On 09/23/13 15:36, Juergen Beisert wrote:
> Signed-off-by: Juergen Beisert <j...@pengutronix.de>
> CC: linux-arm-ker...@lists.infradead.org
> CC: linux-in...@vger.kernel.org
> CC: de...@driverdev.osuosl.org
> CC: Marek Vasut <ma...@denx.de>
> CC: Fabio Estevam <fabio.este...@freescale.com>
> CC: Jonathan Cameron <ji...@cam.ac.uk>
Applied to the togreg branch of iio.git
Thanks,
> ---
> drivers/staging/iio/adc/mxs-lradc.c | 163
> ------------------------------------
> 1 file changed, 163 deletions(-)
>
> diff --git a/drivers/staging/iio/adc/mxs-lradc.c
> b/drivers/staging/iio/adc/mxs-lradc.c
> index 76a900d..aa1f337 100644
> --- a/drivers/staging/iio/adc/mxs-lradc.c
> +++ b/drivers/staging/iio/adc/mxs-lradc.c
> @@ -186,7 +186,6 @@ struct mxs_lradc {
> bool use_touchbutton;
>
> struct input_dev *ts_input;
> - struct work_struct ts_work;
>
> enum mxs_lradc_id soc;
> enum lradc_ts_plate cur_plate; /* statemachine */
> @@ -830,168 +829,6 @@ static const struct iio_info mxs_lradc_iio_info = {
> .read_raw = mxs_lradc_read_raw,
> };
>
> -static int mxs_lradc_ts_touched(struct mxs_lradc *lradc)
> -{
> - uint32_t reg;
> -
> - /* Enable touch detection. */
> - mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
> - mxs_lradc_reg_set(lradc, mxs_lradc_touch_detect_bit(lradc),
> - LRADC_CTRL0);
> -
> - msleep(LRADC_TS_SAMPLE_DELAY_MS);
> -
> - reg = readl(lradc->base + LRADC_STATUS);
> -
> - return reg & LRADC_STATUS_TOUCH_DETECT_RAW;
> -}
> -
> -static int32_t mxs_lradc_ts_sample(struct mxs_lradc *lradc,
> - enum lradc_ts_plate plate, int change)
> -{
> - unsigned long delay, jiff;
> - uint32_t reg, ctrl0 = 0, chan = 0;
> - /* The touchscreen always uses CTRL4 slot #7. */
> - const uint8_t slot = 7;
> - uint32_t val;
> -
> - /*
> - * There are three correct configurations of the controller sampling
> - * the touchscreen, each of these configuration provides different
> - * information from the touchscreen.
> - *
> - * The following table describes the sampling configurations:
> - * +-------------+-------+-------+-------+
> - * | Wire \ Axis | X | Y | Z |
> - * +---------------------+-------+-------+
> - * | X+ (CH2) | HI | TS | TS |
> - * +-------------+-------+-------+-------+
> - * | X- (CH4) | LO | SH | HI |
> - * +-------------+-------+-------+-------+
> - * | Y+ (CH3) | SH | HI | HI |
> - * +-------------+-------+-------+-------+
> - * | Y- (CH5) | TS | LO | SH |
> - * +-------------+-------+-------+-------+
> - *
> - * HI ... strong '1' ; LO ... strong '0'
> - * SH ... sample here ; TS ... tri-state
> - *
> - * There are a few other ways of obtaining the Z coordinate
> - * (aka. pressure), but the one in the table seems to be the
> - * most reliable one.
