The windows installer from that site seems to have been linked against
UHD 3.9.3, which is why the mismatch. There was no reason to have
separately installed UHD, since UHD is listed as a package that is
bundled into the installer.
I would remove the 3.9.4 UHD you have if you plan to use Gnu Radio
extensively, and the person who builds these windows releases will, at
some point, update the packaged UHD to 3.9.4 (or later).
On 2016-07-05 11:19, Sanat Kumar Mishra wrote:
> Hi,
>
> As suggested, I am putting the below mail in the discuss gnuradio list. I
> installed gnu radio from
> http://www.gcndevelopment.com/gnuradio/downloads.htm
> 64-Bit Any CPU - v3.7.9.2/v1.1.1.
>
> I first Installed GNU radio and then Installed the UHD. Will that might be a
> reason for the below mentioned problem??
>
> Best Regards,
> Sanat
>
> --------------------------------------------------------------------
> Not sure why you're getting the communication failtures, but your device
> appears, from the uhd_usrp_probe output to be functioning correctly.
>
> I suspect that your Gnu Radio installed was linked against UHD 3.9.3,
> which is why the apparent version mismatch, because clearly, your
> uhd_usrp_probe is linked against the newer library.
>
> How did you install Gnu Radio? This part of the discussion should
> probably be continued on the discuss-gnuradio mailing list.
>
> On 2016-07-05 10:58, Sanat Kumar Mishra wrote:
> I have got the following results: Please note I am using NI USRP 2943R
> which is like x310 from specification.
>
> Microsoft Windows [Version 6.1.7601]
> Copyright (c) 2009 Microsoft Corporation. Alle Rechte vorbehalten.
>
> C:\Users\smishra>uhd_usrp_probe --args resource=RIO0
> Win32; Microsoft Visual C++ version 14.0; Boost_105800;
> UHD_003.009.004-release
>
> UHD Error:
> x300 fw communication failure #1
> EnvironmentError: IOError: x300 fw poke32 - operation timed out
>
> UHD Error:
> x300 fw communication failure #1
> EnvironmentError: IOError: x300 fw poke32 - operation timed out
> -- X300 initialization sequence...
> -- Connecting to niusrpriorpc at localhost:5444...
> -- Using LVBITX bitfile C:\Program Files
> (x86)\UHD\share\uhd\images\usrp_x310_fp
> ga_HGS.lvbitx...
> -- Setup basic communication...
> -- Loading values from EEPROM...
> -- Setup RF frontend clocking...
> -- Radio 1x clock:200
> -- Detecting internal GPSDO.... No GPSDO found
> -- Initialize Radio0 control...
> -- Performing register loopback test... pass
> -- Initialize Radio1 control...
> -- Performing register loopback test... pass
> _____________________________________________________
> /
> | Device: X-Series Device
> | _____________________________________________________
> | /
> | | Mboard: X310
> | | revision: 8
> | | revision_compat: 7
> | | product: 30813
> | | mac-addr0: 00:80:2f:25:18:f9
> | | mac-addr1: 00:80:2f:25:18:fa
> | | gateway: 192.168.10.1
> | | ip-addr0: 192.168.10.2
> | | subnet0: 255.255.255.0
> | | ip-addr1: 192.168.20.2
> | | subnet1: 255.255.255.0
> | | ip-addr2: 192.168.30.2
> | | subnet2: 255.255.255.0
> | | ip-addr3: 192.168.40.2
> | | subnet3: 255.255.255.0
> | | serial: 30D44AD
> | | FW Version: 4.0
> | | FPGA Version: 19.0
> | |
> | | Time sources: internal, external, gpsdo
> | | Clock sources: internal, external, gpsdo
> | | Sensors: ref_locked
> | | _____________________________________________________
> | | /
> | | | RX DSP: 0
> | | | Freq range: -100.000 to 100.000 MHz
> | | _____________________________________________________
> | | /
> | | | RX DSP: 1
> | | | Freq range: -100.000 to 100.000 MHz
> | | _____________________________________________________
> | | /
> | | | RX Dboard: A
> | | | ID: CBX-120 (0x0085)
> | | | Serial: 30D2211
> | | | _____________________________________________________
> | | | /
> | | | | RX Frontend: 0
> | | | | Name: CBX-120 RX
> | | | | Antennas: TX/RX, RX2, CAL
> | | | | Sensors: lo_locked
> | | | | Freq range: 1200.000 to 6000.000 MHz
> | | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB
> | | | | Bandwidth range: 120000000.0 to 120000000.0 step 0.0 Hz
> | | | | Connection Type: IQ
> | | | | Uses LO offset: No
> | | | _____________________________________________________
> | | | /
> | | | | RX Codec: A
> | | | | Name: ads62p48
> | | | | Gain range digital: 0.0 to 6.0 step 0.5 dB
> | | _____________________________________________________
> | | /
> | | | RX Dboard: B
> | | | ID: CBX-120 (0x0085)
> | | | Serial: 30D2216
> | | | _____________________________________________________
> | | | /
> | | | | RX Frontend: 0
> | | | | Name: CBX-120 RX
> | | | | Antennas: TX/RX, RX2, CAL
> | | | | Sensors: lo_locked
> | | | | Freq range: 1200.000 to 6000.000 MHz
> | | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB
> | | | | Bandwidth range: 120000000.0 to 120000000.0 step 0.0 Hz
> | | | | Connection Type: IQ
> | | | | Uses LO offset: No
> | | | _____________________________________________________
> | | | /
> | | | | RX Codec: B
> | | | | Name: ads62p48
> | | | | Gain range digital: 0.0 to 6.0 step 0.5 dB
> | | _____________________________________________________
> | | /
> | | | TX DSP: 0
> | | | Freq range: -100.000 to 100.000 MHz
> | | _____________________________________________________
> | | /
> | | | TX DSP: 1
> | | | Freq range: -100.000 to 100.000 MHz
