On Tue, Jan 11, 2022 at 5:06 PM Xin Ji <x...@analogixsemi.com> wrote: > > Send DPCD command to downstream before anx7625 power down, > let downstream monitor enter into standby mode. > > Signed-off-by: Xin Ji <x...@analogixsemi.com> > --- > drivers/gpu/drm/bridge/analogix/anx7625.c | 42 +++++++++++++++++++---- > 1 file changed, 35 insertions(+), 7 deletions(-) > > diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.c > b/drivers/gpu/drm/bridge/analogix/anx7625.c > index 33383f83255d..0b858c78abe8 100644 > --- a/drivers/gpu/drm/bridge/analogix/anx7625.c > +++ b/drivers/gpu/drm/bridge/analogix/anx7625.c > @@ -129,6 +129,23 @@ static int anx7625_reg_write(struct anx7625_data *ctx, > return ret; > } > > +static int anx7625_reg_block_write(struct anx7625_data *ctx, > + struct i2c_client *client, > + u8 reg_addr, u8 len, u8 *buf) > +{ > + int ret; > + struct device *dev = &client->dev; > + > + i2c_access_workaround(ctx, client); > + > + ret = i2c_smbus_write_i2c_block_data(client, reg_addr, len, buf); > + if (ret < 0) > + dev_err(dev, "write i2c block failed id=%x\n:%x", > + client->addr, reg_addr); > + > + return ret; > +} > + > static int anx7625_write_or(struct anx7625_data *ctx, > struct i2c_client *client, > u8 offset, u8 mask) > @@ -214,8 +231,8 @@ static int wait_aux_op_finish(struct anx7625_data *ctx) > return 0; > } > > -static int anx7625_aux_dpcd_read(struct anx7625_data *ctx, > - u32 address, u8 len, u8 *buf) > +static int anx7625_aux_dpcd_trans(struct anx7625_data *ctx, u8 op, > + u32 address, u8 len, u8 *buf) > { > struct device *dev = &ctx->client->dev; > int ret; > @@ -231,8 +248,7 @@ static int anx7625_aux_dpcd_read(struct anx7625_data *ctx, > addrm = (address >> 8) & 0xFF; > addrh = (address >> 16) & 0xFF; > > - cmd = DPCD_CMD(len, DPCD_READ); > - cmd = ((len - 1) << 4) | 0x09; > + cmd = DPCD_CMD(len, op); > > /* Set command and length */ > ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, > @@ -246,6 +262,9 @@ static int anx7625_aux_dpcd_read(struct anx7625_data *ctx, > ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client, > AP_AUX_ADDR_19_16, addrh); > > + if (op == DPCD_WRITE) > + ret |= anx7625_reg_block_write(ctx, ctx->i2c.rx_p0_client, > + AP_AUX_BUFF_START, len, buf); > /* Enable aux access */ > ret |= anx7625_write_or(ctx, ctx->i2c.rx_p0_client, > AP_AUX_CTRL_STATUS, AP_AUX_CTRL_OP_EN); > @@ -255,14 +274,17 @@ static int anx7625_aux_dpcd_read(struct anx7625_data > *ctx, > return -EIO; > } > > - usleep_range(2000, 2100); > - > ret = wait_aux_op_finish(ctx); > if (ret) { > dev_err(dev, "aux IO error: wait aux op finish.\n"); > return ret; > } > > + /* Write done */ > + if (op == DPCD_WRITE) > + return 0; > + > + /* Read done, read out dpcd data */ > ret = anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client, > AP_AUX_BUFF_START, len, buf); > if (ret < 0) { > @@ -845,7 +867,7 @@ static int anx7625_hdcp_enable(struct anx7625_data *ctx) > } > > /* Read downstream capability */ > - anx7625_aux_dpcd_read(ctx, 0x68028, 1, &bcap); > + anx7625_aux_dpcd_trans(ctx, DPCD_READ, 0x68028, 1, &bcap); > if (!(bcap & 0x01)) { > pr_warn("downstream not support HDCP 1.4, cap(%x).\n", bcap); > return 0; > @@ -918,6 +940,7 @@ static void anx7625_dp_stop(struct anx7625_data *ctx) > { > struct device *dev = &ctx->client->dev; > int ret; > + u8 data; > > DRM_DEV_DEBUG_DRIVER(dev, "stop dp output\n"); > > @@ -929,6 +952,11 @@ static void anx7625_dp_stop(struct anx7625_data *ctx) > ret |= anx7625_write_and(ctx, ctx->i2c.tx_p2_client, 0x08, 0x7f); > > ret |= anx7625_video_mute_control(ctx, 1); > + > + dev_dbg(dev, "notify downstream enter into standby\n"); > + /* Downstream monitor enter into standby mode */ > + data = 2; > + ret |= anx7625_aux_dpcd_trans(ctx, DPCD_WRITE, 0x000600, 1, &data);
Is DPCD_READ/WRITE used for the same purpose as DP_AUX_NATIVE_WRITE/READ? If so, maybe you can just use DP_AUX_NATIVE_WRITE/READ and we don't need to define these values again in the driver? > if (ret < 0) > DRM_DEV_ERROR(dev, "IO error : mute video fail\n"); > > -- > 2.25.1 > _______________________________________________ devel mailing list de...@linuxdriverproject.org http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel