On 17/12/2020 19:06, Dmitry Osipenko wrote:
> Enable CPU voltage scaling and thermal throttling on Tegra20 Ventana board.
>
> Signed-off-by: Dmitry Osipenko <dig...@gmail.com>
> ---
> arch/arm/boot/dts/tegra20-ventana.dts | 40 ++++++++++++++++++++++++++-
> 1 file changed, 39 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm/boot/dts/tegra20-ventana.dts
> b/arch/arm/boot/dts/tegra20-ventana.dts
> index 14ace2ef749c..c2d9f38960bc 100644
> --- a/arch/arm/boot/dts/tegra20-ventana.dts
> +++ b/arch/arm/boot/dts/tegra20-ventana.dts
> @@ -2,8 +2,10 @@
> /dts-v1/;
>
> #include <dt-bindings/input/input.h>
> +#include <dt-bindings/thermal/thermal.h>
> #include "tegra20.dtsi"
> #include "tegra20-cpu-opp.dtsi"
> +#include "tegra20-cpu-opp-microvolt.dtsi"
>
> / {
> model = "NVIDIA Tegra20 Ventana evaluation board";
> @@ -527,9 +529,10 @@ ldo_rtc {
> };
> };
>
> - temperature-sensor@4c {
> + nct1008: temperature-sensor@4c {
> compatible = "onnn,nct1008";
> reg = <0x4c>;
> + #thermal-sensor-cells = <1>;
> };
> };
>
> @@ -615,10 +618,13 @@ clk32k_in: clock@0 {
>
> cpus {
> cpu0: cpu@0 {
> + cpu-supply = <&vdd_cpu>;
> operating-points-v2 = <&cpu0_opp_table>;
> + #cooling-cells = <2>;
> };
>
> cpu@1 {
> + cpu-supply = <&vdd_cpu>;
> operating-points-v2 = <&cpu0_opp_table>;
> };
> };
> @@ -717,4 +723,36 @@ sound {
> <&tegra_car TEGRA20_CLK_CDEV1>;
> clock-names = "pll_a", "pll_a_out0", "mclk";
> };
> +
> + thermal-zones {
> + cpu-thermal {
> + polling-delay-passive = <1000>; /* milliseconds */
> + polling-delay = <5000>; /* milliseconds */
> +
> + thermal-sensors = <&nct1008 1>;
> +
> + trips {
> + trip0: cpu-alert0 {
> + /* start throttling at 50C */
> + temperature = <50000>;
> + hysteresis = <200>;
Did you mean <2000> ?
> + type = "passive";
> + };
> +
> + trip1: cpu-crit {
> + /* shut down at 60C */
> + temperature = <60000>;
> + hysteresis = <2000>;
I think you can drop the hysteresis here, when the critical temperature
is reached, there is an emergency shutdown.
50°C and 60°C sound very low values, no ?
> + type = "critical";
> + };
> + };
> +
> + cooling-maps {
> + map0 {
> + trip = <&trip0>;
> + cooling-device = <&cpu0
> THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
You should add all CPUs here.
> + };
> + };
> + };
> + };
> };
>
--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
_______________________________________________
devel mailing list
de...@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
