On Tue, Dec 29, 2015 at 06:48:55PM -0700, Gilad Avidov wrote:
> Add supports for ethernet controller HW on Qualcomm Technologies, Inc. SoC.
> This driver supports the following features:
> 1) Checksum offload.
> 2) Runtime power management support.
> 3) Interrupt coalescing support.
> 4) SGMII phy.
> 5) SGMII direct connection without external phy.
>
> Based on a driver by Niranjana Vishwanathapura
> <nvish...@codeaurora.org>.
[...]
> diff --git a/Documentation/devicetree/bindings/net/qcom-emac.txt
> b/Documentation/devicetree/bindings/net/qcom-emac.txt
> new file mode 100644
> index 0000000..8d58a40
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/qcom-emac.txt
> @@ -0,0 +1,68 @@
> +Qualcomm EMAC Gigabit Ethernet Controller
> +
> +Required properties:
> +- cell-index : EMAC controller instance number.
> +- compatible : Should be "qcom,emac".
This should be more specific with the SOC name.
> +- reg : Offset and length of the register regions for the device
> +- reg-names : Register region names referenced in 'reg' above.
> + Required register resource entries are:
> + "base" : EMAC controller base register block.
> + "csr" : EMAC wrapper register block.
> + Optional register resource entries are:
> + "ptp" : EMAC PTP (1588) register block.
> + Required if 'qcom,emac-tstamp-en' is present.
> + "sgmii" : EMAC SGMII PHY register block.
> +- interrupts : Interrupt numbers used by this controller
> +- interrupt-names : Interrupt resource names referenced in 'interrupts'
> above.
> + Required interrupt resource entries are:
> + "emac_core0" : EMAC core0 interrupt.
> + "sgmii_irq" : EMAC SGMII interrupt.
> +- qcom,emac-gpio-mdc : GPIO pin number of the MDC line of MDIO bus.
> +- qcom,emac-gpio-mdio : GPIO pin number of the MDIO line of MDIO bus.
Use the standard binding for GPIO controlled MDIO bus.
> +- phy-addr : Specifies phy address on MDIO bus.
> + Required if the optional property "qcom,no-external-phy"
> + is not specified.
Don't you think you will need to know the specific phy device or other
properties of the phy?
> +
> +Optional properties:
> +- qcom,emac-tstamp-en : Enables the PTP (1588) timestamping feature.
> + Include this only if PTP (1588) timestamping
> + feature is needed. If included, "ptp" register
> + base should be specified.
Isn't this a user enabled feature if the h/w supports it?
> +- mac-address : The 6-byte MAC address. If present, it is the
> + default MAC address.
> +- qcom,no-external-phy : Indicates there is no external PHY connected to
> + EMAC. Include this only if the EMAC is directly
> + connected to the peer end without EPHY.
> +- qcom,emac-ptp-grandmaster : Enable the PTP (1588) grandmaster mode.
> + Include this only if PTP (1588) is configured as
> + grandmaster.
> +- qcom,emac-ptp-frac-ns-adj : The vector table to adjust the fractional ns
> per
> + RTC clock cycle.
> + Include this only if there is accuracy loss of
> + fractional ns per RTC clock cycle. For individual
> + table entry, the first field indicates the RTC
> + reference clock rate. The second field indicates
> + the number of adjustment in 2 ^ -26 ns.
> +Example:
> + emac0: qcom,emac@feb20000 {
> + cell-index = <0>;
> + compatible = "qcom,emac";
> + reg-names = "base", "csr", "ptp", "sgmii";
> + reg = <0xfeb20000 0x10000>,
> + <0xfeb36000 0x1000>,
> + <0xfeb3c000 0x4000>,
> + <0xfeb38000 0x400>;
> + #address-cells = <0>;
> + interrupt-parent = <&emac0>;
> + #interrupt-cells = <1>;
> + interrupts = <0 1>;
> + interrupt-map-mask = <0xffffffff>;
> + interrupt-map = <0 &intc 0 76 0
> + 1 &intc 0 80 0>;
> + interrupt-names = "emac_core0", "sgmii_irq";
> + qcom,emac-gpio-mdc = <&qcomgpio 123 0>;
> + qcom,emac-gpio-mdio = <&qcomgpio 124 0>;
> + qcom,emac-tstamp-en;
> + qcom,emac-ptp-frac-ns-adj = <125000000 1>;
> + phy-addr = <0>;
> + };
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
