On Fri, Nov 13, 2015 at 04:02:23PM +0530, Anurag Kumar Vulisha wrote:
> In SATA, speed negotiation happens with OOB(Out of Band) signals. These OOB
> signal timing values are configured through vendor specific registers in the
> SATA controller. These OOB timings depends on the generator and detector clock
> frequency, which varies from board to board (ex: ep108, zcu102 and zc1751 has
> different clock frequencies).
Could you calculate the timings based on the frequency instead?
> Since to make ahci_ceva driver generic, it would be better to move these
> settings to the device-tree node and read them from driver.
>
> This patch does the same.
>
> Signed-off-by: Anurag Kumar Vulisha <anura...@xilinx.com>
> ---
> .../devicetree/bindings/ata/ahci-ceva.txt | 38 +++++++++
> drivers/ata/ahci_ceva.c | 84
> ++++++++++++++------
> 2 files changed, 99 insertions(+), 23 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/ata/ahci-ceva.txt
> b/Documentation/devicetree/bindings/ata/ahci-ceva.txt
> index 7ca8b97..66fcd10 100644
> --- a/Documentation/devicetree/bindings/ata/ahci-ceva.txt
> +++ b/Documentation/devicetree/bindings/ata/ahci-ceva.txt
> @@ -5,6 +5,36 @@ Required properties:
> - compatible: Compatibility string. Must be 'ceva,ahci-1v84'.
> - clocks: Input clock specifier. Refer to common clock bindings.
> - interrupts: Interrupt specifier. Refer to interrupt binding.
> + - ceva,p0-cominit-params: OOB timing value for COMINIT parameter for
> port 0.
> + - ceva,p1-cominit-params: OOB timing value for COMINIT parameter for
> port 1.
This doesn't really scale when you have more than 2 ports. Given that
you know the length for each port, just make it a single property (i.e.
an array of ports).
> + The fields for the above parameter must be as shown
> below:
> + ceva,phy-cominit-params = /bits/ 8 <CIBGMN CIBGMX CIBGN
> CINMP>;
> + CINMP : COMINIT Negate Minimum Period.
> + CIBGN : COMINIT Burst Gap Nominal.
> + CIBGMX: COMINIT Burst Gap Maximum.
> + CIBGMN: COMINIT Burst Gap Minimum.
> + - ceva,p0-comwake-params: OOB timing value for COMWAKE parameter for
> port 0.
> + - ceva,p1-comwake-params: OOB timing value for COMWAKE parameter for
> port 1.
> + The fields for the above parameter must be as shown
> below:
> + ceva,phy-comwake-params = /bits/ 8 <CWBGMN CWBGMX CWBGN
> CWNMP>;
> + CWBGMN: COMWAKE Burst Gap Minimum.
> + CWBGMX: COMWAKE Burst Gap Maximum.
> + CWBGN: COMWAKE Burst Gap Nominal.
> + CWNMP: COMWAKE Negate Minimum Period.
> + - ceva,p0-burst-params: Burst timing value for COM parameter for port 0.
> + - ceva,p1-burst-params: Burst timing value for COM parameter for port 1.
> + The fields for the above parameter must be as shown
> below:
> + ceva,phy-burst-params = /bits/ 8 <BMX BNM SFD PTST>;
> + BMX: COM Burst Maximum.
> + BNM: COM Burst Nominal.
> + SFD: Signal Failure Detection value.
> + PTST: Partial to Slumber timer value.
> + - ceva,p0-retry-params: Retry interval timing value for port 0.
> + - ceva,p1-retry-params: Retry interval timing value for port 1.
> + The fields for the above parameter must be as shown
> below:
> + ceva,phy-retry-params = /bits/ 16 <RIT RCT>;
> + RIT: Retry Interval Timer.
> + RCT: Rate Change Timer.
>
> Optional properties:
> - ceva,broken-gen2: limit to gen1 speed instead of gen2.
