Dear Sumit. I just noticed this thread: you're using RHEL 6, which only hast Boost 1.41; UHD cannot build with anything below Boost 1.46.
Is there a particular reason for sticking with this very old version, or can you upgrade to RHEL7 or CentOS7? Best regards, Marcus On 18.11.2015 23:43, Sumit Saluja wrote: > Please see the logs with -v option > > > ./build-gnuradio -v > This script will install Gnu Radio from current GIT sources > You will require Internet access from the computer on which this > script runs. You will also require SUDO access. You will require > approximately 500MB of free disk space to perform the build. > > This script will, as a side-effect, remove any existing Gnu Radio > installation that was installed from your Linux distribution packages. > It must do this to prevent problems due to interference between > a linux-distribution-installed Gnu Radio/UHD and one installed from > GIT source. > > > The whole process may take up to two hours to complete, depending on > the > capabilities of your > system. > > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! > NOTE: if you run into problems while running this script, you can > re-run it with > the --verbose option to produce lots of diagnostic output to help > debug problems. > This script has been written to anticipate some of the more common > problems one might > encounter building ANY large, complex software package. But it is not > pefect, and > there are certainly some situations it could encounter that it cannot > deal with > gracefully. Altering the system configuration from something > reasonably standard, > removing parts of the filesystem, moving system libraries around > arbitrarily, etc, > it likely cannot cope with. It is just a script. It isn't intuitive or > artificially > intelligent. It tries to make life a little easier for you, but at the > end of the day > if it runs into trouble, a certain amount of knowledge on your part > about > system configuration and idiosyncrasies will inevitably be > necessary. > > > Proceed?yes > Starting all functions at: Wed Nov 18 17:38:05 EST 2015 > SUDO privileges are required > Do you have SUDO privileges?yes > Continuing with script > ./build-gnuradio: line 1410: [: 90 > 90 > 90 > 90 > 90 > 90 > 90 > 90 > 90 > 90: integer expression expected > Installing prerequisites. > ====> THIS MAY TAKE QUITE SOME TIME <===== > Loaded plugins: refresh-packagekit, security > Setting up Remove Process > No Match for argument: gnuradio* > No Packages marked for removal > Loaded plugins: refresh-packagekit, security > Setting up Remove Process > No Match for argument: libgruel-* > No Packages marked for removal > Loaded plugins: refresh-packagekit, security > Setting up Remove Process > No Match for argument: libgruel* > No Packages marked for removal > Loaded plugins: refresh-packagekit, security > Setting up Group Process > Warning: Group Engineering and Scientific does not exist. > Package flex-2.5.35-9.el6.x86_64 already installed and latest version > Package gcc-4.4.7-16.el6.x86_64 already installed and latest version > Package redhat-rpm-config-9.0.3-44.sl6.noarch already installed and > latest version > Package rpm-build-4.8.0-47.el6.x86_64 already installed and latest > version > Package 1:make-3.81-20.el6.x86_64 already installed and latest > version > Package patch-2.6-6.el6.x86_64 already installed and latest > version > Package 1:pkgconfig-0.23-9.1.el6.x86_64 already installed and latest > version > Package gettext-0.17-18.el6.x86_64 already installed and latest > version > Package automake-1.11.1-4.el6.noarch already installed and latest > version > Package bison-2.4.1-5.el6.x86_64 already installed and latest > version > Package flex-devel-2.5.35-9.el6.x86_64 already installed and latest > version > Package libtool-2.2.6-15.5.el6.x86_64 already installed and latest > version > Package autoconf-2.63-5.1.el6.noarch already installed and latest > version > Package gcc-c++-4.4.7-16.el6.x86_64 already installed and latest > version > Package binutils-2.20.51.0.2-5.43.el6.x86_64 already installed and > latest version > Package patchutils-0.3.1-3.1.el6.x86_64 already installed and latest > version > Package byacc-1.9.20070509-7.el6.x86_64 already installed and latest > version > Package indent-2.2.10-7.el6.x86_64 already installed and latest > version > Package systemtap-2.7-2.el6.x86_64 already installed and latest > version > Package diffstat-1.51-2.el6.x86_64 already installed and latest > version > Package elfutils-0.161-3.el6.x86_64 already installed and latest > version > Package cvs-1.11.23-16.el6.x86_64 already installed and latest > version > Package rcs-5.7-37.el6.x86_64 already installed and latest > version > Package subversion-1.6.11-15.el6_7.x86_64 already installed and latest > version > Package gcc-gfortran-4.4.7-16.el6.x86_64 already installed and latest > version > Package 1:doxygen-1.6.1-6.el6.x86_64 already installed and latest > version > Package intltool-0.41.0-1.1.el6.noarch already installed and latest > version > Package git-1.8.3.1-1.sdl6.x86_64 already installed and latest > version > Package ctags-5.8-2.el6.x86_64 already installed and latest > version > Package cscope-15.6-6.el6.x86_64 already installed and latest > version > Package swig-1.3.40-6.el6.x86_64 already installed and latest > version > Warning: Group development does not have any > packages. > No packages in any requested group available to install or > update > Loaded plugins: refresh-packagekit, > security > Setting up Install > Process > Package fftw-devel-3.2.1-3.1.el6.x86_64 already installed and latest > version > Package cppunit-devel-1.12.1-3.1.el6.x86_64 already installed and > latest version > Package wxPython-devel-2.8.12.0-1.puias6.x86_64 already installed and > latest version > Package libusb-devel-0.1.12-23.el6.x86_64 already installed and latest > version > Package boost-devel-1.41.0-27.el6.x86_64 already installed and latest > version > Package alsa-lib-devel-1.0.22-3.el6.x86_64 already installed and > latest version > Package 1:numpy-1.6.2-0.1.puias6.x86_64 already installed and latest > version > Package gsl-devel-1.13-1.el6.x86_64 already installed and latest > version > Package python-devel-2.6.6-64.el6.x86_64 already installed and latest > version > No package pygsl > available. > Package python-cheetah-2.4.1-1.el6.x86_64 already installed and latest > version > Package python-mako-0.3.4-1.el6.noarch already installed and latest > version > Package python-lxml-2.2.3-1.1.el6.x86_64 already installed and latest > version > Package PyOpenGL-3.0.0-2.1.el6.noarch already installed and latest > version > Package 1:qt-devel-4.6.2-28.el6_5.x86_64 already installed and latest > version > Package 1:qt-4.6.2-28.el6_5.x86_64 already installed and latest > version > Package 1:qt-4.6.2-28.el6_5.x86_64 already installed and latest > version > Package 1:qt-devel-4.6.2-28.el6_5.x86_64 already installed and latest > version > Package PyQt4-devel-4.6.2-9.el6.x86_64 already installed and latest > version > Package qwt-devel-5.1.1-4.1.el6.x86_64 already installed and latest > version > Package qwtplot3d-qt4-devel-0.2.7-9.el6.x86_64 already installed and > latest version > Package libusb-0.1.12-23.el6.x86_64 already installed and latest > version > Package libusb-devel-0.1.12-23.el6.x86_64 already installed and latest > version > Package libusb1-1.0.9-0.6.rc1.el6.x86_64 already installed and latest > version > Package libusb1-devel-1.0.9-0.6.rc1.el6.x86_64 already installed and > latest version > Package cmake-2.8.12.2-4.el6.x86_64 