Hi Pier,

What is the chipset of your bge device? You could provide these
information with this command:
  prtconf -vp | grep 14e4,


Regards,
Crisson
On Tue, 2008-10-21 at 09:10 +0200, Pierguido wrote:
> hi all.
> I have to say i'm pretty new to opensolaris and solaris in general, but 
> till now i didn't have so many problems.
> I'm trying to install sxce snv_99 on a HP ML 150 G3 with a dual ethernet 
> PCI-E and a lsi scsi hba card (both are HP).
> Withg scsi no problem, but i'm going crazy trying to use the broadcom 
> nic that is on the motherboard.
> In dmesg i got this:
> 
> Oct 20 18:33:53 srv-storage unix: [ID 954099 kern.info] NOTICE: IRQ18 is 
> being shared by drivers with different interrupt levels.
> Oct 20 18:33:53 srv-storage This may result in reduced system performance.
> 
> These ar the irqs:
> 
> IRQ  Vect IPL Bus    Trg Type   CPU Share APIC/INT# Driver Name(s)
> 4    0xb0 12  ISA    Edg Fixed  1   1     0x0/0x4   asy#0
> 9    0x81 9   PCI    Lvl Fixed  1   1     0x0/0x9   acpi_wrapper_isr
> 14   0x42 5   ISA    Edg Fixed  1   1     0x0/0xe   ata#0
> 16   0x40 5   PCIe   Lvl Fixed  0   3     0x0/0x10  uhci#3, cpqary3#0, 
> pcie_pci#
> 2
> 18   0x61 6   PCI    Lvl Fixed  0   2     0x0/0x12  bge#0, uhci#2
> 20   0x21 1   PCI    Lvl Fixed  0   1     0x0/0x14  uhci#1
> 23   0x20 1   PCI    Lvl Fixed  1   2     0x0/0x17  uhci#0, ehci#0
> 48   0x60 6   PCIe   Edg MSI    1   1     -         e1000g#0
> 49   0x41 5   PCI    Edg MSI    0   1     -         mpt#1
> 50   0x62 6   PCIe   Edg MSI    1   1     -         e1000g#1
> 160  0xa0 0          Edg IPI    all 0     -         poke_cpu
> 192  0xc0 13         Edg IPI    all 1     -         xc_serv
> 208  0xd0 14         Edg IPI    all 1     -         kcpc_hw_overflow_intr
> 209  0xd1 14         Edg IPI    all 1     -         cbe_fire
> 210  0xd3 14         Edg IPI    all 1     -         cbe_fire
> 240  0xe0 15         Edg IPI    all 1     -         xc_serv
> 241  0xe1 15         Edg IPI    all 1     -         apic_error_intr
> 
> the nics:
> 
> [EMAIL PROTECTED]:~$ dladm show-phys
> LINK         MEDIA                STATE      SPEED DUPLEX   DEVICE
> e1000g0      Ethernet             up         1000 full      e1000g0
> e1000g1      Ethernet             unknown    0    half      e1000g1
> 
> If i try to force the nic:
> 
> [EMAIL PROTECTED]:~$ ifconfig bge0 plumb
> ifconfig: cannot open link "bge0": No such device or address
> 
> I don't know what to do anymore...do you have some suggestions?
> Thanks
> 
> Pier
> _______________________________________________
> driver-discuss mailing list
> [email protected]
> http://mail.opensolaris.org/mailman/listinfo/driver-discuss
-- 
*************************************
* Guang-Hao, Crisson Hu             *
* China ERI, Sun Microsystems, Inc. *
* Tel: +86-10-62673095              *
*************************************


_______________________________________________
driver-discuss mailing list
[email protected]
http://mail.opensolaris.org/mailman/listinfo/driver-discuss

Reply via email to