> @@ -17,4 +47,12 @@ Examples:
> interrupts = <0 133 4>;
> clocks = <&clkc SATA_CLK_ID>;
> ceva,broken-gen2;
> + ceva,p0-cominit-params = /bits/ 8 <0x0F 0x25 0x18 0x29>;
> + ceva,p0-comwake-params = /bits/ 8 <0x04 0x0B 0x08 0x0F>;
> + ceva,p0-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>;
> + ceva,p0-retry-params = /bits/ 16 <0x0216 0x7F06>;
> + ceva,p1-cominit-params = /bits/ 8 <0x0F 0x25 0x18 0x29>;
> + ceva,p1-comwake-params = /bits/ 8 <0x04 0x0B 0x08 0x0F>;
> + ceva,p1-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>;
> + ceva,p1-retry-params = /bits/ 16 <0x0216 0x7F06>;
> };
> diff --git a/drivers/ata/ahci_ceva.c b/drivers/ata/ahci_ceva.c
> index 207649d..59de2ca 100644
> --- a/drivers/ata/ahci_ceva.c
> +++ b/drivers/ata/ahci_ceva.c
> @@ -50,21 +50,6 @@
> #define PPCFG_PSS_EN (1 << 29)
> #define PPCFG_ESDF_EN (1 << 31)
>
> -#define PP2C_CIBGMN 0x0F
> -#define PP2C_CIBGMX (0x25 << 8)
> -#define PP2C_CIBGN (0x18 << 16)
> -#define PP2C_CINMP (0x29 << 24)
> -
> -#define PP3C_CWBGMN 0x04
> -#define PP3C_CWBGMX (0x0B << 8)
> -#define PP3C_CWBGN (0x08 << 16)
> -#define PP3C_CWNMP (0x0F << 24)
> -
> -#define PP4C_BMX 0x0a
> -#define PP4C_BNM (0x08 << 8)
> -#define PP4C_SFD (0x4a << 16)
> -#define PP4C_PTST (0x06 << 24)
> -
> #define PP5C_RIT 0x60216
> #define PP5C_RCT (0x7f0 << 20)
>
> @@ -87,6 +72,11 @@
>
> struct ceva_ahci_priv {
> struct platform_device *ahci_pdev;
> + /* Port Phy2Cfg Register */
> + u32 pp2c[NR_PORTS];
> + u32 pp3c[NR_PORTS];
> + u32 pp4c[NR_PORTS];
> + u32 pp5c[NR_PORTS];
> int flags;
> };
>
> @@ -131,20 +121,16 @@ static void ahci_ceva_setup(struct ahci_host_priv
> *hpriv)
> writel(tmp, mmio + AHCI_VEND_PPCFG);
>
> /* Phy Control OOB timing parameters COMINIT */
> - tmp = PP2C_CIBGMN | PP2C_CIBGMX | PP2C_CIBGN | PP2C_CINMP;
> - writel(tmp, mmio + AHCI_VEND_PP2C);
> + writel(cevapriv->pp2c[i], mmio + AHCI_VEND_PP2C);
>
> /* Phy Control OOB timing parameters COMWAKE */
> - tmp = PP3C_CWBGMN | PP3C_CWBGMX | PP3C_CWBGN | PP3C_CWNMP;
> - writel(tmp, mmio + AHCI_VEND_PP3C);
> + writel(cevapriv->pp3c[i], mmio + AHCI_VEND_PP3C);
>
> /* Phy Control Burst timing setting */
> - tmp = PP4C_BMX | PP4C_BNM | PP4C_SFD | PP4C_PTST;
> - writel(tmp, mmio + AHCI_VEND_PP4C);
> + writel(cevapriv->pp4c[i], mmio + AHCI_VEND_PP4C);
>
> /* Rate Change Timer and Retry Interval Timer setting */
> - tmp = PP5C_RIT | PP5C_RCT;
> - writel(tmp, mmio + AHCI_VEND_PP5C);
> + writel(cevapriv->pp5c[i], mmio + AHCI_VEND_PP5C);
>
> /* Rx Watermark setting */
> tmp = PTC_RX_WM_VAL | PTC_RSVD;
> @@ -187,6 +173,58 @@ static int ceva_ahci_probe(struct platform_device *pdev)
> if (of_property_read_bool(np, "ceva,broken-gen2"))
> cevapriv->flags = CEVA_FLAG_BROKEN_GEN2;
>
> + /* Read OOB timing value for COMINIT from device-tree */
> + if (of_property_read_u8_array(np, "ceva,p0-cominit-params",
> + (u8 *)&cevapriv->pp2c[0], 4) < 0) {
> + dev_warn(dev, "ceva,p0-cominit-params property not defined\n");
I'd really like to move all the error prints into the of_property_*
functions instead, but then we'd probably need *_optional variants to
avoid spewing to the console.
Rob
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
