.tw>
> + * Version: 1.5.5
> + *
> + * Based on cyapa driver:
> + * copyright (c) 2011-2012 Cypress Semiconductor, Inc.
> + * copyright (c) 2011-2012 Google, Inc.
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License version 2 as published
> + * by the Free Software Foundation.
> + *
> + * Trademarks are the property of their respective owners.
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/i2c.h>
> +#include <linux/init.h>
> +#include <linux/kernel.h>
> +
> +#include "elan_i2c.h"
> +
> +/* Elan SMbus commands */
> +#define ETP_SMBUS_IAP_CMD 0x00
> +#define ETP_SMBUS_ENABLE_TP 0x20
> +#define ETP_SMBUS_SLEEP_CMD 0x21
> +#define ETP_SMBUS_IAP_PASSWORD_WRITE 0x29
> +#define ETP_SMBUS_IAP_PASSWORD_READ 0x80
> +#define ETP_SMBUS_WRITE_FW_BLOCK 0x2A
> +#define ETP_SMBUS_IAP_RESET_CMD 0x2B
> +#define ETP_SMBUS_RANGE_CMD 0xA0
> +#define ETP_SMBUS_FW_VERSION_CMD 0xA1
> +#define ETP_SMBUS_XY_TRACENUM_CMD 0xA2
> +#define ETP_SMBUS_SM_VERSION_CMD 0xA3
> +#define ETP_SMBUS_UNIQUEID_CMD 0xA3
> +#define ETP_SMBUS_RESOLUTION_CMD 0xA4
> +#define ETP_SMBUS_HELLOPACKET_CMD 0xA7
> +#define ETP_SMBUS_PACKET_QUERY 0xA8
> +#define ETP_SMBUS_IAP_VERSION_CMD 0xAC
> +#define ETP_SMBUS_IAP_CTRL_CMD 0xAD
> +#define ETP_SMBUS_IAP_CHECKSUM_CMD 0xAE
> +#define ETP_SMBUS_FW_CHECKSUM_CMD 0xAF
> +#define ETP_SMBUS_MAX_BASELINE_CMD 0xC3
> +#define ETP_SMBUS_MIN_BASELINE_CMD 0xC4
> +#define ETP_SMBUS_CALIBRATE_QUERY 0xC5
> +
> +#define ETP_SMBUS_REPORT_LEN 32
> +#define ETP_SMBUS_REPORT_OFFSET 2
> +#define ETP_SMBUS_HELLOPACKET_LEN 5
> +#define ETP_SMBUS_IAP_PASSWORD 0x1234
> +#define ETP_SMBUS_IAP_MODE_ON (1 << 6)
> +
> +static int elan_smbus_initialize(struct i2c_client *client)
> +{
> + u8 check[ETP_SMBUS_HELLOPACKET_LEN] = { 0x55, 0x55, 0x55, 0x55, 0x55 };
> + u8 values[ETP_SMBUS_HELLOPACKET_LEN] = { 0, 0, 0, 0, 0 };
> + int len, error;
> +
> + /* Get hello packet */
> + len = i2c_smbus_read_block_data(client,
> + ETP_SMBUS_HELLOPACKET_CMD, values);
> + if (len != ETP_SMBUS_HELLOPACKET_LEN) {
> + dev_err(&client->dev, "hello packet length fail: %d\n", len);
> + error = len < 0 ? len : -EIO;
> + return error;
> + }
> +
> + /* compare hello packet */
> + if (memcmp(values, check, ETP_SMBUS_HELLOPACKET_LEN)) {
> + dev_err(&client->dev, "hello packet fail [%*px]\n",
> + ETP_SMBUS_HELLOPACKET_LEN, values);
> + return -ENXIO;
> + }
> +
> + /* enable tp */
> + error = i2c_smbus_write_byte(client, ETP_SMBUS_ENABLE_TP);
> + if (error) {
> + dev_err(&client->dev, "failed to enable touchpad: %d\n", error);
> + return error;
> + }
> +
> + return 0;
> +}
> +
> +static int elan_smbus_set_mode(struct i2c_client *client, u8 mode)
> +{
> + u8 cmd[4] = { 0x00, 0x07, 0x00, mode };
> +
> + return i2c_smbus_write_block_data(client, ETP_SMBUS_IAP_CMD,
> + sizeof(cmd), cmd);
> +}
> +
> +static int elan_smbus_sleep_control(struct i2c_client *client, bool sleep)
> +{
> + if (sleep)
> + return i2c_smbus_write_byte(client, ETP_SMBUS_SLEEP_CMD);
> + else
> + return 0; /* XXX should we send ETP_SMBUS_ENABLE_TP here? */
> +}
> +
> +static int elan_smbus_power_control(struct i2c_client *client, bool enable)
> +{
> + return 0; /* A no-op */
> +}
> +
> +static int elan_smbus_calibrate(struct i2c_client *client)
> +{
> + u8 cmd[4] = { 0x00, 0x08, 0x00, 0x01 };
> +
> + return i2c_smbus_write_block_data(client, ETP_SMBUS_IAP_CMD,
> + sizeof(cmd), cmd);
> +}
> +
> +static int elan_smbus_calibrate_result(struct i2c_client *client, u8 *val)
> +{
> + int error;
> +
> + error = i2c_smbus_read_block_data(client,
> + ETP_SMBUS_CALIBRATE_QUERY, val);
> + if (error < 0)
> + return error;
> +
> + return 0;
> +}
> +
> +static int elan_smbus_get_baseline_data(struct i2c_client *client,
> + bool max_baseline, u8 *value)
> +{
> + int error;
> + u8 val[3];
> +
> + error = i2c_smbus_read_block_data(client,
> + max_baseline ?
