Hi Kishon,
On Tue, 23 Jun 2015 17:28:47 +0530
Kishon Vijay Abraham I <kis...@ti.com> wrote:
> Deprecate using phy-omap-control driver to power on/off the PHY and
> use *syscon* framework to do the same.
>
> Signed-off-by: Kishon Vijay Abraham I <kis...@ti.com>
> ---
> Documentation/devicetree/bindings/phy/ti-phy.txt | 10 ++-
> drivers/phy/phy-ti-pipe3.c | 91
> ++++++++++++++++++----
> 2 files changed, 86 insertions(+), 15 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt
> b/Documentation/devicetree/bindings/phy/ti-phy.txt
> index f0f5537..d3ad3bf 100644
> --- a/Documentation/devicetree/bindings/phy/ti-phy.txt
> +++ b/Documentation/devicetree/bindings/phy/ti-phy.txt
> @@ -77,8 +77,6 @@ Required properties:
> * "div-clk" - apll clock
>
> Optional properties:
> - - ctrl-module : phandle of the control module used by PHY driver to power on
> - the PHY.
> - id: If there are multiple instance of the same type, in order to
> differentiate between each instance "id" can be used (e.g., multi-lane
> PCIe
> PHY). If "id" is not provided, it is set to default value of '1'.
> @@ -86,6 +84,14 @@ Optional properties:
> CTRL_CORE_SMA_SW_0 register and register offset to the CTRL_CORE_SMA_SW_0
> register that contains the SATA_PLL_SOFT_RESET bit. Only valid for
> sata_phy.
>
> +Deprecated properties:
> + - ctrl-module : phandle of the control module used by PHY driver to power on
> + the PHY.
> +
> +Recommended properies:
> + - syscon-phy-power : phandle/offset pair. Phandle to the system control
> + module and the register offset to power on/off the PHY.
> +
> This is usually a subnode of ocp2scp to which it is connected.
>
> usb3phy@4a084400 {
> diff --git a/drivers/phy/phy-ti-pipe3.c b/drivers/phy/phy-ti-pipe3.c
> index d784426..78bac00 100644
> --- a/drivers/phy/phy-ti-pipe3.c
> +++ b/drivers/phy/phy-ti-pipe3.c
> @@ -56,6 +56,15 @@
>
> #define SATA_PLL_SOFT_RESET BIT(18)
>
> +#define PIPE3_PHY_PWRCTL_CLK_CMD_MASK 0x003FC000
> +#define PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT 14
> +
> +#define PIPE3_PHY_PWRCTL_CLK_FREQ_MASK 0xFFC00000
> +#define PIPE3_PHY_PWRCTL_CLK_FREQ_SHIFT 22
> +
> +#define PIPE3_PHY_TX_RX_POWERON 0x3
> +#define PIPE3_PHY_TX_RX_POWEROFF 0x0
> +
> /*
> * This is an Empirical value that works, need to confirm the actual
> * value required for the PIPE3PHY_PLL_CONFIGURATION2.PLL_IDLE status
> @@ -86,8 +95,10 @@ struct ti_pipe3 {
> struct clk *refclk;
> struct clk *div_clk;
> struct pipe3_dpll_map *dpll_map;
> + struct regmap *phy_power_syscon; /* ctrl. reg. acces */
> struct regmap *dpll_reset_syscon; /* ctrl. reg. acces */
> unsigned int dpll_reset_reg; /* reg. index within syscon */
> + unsigned int power_reg; /* power reg. index within syscon */
> bool sata_refclk_enabled;
> };
>
> @@ -144,18 +155,49 @@ static void ti_pipe3_disable_clocks(struct ti_pipe3
> *phy);
>
> static int ti_pipe3_power_off(struct phy *x)
> {
> + u32 val;
> + int ret;
> struct ti_pipe3 *phy = phy_get_drvdata(x);
>
> - omap_control_phy_power(phy->control_dev, 0);
> + if (phy->phy_power_syscon) {
> + val = PIPE3_PHY_TX_RX_POWEROFF <<
> + PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT;
> +
> + ret = regmap_update_bits(phy->phy_power_syscon, phy->power_reg,
> + PIPE3_PHY_PWRCTL_CLK_CMD_MASK, val);
> + if (ret < 0)
> + return ret;
> + } else {
> + omap_control_phy_power(phy->control_dev, 0);
> + }
>
> return 0;
> }
>
> static int ti_pipe3_power_on(struct phy *x)
> {
> + u32 val;
> + u32 mask;
> + int ret;
> + unsigned long rate;
> struct ti_pipe3 *phy = phy_get_drvdata(x);
>
> - omap_control_phy_power(phy->control_dev, 1);
> + if (phy->phy_power_syscon) {
> + rate = clk_get_rate(phy->sys_clk);
what if clk_get_rate() returns 0?
> + rate = rate / 1000000;
> + mask = OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_MASK |
> + OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_MASK;
> + val = PIPE3_PHY_TX_RX_POWERON <<
> + PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT;
> + val |= rate << OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_SHIFT;
> +
> + ret = regmap_update_bits(phy->phy_power_syscon, phy->power_reg,
> + mask, val);
> + if (ret < 0)
> + return ret;
> + } else {
> + omap_control_phy_power(phy->control_dev, 1);
> + }
>
> return 0;
> }
> @@ -417,19 +459,42 @@ static int ti_pipe3_probe(struct platform_device *pdev)
> phy->div_clk = ERR_PTR(-ENODEV);
> }
>
> - control_node = of_parse_phandle(node, "ctrl-module", 0);
> - if (!control_node) {
> - dev_err(&pdev->dev, "Failed to get control device phandle\n");
> - return -EINVAL;
> - }
> + phy->phy_power_syscon = syscon_regmap_lookup_by_phandle(node,
> + "syscon-phy-power");
> + if (IS_ERR(phy->phy_power_syscon)) {
> + dev_info(&pdev->dev,
> + "can't get syscon-phy-power, using control device\n");
dev_dbg()? as we don't want to annoy old DT users?
> + phy->phy_power_syscon = NULL;
> +
> + control_node = of_parse_phandle(node, "ctrl-module", 0);
> + if (!control_node) {
> + dev_err(&pdev->dev,
> + "Failed to get control device phandle\n");
> + return -EINVAL;
> + }
>
> - control_pdev = of_find_device_by_node(control_node);
> - if (!control_pdev) {
> - dev_err(&pdev->dev, "Failed to get control device\n");
> - return -EINVAL;
> - }
> + control_pdev = of_find_device_by_node(control_node);
> + if (!control_pdev) {
> + dev_err(&pdev->dev, "Failed to get control device\n");
> + return -EINVAL;
> + }
>
> - phy->control_dev = &control_pdev->dev;
> + phy->control_dev = &control_pdev->dev;
> + } else {
> + phy->sys_clk = devm_clk_get(phy->dev, "sysclk");
> + if (IS_ERR(phy->sys_clk)) {
> + dev_err(&pdev->dev, "unable to get sysclk\n");
> + return -EINVAL;
> + }
we're already doing this at another place in pipe3_probe. Let's do it at one
place.
> +
> + if (of_property_read_u32_index(node,
> + "syscon-phy-power", 1,
> + &phy->power_reg)) {
> + dev_err(&pdev->dev,
> + "couldn't get power reg. offset\n");
> + return -EINVAL;
> + }
> + }
>
> platform_set_drvdata(pdev, phy);
> pm_runtime_enable(phy->dev);
> --
> 1.7.9.5
>
cheers,
-roger
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
