I can run uhd_usrp_probe --args="addr=192.168.10.2" to get correct output now, but still get "No UHD Devices Found" error... linux; GNU C++ version 4.6.1; Boost_104601; UHD_003.004.000-307-gb61f4ad6
-- Opening a USRP2/N-Series device... -- Current recv frame size: 1472 bytes -- Current send frame size: 1472 bytes _____________________________________________________ / | Device: USRP2 / N-Series Device | _____________________________________________________ | / | | Mboard: USRP-N210-REV4 | | hardware: 2577 | | mac-addr: a0:36:fa:25:3b:98 | | ip-addr: 192.168.10.2 | | gpsdo: none | | serial: E9R1BR8UP | | | | Time sources: none, external, _external_, mimo | | Clock sources: internal, external, mimo | | Sensors: mimo_locked, ref_locked | | _____________________________________________________ | | / | | | RX DSP: 0 | | | Freq range: -50.000 to 50.000 Mhz | | _____________________________________________________ | | / | | | RX DSP: 1 | | | Freq range: -50.000 to 50.000 Mhz | | _____________________________________________________ | | / | | | RX Dboard: A | | | ID: RFX2400 (0x0027) | | | _____________________________________________________ | | | / | | | | RX Subdev: 0 | | | | Name: RFX RX | | | | Antennas: TX/RX, RX2, CAL | | | | Sensors: lo_locked, rssi | | | | Freq range: 2300.000 to 2900.000 Mhz | | | | Gain range PGA0: 0.0 to 70.0 step 0.0 dB | | | | Connection Type: QI | | | | Uses LO offset: No | | | _____________________________________________________ | | | / | | | | RX Codec: A | | | | Name: ads62p44 | | | | Gain range digital: 0.0 to 6.0 step 0.5 dB | | | | Gain range fine: 0.0 to 0.5 step 0.1 dB | | _____________________________________________________ | | / | | | TX DSP: 0 | | | Freq range: -250.000 to 250.000 Mhz | | _____________________________________________________ | | / | | | TX Dboard: A | | | ID: RFX2400 (0x002b) | | | _____________________________________________________ | | | / | | | | TX Subdev: 0 | | | | Name: RFX TX | | | | Antennas: TX/RX, CAL | | | | Sensors: lo_locked | | | | Freq range: 2300.000 to 2900.000 Mhz | | | | Gain Elements: None | | | | Connection Type: IQ | | | | Uses LO offset: Yes | | | _____________________________________________________ | | | / | | | | TX Codec: A | | | | Name: ad9777 | | | | Gain Elements: None On Mon, Mar 5, 2012 at 4:45 PM, Jiao Xianjun <[email protected]> wrote: > Seems that I find the problem: > > uhd_usrp_probe --args="addr=192.168.0.2" > > linux; GNU C++ version 4.6.1; Boost_104601; UHD_003.004.000-307-gb61f4ad6 > > Error: Network is unreachable > ryjiao@ryjiao-virtual-machine:~/Downloads/gnuradio/uhd/host/build/utils$ > uhd_usrp_probe --args="addr=192.168.10.2" > > linux; GNU C++ version 4.6.1; Boost_104601; UHD_003.004.000-307-gb61f4ad6 > > -- Opening a USRP2/N-Series device... > -- Current recv frame size: 1472 bytes > -- Current send frame size: 1472 bytes > Error: RuntimeError: > Please update the firmware and FPGA images for your device. > See the application notes for USRP2/N-Series for instructions. > Expected FPGA compatibility number 9, but got 8: > The FPGA build is not compatible with the host code build. > > > > On Mon, Mar 5, 2012 at 4:19 PM, Jiao Xianjun <[email protected]> wrote: > >> Hi, >> >> I just got a USRP N210 rev4.0, and install gnuradio+uhd with this script: >> http://www.sbrac.org/files/build-gnuradio in Ubuntu 11.10 (32bit). >> My eth config is: >> >> eth0 Link encap:Ethernet HWaddr 00:0c:29:2d:a9:f8 >> inet addr:192.168.10.1 Bcast:192.168.10.255 Mask:255.255.255.0 >> inet6 addr: fe80::20c:29ff:fe2d:a9f8/64 Scope:Link >> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 >> RX packets:2213 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:2997 errors:0 dropped:0 overruns:0 carrier:0 >> collisions:0 txqueuelen:1000 >> RX bytes:1829471 (1.8 MB) TX bytes:343606 (343.6 KB) >> Interrupt:19 Base address:0x2024 >> >> lo Link encap:Local Loopback >> inet addr:127.0.0.1 Mask:255.0.0.0 >> inet6 addr: ::1/128 Scope:Host >> UP LOOPBACK RUNNING MTU:16436 Metric:1 >> RX packets:1650 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:1650 errors:0 dropped:0 overruns:0 carrier:0 >> collisions:0 txqueuelen:0 >> RX bytes:123948 (123.9 KB) TX bytes:123948 (123.9 KB) >> >> and I do can ping 192.168.10.2: >> >> PING 192.168.10.2 (192.168.10.2) 56(84) bytes of data. >> 64 bytes from 192.168.10.2: icmp_req=1 ttl=32 time=2.05 ms >> 64 bytes from 192.168.10.2: icmp_req=2 ttl=32 time=1.75 ms >> 64 bytes from 192.168.10.2: icmp_req=3 ttl=32 time=1.93 ms >> 64 bytes from 192.168.10.2: icmp_req=4 ttl=32 time=1.80 ms >> 64 bytes from 192.168.10.2: icmp_req=5 ttl=32 time=2.04 ms >> 64 bytes from 192.168.10.2: icmp_req=6 ttl=32 time=1.94 ms >> 64 bytes from 192.168.10.2: icmp_req=7 ttl=32 time=2.01 ms >> 64 bytes from 192.168.10.2: icmp_req=8 ttl=32 time=1.78 ms >> ^C >> >> but when I run uhd_find_devices, the outputs are: >> >> linux; GNU C++ version 4.6.1; Boost_104601; UHD_003.004.000-307-gb61f4ad6 >> >> No UHD Devices Found >> >> Any one can help me, or give me some information? >> >> Thank you so much! >> >> BR >> >> putaoshu > > >
_______________________________________________ Discuss-gnuradio mailing list [email protected] https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