already installed and latest > version > Package git-1.8.3.1-1.sdl6.x86_64 already installed and latest > version > Package wget-1.12-5.el6_6.1.x86_64 already installed and latest > version > Package python-docutils-0.6-1.el6.noarch already installed and latest > version > Package PyQwt-5.2.0-11.puias6.x86_64 already installed and latest > version > Package PyQwt-devel-5.2.0-11.puias6.x86_64 already installed and > latest version > Package qwt-devel-5.1.1-4.1.el6.x86_64 already installed and latest > version > Package gtk2-engines-2.18.4-5.el6.x86_64 already installed and latest > version > Package xmlrpc-c-client-1.16.24-1210.1840.el6.x86_64 already installed > and latest version > Package xmlrpc-c-c++-1.16.24-1210.1840.el6.x86_64 already installed > and latest version > Package xmlrpc-c-devel-1.16.24-1210.1840.el6.x86_64 already installed > and latest version > Package xmlrpc-c-apps-1.16.24-1210.1840.el6.x86_64 already installed > and latest version > Package xmlrpc-c-1.16.24-1210.1840.el6.x86_64 already installed and > latest version > Package xmlrpc-c-client++-1.16.24-1210.1840.el6.x86_64 already > installed and latest version > No package libzmq > available. > No package libzmq-dev > available. > Package tkinter-2.6.6-64.el6.x86_64 already installed and latest > version > Package orc-0.4.16-6.el6.x86_64 already installed and latest > version > Package python-requests-2.6.0-3.el6.noarch already installed and > latest version > Nothing to > do > > Checking for library libusb ...Found library > libusb > Checking for library libboost ...Found library > libboost > Checking for library libcppunit ...Found library > libcppunit > Checking for library libfftw ...Found library > libfftw > Checking for library libgsl ...Found library > libgsl > Done > > > This script will fetch Gnu Radio version 3.7/maint from the > repositories, along with compatible > extras. > > > Is this > OK?yes > > Fetching various packages (Gnu Radio, UHD, gr-osmosdr, gr-iqbal, > etc) > via the > Internet > > =======> THIS MAY TAKE QUITE SOME TIME > <========= > Fetching Gnu Radio via GIT...Cloning into > 'gnuradio'... > Submodule 'volk' (https://github.com/gnuradio/volk.git) registered for > path 'volk' > Cloning into > 'volk'... > > remote: Counting objects: 5589, done. > remote: Total 5589 (delta 0), reused 0 (delta 0), pack-reused 5589 > Receiving objects: 100% (5589/5589), 1.58 MiB | 266.00 KiB/s, done. > Resolving deltas: 100% (3997/3997), done. > Submodule path 'volk': checked out > 'f0b722392950bf7ede7b32f5ff60019bce7a8592' > M > volk > Branch maint set up to track remote branch maint from > origin. > Switched to a new branch > 'maint' > Done > > Fetching UHD via GIT...Cloning into > 'uhd'... > remote: Counting objects: 53257, done. > remote: Compressing objects: 100% (33/33), done. > remote: Total 53257 (delta 4), reused 0 (delta 0), pack-reused 53224 > Receiving objects: 100% (53257/53257), 96.50 MiB | 1.25 MiB/s, done. > Resolving deltas: 100% (40626/40626), done. > Fetching rtl-sdr (rtl-sdr, gr-osmosdr, gr-iqbal, hackrf, bladeRF and > airspy) via GIT > Cloning into > 'rtl-sdr'... > remote: Counting objects: 1617, done. > remote: Compressing objects: 100% (711/711), done. > remote: Total 1617 (delta 1182), reused 1213 (delta 898) > Receiving objects: 100% (1617/1617), 345.89 KiB | 529.00 KiB/s, done. > Resolving deltas: 100% (1182/1182), done. > Cloning into 'gr-osmosdr'... > remote: Counting objects: 3818, done. > remote: Compressing objects: 100% (2510/2510), done. > remote: Total 3818 (delta 2737), reused 1886 (delta 1270) > Receiving objects: 100% (3818/3818), 925.99 KiB | 876.00 KiB/s, done. > Resolving deltas: 100% (2737/2737), done. > Cloning into 'gr-iqbal'... > remote: Counting objects: 219, done. > remote: Compressing objects: 