> + ETP_SMBUS_MAX_BASELINE_CMD :
> + ETP_SMBUS_MIN_BASELINE_CMD,
> + val);
> + if (error < 0)
> + return error;
> +
> + *value = be16_to_cpup((__be16 *)val);
> +
> + return 0;
> +}
> +
> +static int elan_smbus_get_version(struct i2c_client *client,
> + bool iap, u8 *version)
> +{
> + int error;
> + u8 val[3];
> +
> + error = i2c_smbus_read_block_data(client,
> + iap ? ETP_SMBUS_IAP_VERSION_CMD :
> + ETP_SMBUS_FW_VERSION_CMD,
> + val);
> + if (error < 0) {
> + dev_err(&client->dev, "failed to get %s version: %d\n",
> + iap ? "IAP" : "FW", error);
> + return error;
> + }
> +
> + *version = val[2];
> + return 0;
> +}
> +
> +static int elan_smbus_get_sm_version(struct i2c_client *client, u8 *version)
> +{
> + int error;
> + u8 val[3];
> +
> + error = i2c_smbus_read_block_data(client,
> + ETP_SMBUS_SM_VERSION_CMD, val);
> + if (error < 0) {
> + dev_err(&client->dev, "failed to get SM version: %d\n", error);
> + return error;
> + }
> +
> + *version = val[0]; /* XXX Why 0 and not 2 as in IAP/FW versions? */
> + return 0;
> +}
> +
> +static int elan_smbus_get_product_id(struct i2c_client *client, u8 *id)
> +{
> + int error;
> + u8 val[3];
> +
> + error = i2c_smbus_read_block_data(client,
> + ETP_SMBUS_UNIQUEID_CMD, val);
> + if (error < 0) {
> + dev_err(&client->dev, "failed to get product ID: %d\n", error);
> + return error;
> + }
> +
> + *id = val[1];
> + return 0;
> +}
> +
> +static int elan_smbus_get_checksum(struct i2c_client *client,
> + bool iap, u16 *csum)
> +{
> + int error;
> + u8 val[3];
> +
> + error = i2c_smbus_read_block_data(client,
> + iap ? ETP_SMBUS_FW_CHECKSUM_CMD :
> + ETP_SMBUS_IAP_CHECKSUM_CMD,
> + val);
> + if (error < 0) {
> + dev_err(&client->dev, "failed to get %s checksum: %d\n",
> + iap ? "IAP" : "FW", error);
> + return error;
> + }
> +
> + *csum = be16_to_cpup((__be16 *)val);
> + return 0;
> +}
> +
> +static int elan_smbus_get_max(struct i2c_client *client,
> + unsigned int *max_x, unsigned int *max_y)
> +{
> + int error;
> + u8 val[3];
> +
> + error = i2c_smbus_read_block_data(client, ETP_SMBUS_RANGE_CMD, val);
> + if (error) {
> + dev_err(&client->dev, "failed to get dimensions: %d\n", error);
> + return error;
> + }
> +
> + *max_x = (0x0f & val[0]) << 8 | val[1];
> + *max_y = (0xf0 & val[0]) << 4 | val[2];
> +
> + return 0;
> +}
> +
> +static int elan_smbus_get_resolution(struct i2c_client *client,
> + u8 *hw_res_x, u8 *hw_res_y)
> +{
> + int error;
> + u8 val[3];
> +
> + error = i2c_smbus_read_block_data(client,
> + ETP_SMBUS_RESOLUTION_CMD, val);
> + if (error) {
> + dev_err(&client->dev, "failed to get resolution: %d\n", error);
> + return error;
> + }
> +
> + *hw_res_x = val[1] & 0x0F;
