Just a few changes below:
On 1/6/22 08:37, Thore Sommer wrote:
> The grammar for the events dm_device_remove, device_resume and
> dm_table_clear did not include the no_data entry when device data
> and hash are missing.
>
> For the device uuid or name "=" is also escaped with a "\".
>
> Add a note that dm_table_load might split its target measurements over
> multiple IMA events.
>
> Signed-off-by: Thore Sommer <pub...@thson.de>
> ---
> .../admin-guide/device-mapper/dm-ima.rst | 26 ++++++++++++++-----
> 1 file changed, 20 insertions(+), 6 deletions(-)
>
> diff --git a/Documentation/admin-guide/device-mapper/dm-ima.rst
> b/Documentation/admin-guide/device-mapper/dm-ima.rst
> index a4aa50a828e0..fb6e4148b426 100644
> --- a/Documentation/admin-guide/device-mapper/dm-ima.rst
> +++ b/Documentation/admin-guide/device-mapper/dm-ima.rst
> @@ -100,6 +100,9 @@ When a new table is loaded in a device's inactive table
> slot,
> the device information and target specific details from the
> targets in the table are measured.
>
> +Note that if there are too many targets to measure at once multiple IMA
> +measurements will be generated.
> +
> The IMA measurement log has the following format for 'dm_table_load':
>
> ::
> @@ -118,9 +121,9 @@ The IMA measurement log has the following format for
> 'dm_table_load':
> device_minor := "minor=" <N>
> minor_count := "minor_count=" <N>
> num_device_targets := "num_targets=" <N>
> - dm-device-name := Name of the device. If it contains special characters
> like '\', ',', ';',
> + dm-device-name := Name of the device. If it contains special characters
> like '\', ',', ';',"=",
';', '=',
> they are prefixed with '\'.
> - dm-device-uuid := UUID of the device. If it contains special characters
> like '\', ',', ';',
> + dm-device-uuid := UUID of the device. If it contains special characters
> like '\', ',', ';',"=",
';', '=',
> they are prefixed with '\'.
>
> table_load_data := <target_data>
> @@ -175,8 +178,9 @@ The IMA measurement log has the following format for
> 'dm_device_resume':
> ::
>
> EVENT_NAME := "dm_device_resume"
> - EVENT_DATA := <dm_version_str> ";" <device_metadata> ";"
> <active_table_hash> ";" <current_device_capacity> ";"
> + EVENT_DATA := <dm_version_str> ";" device_data ";"
> <current_device_capacity> ";"
>
> + device_data := <device_metadata> ";" <active_table_hash> |
> device_resume_no_data
> dm_version_str := As described in the 'Table load' section above.
> device_metadata := As described in the 'Table load' section above.
> active_table_hash := "active_table_hash=" <table_hash_alg> ":" <table_hash>
> @@ -189,6 +193,9 @@ The IMA measurement log has the following format for
> 'dm_device_resume':
> events for a given device, the hash is computed combining all
> the event data
> i.e. (<dm_version_str> ";" <device_metadata> ";"
> <table_load_data> ";")
> across all those events.
> + device_resume_no_data := "device_resume=no_data"
> + If device metadata and hash for the active table
> do not exists this value gets measured.
do not exist, this value is measured.
> + Note: the hash should always exist if the device
> metadata is present.
> current_device_capacity := "current_device_capacity=" <N>
>
> For instance, if a linear device is resumed with the following command,
> @@ -213,10 +220,10 @@ The IMA measurement log has the following format for
> 'dm_device_remove':
> ::
>
> EVENT_NAME := "dm_device_remove"
> - EVENT_DATA := <dm_version_str> ";" <device_active_metadata> ";"
> <device_inactive_metadata> ";"
> - <active_table_hash> "," <inactive_table_hash> ","
> <remove_all> ";" <current_device_capacity> ";"
> + EVENT_DATA := <dm_version_str> ";" <device_data> <remove_all> ";"
> <current_device_capacity> ";"
>
> dm_version_str := As described in the 'Table load' section above.
> + device_data := <device_active_metadata> ";" <device_inactive_metadata> ";"
> <active_table_hash> "," <inactive_table_hash> "," | <device_remove_no_data>
> ";"
> device_active_metadata := Device metadata that reflects the currently
> loaded active table.
> The format is same as 'device_metadata' described
> in the 'Table load' section above.
> device_inactive_metadata := Device metadata that reflects the inactive
> table.
> @@ -225,6 +232,9 @@ The IMA measurement log has the following format for
> 'dm_device_remove':
> The format is same as 'active_table_hash' described in
> the 'Device resume' section above.
> inactive_table_hash := Hash of the inactive table.
> The format is same as 'active_table_hash' described
> in the 'Device resume' section above.
> + device_remove_no_data := "device_remove=no_data"
> + If device metadata and hash for the active and
> inactive table do not exists this value gets measured.
exist, this value is measured.
> + Note: the hash should always exist if the device
> metadata is present.
> remove_all := "remove_all=" <yes_no>
> yes_no := "y" | "n"
> current_device_capacity := "current_device_capacity=" <N>
> @@ -254,9 +264,13 @@ The IMA measurement log has the following format for
> 'dm_table_clear':
> ::
>
> EVENT_NAME := "dm_table_clear"
> - EVENT_DATA := <dm_version_str> ";" <device_inactive_metadata> ";"
> <inactive_table_hash> ";" <current_device_capacity> ";"
> + EVENT_DATA := <dm_version_str> ";" <device_data> ";"
> <current_device_capacity> ";"
>
> dm_version_str := As described in the 'Table load' section above.
> + device_data := <device_inactive_metadata> ";" <inactive_table_hash> |
> <table_clear_no_data>
> + table_clear_no_data := "table_clear=no_data"
> + If device metadata and hash for the inactive table
> do not exists this value gets measured.
exist, this value is measured.
> + Note: the hash should always exist if the device
> metadata is present.
> device_inactive_metadata := Device metadata that was captured during the
> load time inactive table being cleared.
> The format is same as 'device_metadata'
> described in the 'Table load' section above.
> inactive_table_hash := Hash of the inactive table being cleared from the
> device.
thanks.
--
~Randy
--
dm-devel mailing list
dm-devel@redhat.com
https://listman.redhat.com/mailman/listinfo/dm-devel
