Hi Meji
In three weeks i will have two Intel NIC X520-QDA1 of 40 Gb/s, according to
these link:
http://ark.intel.com/products/68672/Intel-Ethernet-Converged-Network-Adapter-X520-QDA1
http://www.intel.com/content/www/us/en/network-adapters/converged-network-adapters/ethernet-x520-qda1-brief.html
In my Hardware setup also i have a RAID controller H710p of Dell (LSI
chipset with 1 MB of cache) and with two groups of 4 HDDs SAS 15K RPM, each
group is configured in RAID 10, this setup is applied for each Server (the
HDDs for the OS are in other RAID), obviously i don't have much storage
compared to yours.
In these Servers i will have running DRBD 8.4.5 version
If you want to know the result of my tests, only let me know.
Best regards
Cesar
----- Original Message -----
From: "Meij, Henk" <hm...@wesleyan.edu>
To: <drbd-user@lists.linbit.com>
Sent: Thursday, October 23, 2014 5:10 PM
Subject: Re: [DRBD-user] drbd storage size
a) it turns out the counter (8847740/11287100)M goes down, not up, deh,
never noticed
b) ran plain rsync across eth0 (public, with switches/routers) and eth1
(nic to nic)
eth0 sent 585260755954 bytes received 10367 bytes 116690412.98 bytes/sec
eth1 sent 585260755954 bytes received 10367 bytes 122580535.41 bytes/sec
so my LSI raid card is behaving and DRBD is slowing the initialization
down somehow.
Found chapter 15 and will try some suggestions but ideas welcome.
c) for grins
version: 8.4.5 (api:1/proto:86-101)
GIT-hash: 1d360bde0e095d495786eaeb2a1ac76888e4db96 build by
mockbuild@Build64R6, 2014-08-17 19:26:04
0: cs:SyncTarget ro:Secondary/Secondary ds:Inconsistent/UpToDate C r-----
ns:0 nr:3601728 dw:3601408 dr:0 al:0 bm:0 lo:4 pe:11 ua:3 ap:0 ep:1
wo:f oos:109374215324
[>....................] sync'ed: 0.1% (106810756/106814272)M
finish: 731:23:05 speed: 41,532 (31,868) want: 41,000 K/sec
100TB in 731 hours would be 30 days. Can I expect large delta data
replication to go equally slow using DRDB?
-Henk
________________________________________
From: drbd-user-boun...@lists.linbit.com
[drbd-user-boun...@lists.linbit.com] on behalf of Meij, Henk
[hm...@wesleyan.edu]
Sent: Thursday, October 23, 2014 9:57 AM
To: Philipp Reisner; drbd-user@lists.linbit.com
Subject: Re: [DRBD-user] drbd storage size
Thanks for the write up y'll. I'll have to think about #3 not sure I
grasp it fully.
Last night I started a 12 TB test and started first initialization for
observation (0 is primary).
I have node0:eth1 wired directly into node1:eth1 with 10 foot CAT 6 cable
(MTU=9000)
Data from node1 to node0
PING 10.10.52.232 (10.10.52.232) 8970(8998) bytes of data.
8978 bytes from 10.10.52.232: icmp_seq=1 ttl=64 time=0.316 ms
This morning's progress report from node1:(drbd v8.4.5)
[===>................] sync'ed: 21.7% (8847740/11287100)M
finish: 62:50:50 speed: 40,032 (39,008) want: 68,840 K/sec
which confuses me: 8.8M out of 11.3M is 77.8% synced, not? I will let this
test finish before I do a dd attempt.
iostat reveals %idle cpu 99%+ and little to no %iowait (near 0%), iotop
confirms very little IO (<5 K/s), typical data
Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s avgrq-sz
avgqu-sz await svctm %util
sdb1 0.00 231.00 0.00 156.33 0.00 79194.67 506.58
0.46 2.94 1.49 23.37
Something is throttling this IO as 40M/s is about half of what I was
hoping for. Will dig some more.
-Henk
________________________________________
From: drbd-user-boun...@lists.linbit.com
[drbd-user-boun...@lists.linbit.com] on behalf of Philipp Reisner
[philipp.reis...@linbit.com]
Sent: Thursday, October 23, 2014 9:17 AM
To: drbd-user@lists.linbit.com
Subject: Re: [DRBD-user] drbd storage size
Am Donnerstag, 23. Oktober 2014, 08:55:03 schrieb Digimer:
On 23/10/14 04:00 AM, Philipp Reisner wrote:
> 2a) Initialize both backend devices to a known state.
>
> I.e. dd if=/dev/zero of=/dev/sdb1 bs=$((1024*1024)) oflag=direct
Question;
What I've done in the past to speed up initial sync is to create the
DRBD device, pause-sync, then do your 'dd if=/dev/zero ...' trick to
/dev/drbd0. This effectively drives the resync speed to the max possible
and ensures full sync across both nodes. Is this a sane approach?
Yes, sure that is a way to do it. (I have the impression that is something
form the drbd-8.3 world.)
I do not know from the top of the head if that will be faster than the
built-in background resync in drbd-8.4.
Best,
Phil
_______________________________________________
drbd-user mailing list
drbd-user@lists.linbit.com
http://lists.linbit.com/mailman/listinfo/drbd-user
_______________________________________________
drbd-user mailing list
drbd-user@lists.linbit.com
http://lists.linbit.com/mailman/listinfo/drbd-user
_______________________________________________
drbd-user mailing list
drbd-user@lists.linbit.com
http://lists.linbit.com/mailman/listinfo/drbd-user
_______________________________________________
drbd-user mailing list
drbd-user@lists.linbit.com
http://lists.linbit.com/mailman/listinfo/drbd-user