> + *hw_res_y = (val[1] & 0xF0) >> 4;
> +
> + return 0;
> +}
> +
> +static int elan_smbus_get_num_traces(struct i2c_client *client,
> + unsigned int *x_traces,
> + unsigned int *y_traces)
> +{
> + int error;
> + u8 val[3];
> +
> + error = i2c_smbus_read_block_data(client,
> + ETP_SMBUS_XY_TRACENUM_CMD, val);
> + if (error) {
> + dev_err(&client->dev, "failed to get trace info: %d\n", error);
> + return error;
> + }
> +
> + *x_traces = val[1] - 1;
> + *y_traces = val[2] - 1;
> +
> + return 0;
> +}
> +
> +static int elan_smbus_iap_get_mode(struct i2c_client *client,
> + enum tp_mode *mode)
> +{
> + int error;
> + u16 constant;
> + u8 val[3];
> +
> + error = i2c_smbus_read_block_data(client, ETP_SMBUS_IAP_CTRL_CMD, val);
> + if (error < 0) {
> + dev_err(&client->dev, "failed to read iap ctrol register: %d\n",
> + error);
> + return error;
> + }
> +
> + constant = be16_to_cpup((__be16 *)val);
> + dev_dbg(&client->dev, "iap control reg: 0x%04x.\n", constant);
> +
> + *mode = (constant & ETP_SMBUS_IAP_MODE_ON) ? IAP_MODE : MAIN_MODE;
> +
> + return 0;
> +}
> +
> +static int elan_smbus_iap_reset(struct i2c_client *client)
> +{
> + int error;
> +
> + error = i2c_smbus_write_byte(client, ETP_SMBUS_IAP_RESET_CMD);
> + if (error) {
> + dev_err(&client->dev, "cannot reset IC: %d\n", error);
> + return error;
> + }
> +
> + return 0;
> +}
> +
> +static int elan_smbus_set_flash_key(struct i2c_client *client)
> +{
> + int error;
> + u8 cmd[4] = { 0x00, 0x0B, 0x00, 0x5A };
> +
> + error = i2c_smbus_write_block_data(client, ETP_SMBUS_IAP_CMD,
> + sizeof(cmd), cmd);
> + if (error) {
> + dev_err(&client->dev, "cannot set flash key: %d\n", error);
> + return error;
> + }
> +
> + return 0;
> +}
> +
> +static int elan_smbus_prepare_fw_update(struct i2c_client *client)
> +{
> + struct device *dev = &client->dev;
> + int len;
> + int error;
> + enum tp_mode mode;
> + u8 val[3];
> + u8 cmd[4] = {0x0F, 0x78, 0x00, 0x06};
> + u16 password;
> +
> + /* Get FW in which mode (IAP_MODE/MAIN_MODE) */
> + error = elan_smbus_iap_get_mode(client, &mode);
> + if (error)
> + return error;
> +
> + if (mode == MAIN_MODE) {
> +
> + /* set flash key */
> + error = elan_smbus_set_flash_key(client);
> + if (error)
> + return error;
> +
> + /* write iap password */
> + if (i2c_smbus_write_byte(client,
> + ETP_SMBUS_IAP_PASSWORD_WRITE) < 0) {
> + dev_err(dev, "cannot write iap password\n");
> + return -EIO;
> + }
> +
> + error = i2c_smbus_write_block_data(client, ETP_SMBUS_IAP_CMD,
> + sizeof(cmd), cmd);
> + if (error) {
> + dev_err(dev, "failed to write iap password: %d\n",
> + error);
> + return error;
> + }
> +
> + /*
> + * Read back password to make sure we enabled flash
> + * successfully.