100% (175/175), done. > remote: Total 219 (delta 109), reused 98 (delta 40) > Receiving objects: 100% (219/219), 130.17 KiB | 0 bytes/s, done. > Resolving deltas: 100% (109/109), done. > Cloning into 'bladeRF'... > remote: Counting objects: 16325, done. > remote: Total 16325 (delta 0), reused 0 (delta 0), pack-reused 16325 > Receiving objects: 100% (16325/16325), 6.81 MiB | 1.37 MiB/s, done. > Resolving deltas: 100% (9380/9380), done. > Submodule 'libosmo-dsp' (git://git.osmocom.org/libosmo-dsp) registered > for path 'libosmo-dsp' > Cloning into > 'libosmo-dsp'... > > remote: Counting objects: 172, done. > remote: Compressing objects: 100% (106/106), done. > remote: Total 172 (delta 89), reused 123 (delta 58) > Receiving objects: 100% (172/172), 60.12 KiB | 0 bytes/s, done. > Resolving deltas: 100% (89/89), done. > Submodule path 'libosmo-dsp': checked out > 'f9df8894c72cbd491bdd2f6d4cbea95c46810267' > Cloning into > 'hackrf'... > remote: Counting objects: 9629, done. > remote: Total 9629 (delta 0), reused 0 (delta 0), pack-reused 9629 > Receiving objects: 100% (9629/9629), 24.49 MiB | 21.42 MiB/s, done. > Resolving deltas: 100% (6741/6741), done. > Cloning into 'host'... > remote: Counting objects: 626, done. > remote: Total 626 (delta 0), reused 0 (delta 0), pack-reused 626 > Receiving objects: 100% (626/626), 587.24 KiB | 0 bytes/s, done. > Resolving deltas: 100% (452/452), done. > Done > Starting function uhd_build at: Wed Nov 18 17:41:12 EST 2015 > Building UHD... > =============> THIS WILL TAKE SOME TIME <============= > > -- The CXX compiler identification is GNU 4.4.7 > -- The C compiler identification is GNU 4.4.7 > -- Check for working CXX compiler: /usr/bin/c++ > -- Check for working CXX compiler: /usr/bin/c++ -- works > -- Detecting CXX compiler ABI info > -- Detecting CXX compiler ABI info - done > -- Check for working C compiler: /usr/bin/cc > -- Check for working C compiler: /usr/bin/cc -- works > -- Detecting C compiler ABI info > -- Detecting C compiler ABI info - done > -- > -- Configuring the python interpreter... > -- Found PythonInterp: /usr/lib/python2.7/bin/python (found version > "2.7.8") > -- Python interpreter: /usr/lib/python2.7/bin/python > -- Override with: -DPYTHON_EXECUTABLE=<path-to-python> > -- Using UHD Images Directory: OFF > -- Build type not specified: defaulting to release. > -- Performing Test HAVE_VISIBILITY_HIDDEN > -- Performing Test HAVE_VISIBILITY_HIDDEN - Success > -- Performing Test HAVE_VISIBILITY_INLINES_HIDDEN > -- Performing Test HAVE_VISIBILITY_INLINES_HIDDEN - Success > -- > -- Configuring Boost C++ Libraries... > -- Could NOT find Boost > -- Boost include directories: /usr/include > -- Boost library directories: /usr/lib64 > -- Boost libraries: > -- Looking for log2 > -- Looking for log2 - found > -- > -- Python checking for Python version 2.6 or greater > -- Python checking for Python version 2.6 or greater - found > -- > -- Python checking for Mako templates 0.4 or greater > -- Python checking for Mako templates 0.4 or greater - found > -- > -- Configuring LibUHD support... > -- Dependency Boost_FOUND = 0 > -- Dependency HAVE_PYTHON_PLAT_MIN_VERSION = TRUE > -- Dependency HAVE_PYTHON_MODULE_MAKO = TRUE > CMake Error at cmake/Modules/UHDComponent.cmake:51 (MESSAGE): > Dependencies for required component LibUHD not met. > Call Stack (most recent call first): > CMakeLists.txt:279 (LIBUHD_REGISTER_COMPONENT) > > > -- Configuring incomplete, errors occurred! > See also "/home/ssaluja/test/uhd/host/build/CMakeFiles/CMakeOutput.log". > make: *** No rule to make target `clean'. Stop. > make: *** No targets specified and no makefile found. Stop. > UHD build apparently failed > Exiting UHD build > > ======================================================================= > If you have found this script useful and time-saving, consider a > donation to help me keep build-gnuradio, simple_ra, SIDsuite, > meteor_detector, simple_fm_rcv, and multimode maintained and up to date. > A simple paypal transfer to mle...