Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161, update
the phy driver to not use the reg property to access the sysconfig register
offsets.
This is because other phy's (miphy28, miphy365) have a combination of memory
mapped
registers and sysconfig control regs, and we shouldn't be mixing address spaces
in the reg property. In addition we would ideally like the sysconfig offsets to
be
passed via DT in a uniform way. This new method will also allow us to support
devices
which have sysconfig registers in different banks more easily and it is also
analagous
to how keystone and bcm7745 platforms pass there syscon offsets in DT.
This breaks DT compatibility, but this platform is considered WIP, and is only
used by a few developers who are upstreaming support for it.
Signed-off-by: Peter Griffin <peter.grif...@linaro.org>
---
.../devicetree/bindings/phy/phy-stih407-usb.txt | 10 ++-------
drivers/phy/phy-stih407-usb.c | 25 ++++++++++++----------
2 files changed, 16 insertions(+), 19 deletions(-)
diff --git a/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt
b/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt
index 1ef8228..de6a706 100644
--- a/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt
+++ b/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt
@@ -5,10 +5,7 @@ host controllers (when controlling usb2/1.1 devices) available
on STiH407 SoC fa
Required properties:
- compatible : should be "st,stih407-usb2-phy"
-- reg : contain the offset and length of the system
configuration registers
- used as glue logic to control & parameter phy
-- reg-names : the names of the system configuration registers in
"reg", should be "param" and "reg"
-- st,syscfg : sysconfig register to manage phy parameter at driver
level
+- st,syscfg : phandle of sysconfig bank plus integer array
containing phyparam and phyctrl register offsets
- resets : list of phandle and reset specifier pairs. There
should be two entries, one
for the whole phy and one for the port
- reset-names : list of reset signal names. Should be "global" and
"port"
@@ -19,11 +16,8 @@ Example:
usb2_picophy0: usbpicophy@f8 {
compatible = "st,stih407-usb2-phy";
- reg = <0xf8 0x04>, /* syscfg 5062 */
- <0xf4 0x04>; /* syscfg 5061 */
- reg-names = "param", "ctrl";
#phy-cells = <0>;
- st,syscfg = <&syscfg_core>;
+ st,syscfg = <&syscfg_core 0x100 0xf4>;
resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
<&picophyreset STIH407_PICOPHY0_RESET>;
reset-names = "global", "port";
diff --git a/drivers/phy/phy-stih407-usb.c b/drivers/phy/phy-stih407-usb.c
index 42428d4..24d5e2a 100644
--- a/drivers/phy/phy-stih407-usb.c
+++ b/drivers/phy/phy-stih407-usb.c
@@ -22,6 +22,9 @@
#include <linux/mfd/syscon.h>
#include <linux/phy/phy.h>
+#define PHYPARAM_REG 1
+#define PHYCTRL_REG 2
+
/* Default PHY_SEL and REFCLKSEL configuration */
#define STIH407_USB_PICOPHY_CTRL_PORT_CONF 0x6
#define STIH407_USB_PICOPHY_CTRL_PORT_MASK 0x1f
@@ -93,7 +96,7 @@ static int stih407_usb2_picophy_probe(struct platform_device
*pdev)
struct device_node *np = dev->of_node;
struct phy_provider *phy_provider;
struct phy *phy;
- struct resource *res;
+ int ret;
phy_dev = devm_kzalloc(dev, sizeof(*phy_dev), GFP_KERNEL);
if (!phy_dev)
@@ -123,19 +126,19 @@ static int stih407_usb2_picophy_probe(struct
platform_device *pdev)
return PTR_ERR(phy_dev->regmap);
}
- res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ctrl");
- if (!res) {
- dev_err(dev, "No ctrl reg found\n");
- return -ENXIO;
+ ret = of_property_read_u32_index(np, "st,syscfg", PHYPARAM_REG,
+ &phy_dev->param);
+ if (ret) {
+ dev_err(dev, "can't get phyparam offset (%d)\n", ret);
+ return ret;
}
- phy_dev->ctrl = res->start;
- res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "param");
- if (!res) {
- dev_err(dev, "No param reg found\n");
- return -ENXIO;
+ ret = of_property_read_u32_index(np, "st,syscfg", PHYCTRL_REG,
+ &phy_dev->ctrl);
+ if (ret) {
+ dev_err(dev, "can't get phyctrl offset (%d)\n", ret);
+ return ret;
}
- phy_dev->param = res->start;
phy = devm_phy_create(dev, NULL, &stih407_usb2_picophy_data, NULL);
if (IS_ERR(phy)) {
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