> | | _____________________________________________________
> | | /
> | | | TX Dboard: A
> | | | ID: CBX-120 (0x0084)
> | | | Serial: 30D2211
> | | | _____________________________________________________
> | | | /
> | | | | TX Frontend: 0
> | | | | Name: CBX-120 TX
> | | | | Antennas: TX/RX, CAL
> | | | | Sensors: lo_locked
> | | | | Freq range: 1200.000 to 6000.000 MHz
> | | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB
> | | | | Bandwidth range: 120000000.0 to 120000000.0 step 0.0 Hz
> | | | | Connection Type: QI
> | | | | Uses LO offset: No
> | | | _____________________________________________________
> | | | /
> | | | | TX Codec: A
> | | | | Name: ad9146
> | | | | Gain Elements: None
> | | _____________________________________________________
> | | /
> | | | TX Dboard: B
> | | | ID: CBX-120 (0x0084)
> | | | Serial: 30D2216
> | | | _____________________________________________________
> | | | /
> | | | | TX Frontend: 0
> | | | | Name: CBX-120 TX
> | | | | Antennas: TX/RX, CAL
> | | | | Sensors: lo_locked
> | | | | Freq range: 1200.000 to 6000.000 MHz
> | | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB
> | | | | Bandwidth range: 120000000.0 to 120000000.0 step 0.0 Hz
> | | | | Connection Type: QI
> | | | | Uses LO offset: No
> | | | _____________________________________________________
> | | | /
> | | | | TX Codec: B
> | | | | Name: ad9146
> | | | | Gain Elements: None
>
> Quoting mle...@ripnet.com:
>
> open up a command window
>
> On 2016-07-05 10:44, Sanat Kumar Mishra wrote:
>
> Hi,
>
> I am using Windows 7. Where shall I write this command?
>
> Zitat von mle...@ripnet.com:
>
> What happens if you:
>
> uhd_usrp_probe --args resource=RIO0
>
> ??
>
> On 2016-07-05 10:37, Sanat Kumar Mishra wrote:
>
> Hi,
>
> @"The communications error is of more concern. What type of Ethernet
> card do you have on your system? What is your network setup between your
> computer and the X300?"
> --- I am using NI USRP 2943-R which I found in the einternet as X310.
> Therefore I flashed usrp_x310_fpga_HGS.lvbitx image to the device. I am
> using PCI Express for communication using MXI Express cable as a result I
> havenot set any network setup for the same.
> Please guide me what to do.
>
> Regards,
> Sanat
>
> Zitat von mle...@ripnet.com:
>
> The fact that the header indicates 003.009.003 means that you're
> actually running 003.009.003, if you installed 3.9.4, it's likely in a
> place outside your %PATH%.
>
> The 'can't open file' error is coming from Gnu Radio, not UHD. My
> suspicion is that it's trying to open a file that it cannot open on
> Windows, or is specified wrongly. Not all of the examples are 100%
> portable.
>
> The communications error is of more concern. What type of Ethernet card
> do you have on your system? What is your network setup between your
> computer and the X300?
>
> On 2016-07-05 06:48, Sanat Kumar Mishra wrote:
>
> Hello,
>
> I am trying to run the FM receiver example (from youtube) and I get the
> following errors:
>
> "Win32; Microsoft Visual C++ version 14.0; Boost_106000;
> UHD_003.009.003-0-unknown" - But I am using UHD_003.009.004.
>
> "No such file or directory
> Traceback (most recent call last):
> File "C:\Users\smishra\Downloads\fm_example.py", line 162, in <module>
> main()
> File "C:\Users\smishra\Downloads\fm_example.py", line 156, in main
> tb = top_block_cls()
> File "C:\Users\smishra\Downloads\fm_example.py", line 117, in __init__
> self.blocks_wavfile_sink_0 = blocks.wavfile_sink("", 1, 96000, 8)
> File "C:\Program
> Files\GNURadio-3.7\lib\site-packages\gnuradio\blocks\blocks_swig1.py",
> line 2701, in make
> return _blocks_swig1.wavfile_sink_make(filename, n_channels,
> sample_rate, bits_per_sample)
> RuntimeError: can't open file"
>
> "UHD Error:
> x300 fw communication failure #1
> EnvironmentError: IOError: x300 fw poke32 - operation timed out."
>
> The PPS LED is blinking which as per the 'Getting Started Guide' means
> 'The device is not locked to the reference signal.'
>
> Regards,
> Sanat
>
> Quoting mle...@ripnet.com:
>
> Could you perhaps share with us the exact error message you received?
>
> On 2016-07-04 09:50, Sanat Kumar Mishra via USRP-users wrote:
>
> Hi,
>
> I just received the NI USRP-2943R device. It has built-in LabView FW
> and FPGA images. In NI forum, I read that in order to establish
> communication between the USRP and GNUradio, the latest UHD FW and FPGA
> images needs to be flashed into the USRP. I downloaded the latest UHD
> which is USRP Hardware Driver 003.009.004. Using NI USRP configuration
> Utility tool I was able to flash the UHD FPGA image
> usrp_x310_fpga_HGS.lvbitx into the USRP. Iam using windows 7 - 64 bit
> for my GNUradio application.
>
> After doing this, the GNUradio application gives FW error.
>
> My question is what is the right verion of FW that is compatibale with
> the NI-USRP 2943R and which tool to use to load it ?
>
> Best Regards,
> Sanat
>
> _______________________________________________
> USRP-users mailing list
> usrp-us...@lists.ettus.com
> http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com_______________________________________________
Discuss-gnuradio mailing list
Discuss-gnuradio@gnu.org
https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