@ripnet.com is all you need to do. > ====================================================================== > Send success/fail info to sbrac.org? > > ------------------------------------------------------------------------ > *From:* discuss-gnuradio-bounces+ssaluja=princeton....@gnu.org > [discuss-gnuradio-bounces+ssaluja=princeton....@gnu.org] on behalf of > Marcus D. Leech [mle...@ripnet.com] > *Sent:* Wednesday, November 18, 2015 3:58 PM > *To:* discuss-gnuradio@gnu.org > *Subject:* Re: [Discuss-gnuradio] Gnuradio-companion > > On 11/18/2015 03:45 PM, Sumit Saluja wrote: >> If I am building gnuradio manually Iam getting following message >> ###################################################### >> -- # Gnuradio disabled components >> -- ###################################################### >> -- * gr-ctrlport >> -- * gnuradio-companion >> -- * gr-comedi >> -- * gr-uhd >> -- * gr-video-sdl >> -- * gr-wxgui >> -- * gr-zeromq >> >> >> >> If I am building Gnuradio using build-gnuradio script then getting >> following error >> >> ====> THIS MAY TAKE QUITE SOME TIME <===== >> Checking for library libusb ...Found library libusb >> Checking for library libboost ...Found library libboost >> Checking for library libcppunit ...Found library libcppunit >> Checking for library libfftw ...Found library libfftw >> Checking for library libgsl ...Found library libgsl >> Done >> This script will fetch Gnu Radio version 3.7/maint from the >> repositories, along with compatible >> extras. >> Is this OK?yes >> Fetching various packages (Gnu Radio, UHD, gr-osmosdr, gr-iqbal, etc) >> via the Internet >> =======> THIS MAY TAKE QUITE SOME TIME <========= >> Fetching Gnu Radio via GIT...Done >> Fetching UHD via GIT...Fetching rtl-sdr (rtl-sdr, gr-osmosdr, >> gr-iqbal, hackrf, bladeRF and airspy) via GIT >> Done >> Starting function uhd_build at: Wed Nov 18 15:44:13 EST 2015 >> Building UHD... >> =============> THIS WILL TAKE SOME TIME <============= >> >> UHD build apparently failed >> Exiting UHD build >> >> >> >> >> Thanks >> Sumit Saluja >> > If you run build-gnuradio with -v, you'll get more logs, and likely a > note from Cmake that it couldn't find some depend that > gnuradio-companion relies on. > > >> >> >> ------------------------------------------------------------------------ >> *From:* 18740449846 [18740449...@163.com] >> *Sent:* Monday, November 16, 2015 7:56 PM >> *To:* Sumit Saluja >> *Subject:* »Ø¸´: [Discuss-gnuradio] Gnuradio-companion >> >> hi >> you need give some detail >> for example >> how do you build the gnuradio-companion and is you conmmand work well >> show us the result >> this is useful to solve you problem >> >> -----From Ekko >> >> >> -------- ÔʼÓʼþ -------- >> Ö÷Ì⣺[Discuss-gnuradio] Gnuradio-companion >> ·¢¼þÈË£ºSumit Saluja >> ÊÕ¼þÈË£ºdiscuss-gnuradio@gnu.org >> ³ËÍ£º >> >> >> Hi, >> >> I am building gnuradio on RHEL 6 and gnuradio-companion is not >> enabling . How I Should enable gnuradio-companion >> >> And UHD is not compiling on RHEL6. >> >> >> >> >> >> Thanks >> >> >> >> Sumit Saluja >> >> >> >> _______________________________________________ >> Discuss-gnuradio mailing list >> Discuss-gnuradio@gnu.org >> https://lists.gnu.org/mailman/listinfo/discuss-gnuradio > > > > _______________________________________________ > Discuss-gnuradio mailing list > Discuss-gnuradio@gnu.org > https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
_______________________________________________ Discuss-gnuradio mailing list Discuss-gnuradio@gnu.org https://lists.gnu.org/mailman/listinfo/discuss-gnuradio