> + */
> + len = i2c_smbus_read_block_data(client,
> + ETP_SMBUS_IAP_PASSWORD_READ,
> + val);
> + if (len != sizeof(ETP_SMBUS_IAP_PASSWORD)) {
> + error = len < 0 ? len : -EIO;
> + dev_err(dev, "failed to read iap password: %d\n",
> + error);
> + return error;
> + }
> +
> + password = be16_to_cpup((__be16 *)val);
> + if (password != ETP_SMBUS_IAP_PASSWORD) {
> + dev_err(dev, "wrong iap password = 0x%X\n", password);
> + return -EIO;
> + }
> +
> + /* Wait 30ms for MAIN_MODE change to IAP_MODE */
> + msleep(30);
> + }
> +
> + error = elan_smbus_set_flash_key(client);
> + if (error)
> + return error;
> +
> + /* Reset IC */
> + error = elan_smbus_iap_reset(client);
> + if (error)
> + return error;
> +
> + return 0;
> +}
> +
> +
> +static int elan_smbus_write_fw_block(struct i2c_client *client,
> + const u8 *page, u16 checksum, int idx)
> +{
> + struct device *dev = &client->dev;
> + int error;
> + u16 result;
> + u8 val[3];
> +
> + /*
> + * Due to the limitation of smbus protocol limiting
> + * transfer to 32 bytes at a time, we must split block
> + * in 2 transfers.
> + */
> + error = i2c_smbus_write_block_data(client,
> + ETP_SMBUS_WRITE_FW_BLOCK,
> + ETP_FW_PAGE_SIZE / 2,
> + page);
> + if (error) {
> + dev_err(dev, "Failed to write page %d (part %d): %d\n",
> + idx, 1, error);
> + return error;
> + }
> +
> + error = i2c_smbus_write_block_data(client,
> + ETP_SMBUS_WRITE_FW_BLOCK,
> + ETP_FW_PAGE_SIZE / 2,
> + page + ETP_FW_PAGE_SIZE / 2);
> + if (error) {
> + dev_err(dev, "Failed to write page %d (part %d): %d\n",
> + idx, 2, error);
> + return error;
> + }
> +
> +
> + /* Wait for F/W to update one page ROM data. */
> + usleep_range(8000, 10000);
> +
> + error = i2c_smbus_read_block_data(client,
> + ETP_SMBUS_IAP_CTRL_CMD, val);
> + if (error < 0) {
> + dev_err(dev, "Failed to read IAP write result: %d\n",
> + error);
> + return error;
> + }
> +
> + result = be16_to_cpup((__be16 *)val);
> + if (result & (ETP_FW_IAP_PAGE_ERR | ETP_FW_IAP_INTF_ERR)) {
> + dev_err(dev, "IAP reports failed write: %04hx\n",
> + result);
> + return -EIO;
> + }
> +
> + return 0;
> +}
> +
> +static int elan_smbus_get_report(struct i2c_client *client, u8 *report)
> +{
> + int len;
> +
> + len = i2c_smbus_read_block_data(client,
> + ETP_SMBUS_PACKET_QUERY,
> + &report[ETP_SMBUS_REPORT_OFFSET]);
> + if (len < 0) {
> + dev_err(&client->dev, "failed to read report data: %d\n", len);
> + return len;
> + }
> +
> + if (len != ETP_SMBUS_REPORT_LEN) {
> + dev_err(&client->dev,
> + "wrong report length (%d vs %d expected)\n",
> + len, ETP_SMBUS_REPORT_LEN);
> + return -EIO;
> + }
> +
> + return 0;
> +}
> +
> +static int elan_smbus_finish_fw_update(struct i2c_client *client,
> + struct completion *fw_completion)
> +{
> + /* No special handling unlike I2C transport */
> + return 0;
> +}
> +
> +const struct elan_transport_ops elan_smbus_ops = {
> + .initialize = elan_smbus_initialize,
> + .sleep_control = elan_smbus_sleep_control,
> + .power_control = elan_smbus_power_control,
> + .set_mode = elan_smbus_set_mode,
> +
> + .calibrate = elan_smbus_calibrate,
> + .calibrate_result = elan_smbus_calibrate_result,
> +
> + .get_baseline_data = elan_smbus_get_baseline_data,
> +
> + .get_version = elan_smbus_get_version,
> + .get_sm_version = elan_smbus_get_sm_version,
> + .get_product_id = elan_smbus_get_product_id,
> + .get_checksum = elan_smbus_get_checksum,
> +
> + .get_max = elan_smbus_get_max,
> + .get_resolution = elan_smbus_get_resolution,
> + .get_num_traces = elan_smbus_get_num_traces,
> +
> + .iap_get_mode = elan_smbus_iap_get_mode,
> + .iap_reset = elan_smbus_iap_reset,
> +
> + .prepare_fw_update = elan_smbus_prepare_fw_update,
> + .write_fw_block = elan_smbus_write_fw_block,
> + .finish_fw_update = elan_smbus_finish_fw_update,
> +
> + .get_report = elan_smbus_get_report,
> +};
--
Dmitry
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
