Hi Arun, There happens to be a bug when auto generating event. It is fixed from master (2.26) all the way to 2.23.
Thank you for reporting. -- Abyot A. Gizaw. Senior Engineer, DHIS2 University of Oslo http://www.dhis2.org On Fri, Nov 18, 2016 at 9:07 AM, Abyot Asalefew Gizaw <[email protected]> wrote: > Is it possible to access your system so that I can take a close look? or > share your db privately? > > -- > Abyot A. Gizaw. > Senior Engineer, DHIS2 > University of Oslo > http://www.dhis2.org > > On Fri, Nov 18, 2016 at 5:58 AM, Arun Paul <[email protected]> wrote: > >> Hi Abyot, >> >> That's not the case. Anyway I cleaned the browser cache just to be double >> sure. >> The issue is still not solved. >> Any other ideas? >> >> Thanks >> , >> - Arun Paul >> >> On Wed, Nov 16, 2016 at 11:19 AM, Abyot Asalefew Gizaw <[email protected]> >> wrote: >> >>> May be the meta data is changed after the app has run... if this is the >>> case, the solution is to fully clear your browser cache and run the app >>> again. >>> >>> --- >>> >>> Thank you, >>> Abyot. >>> (sent from mobile) >>> >>> On Nov 16, 2016 03:39, "Arun Paul" <[email protected]> wrote: >>> >>>> Hi Abyot, >>>> >>>> This issue is still not resolved. I am attaching the screenshots here. >>>> I could not find anything error-like on the browser console too. I have >>>> attached the both the screenshots, just after enrolling to the program and >>>> just after manually generating the stage1 event. >>>> >>>> >>>> Let me know if you find anything. >>>> Thanks in advance. >>>> >>>> - Arun Paul >>>> >>>> On Mon, Nov 14, 2016 at 12:25 PM, Abyot Asalefew Gizaw <[email protected] >>>> > wrote: >>>> >>>>> Hi Arun, >>>>> >>>>> It works fine in our demo server - which is 2.25. I don't remember any >>>>> big change in that area between 2.23 and 2.25. >>>>> >>>>> Can you share us some screenshots? Also, do you see anything in red >>>>> under your browser console? >>>>> >>>>> -- >>>>> Abyot A. Gizaw. >>>>> Senior Engineer, DHIS2 >>>>> University of Oslo >>>>> http://www.dhis2.org >>>>> >>>>> On Mon, Nov 14, 2016 at 6:11 AM, Arun Paul <[email protected]> >>>>> wrote: >>>>> >>>>>> Thanks Prosper. >>>>>> Yes I set the incident date as the delivery date but it does not help. >>>>>> Is there anything else I have to check? >>>>>> >>>>>> Regards, >>>>>> Arun >>>>>> >>>>>> On Mon, Nov 14, 2016 at 1:09 AM, Prosper BT <[email protected]> >>>>>> wrote: >>>>>> >>>>>>> Dear Arun, >>>>>>> >>>>>>> Is delivery date your incident date? >>>>>>> You must have an incident date or use enrollment date for the auto >>>>>>> generate events to work. >>>>>>> >>>>>>> Regards >>>>>>> >>>>>>> Prosper Behumbiize, MPH >>>>>>> DHIS2 Implementation| HISP Uganda/University Of Oslo >>>>>>> +256 752 751 776 | +256 776 139 139 >>>>>>> [email protected] <[email protected]> | [email protected] | Skype: >>>>>>> prospertb >>>>>>> >>>>>>> On Sat, Nov 12, 2016 at 3:22 PM, Arun Paul <[email protected]> >>>>>>> wrote: >>>>>>> >>>>>>>> Hi everyone, >>>>>>>> >>>>>>>> I am creating a program for tracking the PNC visits in the lines of >>>>>>>> >>>>>>>> " >>>>>>>> MNCH / PNC (Adult Woman) >>>>>>>> " Program configured in the Sierra Leon Demo system. >>>>>>>> >>>>>>>> In my case I have created multiple PNC visits such as PNC 1, PNC2, >>>>>>>> PNC3 that would occur at 1,3,5 days after the delivery date which is >>>>>>>> the >>>>>>>> incident date of the program. >>>>>>>> >>>>>>>> I would like these events to be auto-generated at scheduled days, >>>>>>>> so that I can generate overdue reports for the health workers to act >>>>>>>> upon. >>>>>>>> However, I cannot get this working, despite doing all the >>>>>>>> configurations(Listed down below). Even after the required number of >>>>>>>> days, >>>>>>>> I can't see the overdue events are being generated for the patients, >>>>>>>> nor >>>>>>>> can I see them listed in the events overdue reports. >>>>>>>> >>>>>>>> In the program stage configuration for each stages : >>>>>>>> "Scheduled days from start" was given a valid value. >>>>>>>> "Auto-generate event" was ticked on. >>>>>>>> >>>>>>>> Have I missed any configuration? I am using version 2.23. >>>>>>>> >>>>>>>> Please help. >>>>>>>> >>>>>>>> Thanks, >>>>>>>> Arun Paul. >>>>>>>> >>>>>>>> _______________________________________________ >>>>>>>> Mailing list: https://launchpad.net/~dhis2-users >>>>>>>> Post to : [email protected] >>>>>>>> Unsubscribe : https://launchpad.net/~dhis2-users >>>>>>>> More help : https://help.launchpad.net/ListHelp >>>>>>>> >>>>>>>> >>>>>>> >>>>>> >>>>>> _______________________________________________ >>>>>> Mailing list: https://launchpad.net/~dhis2-users >>>>>> Post to : [email protected] >>>>>> Unsubscribe : https://launchpad.net/~dhis2-users >>>>>> More help : https://help.launchpad.net/ListHelp >>>>>> >>>>>> >>>>> >>>> >> >
_______________________________________________ Mailing list: https://launchpad.net/~dhis2-users Post to : [email protected] Unsubscribe : https://launchpad.net/~dhis2-users More help : https://help.launchpad.net/ListHelp