> - */
> - switch (plate) {
> - case LRADC_SAMPLE_X:
> - ctrl0 = mxs_lradc_drive_x_plate(lradc);
> - chan = 3;
> - break;
> - case LRADC_SAMPLE_Y:
> - ctrl0 = mxs_lradc_drive_y_plate(lradc);
> - chan = 4;
> - break;
> - case LRADC_SAMPLE_PRESSURE:
> - ctrl0 = mxs_lradc_drive_pressure(lradc);
> - chan = 5;
> - break;
> - }
> -
> - if (change) {
> - mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc),
> - LRADC_CTRL0);
> - mxs_lradc_reg_set(lradc, ctrl0, LRADC_CTRL0);
> -
> - mxs_lradc_reg_clear(lradc, LRADC_CTRL4_LRADCSELECT_MASK(slot),
> - LRADC_CTRL4);
> - mxs_lradc_reg_set(lradc,
> - chan << LRADC_CTRL4_LRADCSELECT_OFFSET(slot),
> - LRADC_CTRL4);
> - }
> -
> - mxs_lradc_reg_clear(lradc, 0xffffffff, LRADC_CH(slot));
> - mxs_lradc_reg_set(lradc, 1 << slot, LRADC_CTRL0);
> -
> - delay = jiffies + msecs_to_jiffies(LRADC_TS_SAMPLE_DELAY_MS);
> - do {
> - jiff = jiffies;
> - reg = readl_relaxed(lradc->base + LRADC_CTRL1);
> - if (reg & LRADC_CTRL1_LRADC_IRQ(slot))
> - break;
> - } while (time_before(jiff, delay));
> -
> - mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ(slot), LRADC_CTRL1);
> -
> - if (time_after_eq(jiff, delay))
> - return -ETIMEDOUT;
> -
> - val = readl(lradc->base + LRADC_CH(slot));
> - val &= LRADC_CH_VALUE_MASK;
> -
> - return val;
> -}
> -
> -static int32_t mxs_lradc_ts_sample_filter(struct mxs_lradc *lradc,
> - enum lradc_ts_plate plate)
> -{
> - int32_t val, tot = 0;
> - int i;
> -
> - val = mxs_lradc_ts_sample(lradc, plate, 1);
> -
> - /* Delay a bit so the touchscreen is stable. */
> - mdelay(2);
> -
> - for (i = 0; i < LRADC_TS_SAMPLE_AMOUNT; i++) {
> - val = mxs_lradc_ts_sample(lradc, plate, 0);
> - tot += val;
> - }
> -
> - return tot / LRADC_TS_SAMPLE_AMOUNT;
> -}
> -
> -static void mxs_lradc_ts_work(struct work_struct *ts_work)
> -{
> - struct mxs_lradc *lradc = container_of(ts_work,
> - struct mxs_lradc, ts_work);
> - int val_x, val_y, val_p;
> - bool valid = false;
> -
> - while (mxs_lradc_ts_touched(lradc)) {
> - /* Disable touch detector so we can sample the touchscreen. */
> - mxs_lradc_reg_clear(lradc, mxs_lradc_touch_detect_bit(lradc),
> - LRADC_CTRL0);
> -
> - if (likely(valid)) {
> - input_report_abs(lradc->ts_input, ABS_X, val_x);
> - input_report_abs(lradc->ts_input, ABS_Y, val_y);
> - input_report_abs(lradc->ts_input, ABS_PRESSURE, val_p);
> - input_report_key(lradc->ts_input, BTN_TOUCH, 1);
> - input_sync(lradc->ts_input);
> - }
> -
> - valid = false;
> -
> - val_x = mxs_lradc_ts_sample_filter(lradc, LRADC_SAMPLE_X);
> - if (val_x < 0)
> - continue;
> - val_y = mxs_lradc_ts_sample_filter(lradc, LRADC_SAMPLE_Y);
> - if (val_y < 0)
> - continue;
> - val_p = mxs_lradc_ts_sample_filter(lradc,
> LRADC_SAMPLE_PRESSURE);
> - if (val_p < 0)
> - continue;
> -
> - valid = true;
> - }
> -
> - input_report_abs(lradc->ts_input, ABS_PRESSURE, 0);
> - input_report_key(lradc->ts_input, BTN_TOUCH, 0);
> - input_sync(lradc->ts_input);
> -
> - /* Restart the touchscreen interrupts. */
> - mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ, LRADC_CTRL1);
> - mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
> -}
> -
> static int mxs_lradc_ts_open(struct input_dev *dev)
> {
> struct mxs_lradc *lradc = input_get_drvdata(dev);
>
_______________________________________________
devel mailing list
de...@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
