This member of the private data holds the start address of PCI BAR 1 that is
used to access the board registers. The start address is also stored in the
comedi_device 'iobase' member. Use that instead and remove the private data
member.
Remove some unnecessary casts when reading the board registers.
Signed-off-by: H Hartley Sweeten <hswee...@visionengravers.com>
Cc: Ian Abbott <abbo...@mev.co.uk>
Cc: Greg Kroah-Hartman <gre...@linuxfoundation.org>
---
.../comedi/drivers/addi-data/hwdrv_apci3120.c | 144 ++++++++++-----------
drivers/staging/comedi/drivers/addi_apci_3120.c | 2 -
2 files changed, 67 insertions(+), 79 deletions(-)
diff --git a/drivers/staging/comedi/drivers/addi-data/hwdrv_apci3120.c
b/drivers/staging/comedi/drivers/addi-data/hwdrv_apci3120.c
index d6875d9..0ba4b79 100644
--- a/drivers/staging/comedi/drivers/addi-data/hwdrv_apci3120.c
+++ b/drivers/staging/comedi/drivers/addi-data/hwdrv_apci3120.c
@@ -347,8 +347,7 @@ static int apci3120_ai_insn_read(struct comedi_device *dev,
* Testing if board have the new Quartz and calculate the time
value
* to set in the timer
*/
- us_TmpValue =
- (unsigned short) inw(devpriv->iobase +
APCI3120_RD_STATUS);
+ us_TmpValue = inw(dev->iobase + APCI3120_RD_STATUS);
/* EL250804: Testing if board APCI3120 have the new Quartz or
if it is an APCI3001 */
if ((us_TmpValue & 0x00B0) == 0x00B0
@@ -368,7 +367,7 @@ static int apci3120_ai_insn_read(struct comedi_device *dev,
/*
* Testing the interrupt flag and set the EOC bit
Clears the FIFO
*/
- inw(devpriv->iobase + APCI3120_RESET_FIFO);
+ inw(dev->iobase + APCI3120_RESET_FIFO);
/* Initialize the sequence array */
if (!apci3120_setup_chan_list(dev, s, 1,
@@ -381,7 +380,7 @@ static int apci3120_ai_insn_read(struct comedi_device *dev,
b_TimerSelectMode & 0xFC) |
APCI3120_TIMER_0_MODE_4;
outb(devpriv->b_TimerSelectMode,
- devpriv->iobase + APCI3120_TIMER_CRT1);
+ dev->iobase + APCI3120_TIMER_CRT1);
/* Reset the scan bit and Disables the EOS, DMA, EOC
interrupt */
devpriv->b_ModeSelectRegister =
@@ -396,7 +395,7 @@ static int apci3120_ai_insn_read(struct comedi_device *dev,
b_ModeSelectRegister &
APCI3120_DISABLE_EOS_INT) |
APCI3120_ENABLE_EOC_INT;
- inw(devpriv->iobase);
+ inw(dev->iobase + 0);
} else {
devpriv->b_ModeSelectRegister =
@@ -406,7 +405,7 @@ static int apci3120_ai_insn_read(struct comedi_device *dev,
}
outb(devpriv->b_ModeSelectRegister,
- devpriv->iobase + APCI3120_WRITE_MODE_SELECT);
+ dev->iobase + APCI3120_WRITE_MODE_SELECT);
/* Sets gate 0 */
devpriv->us_OutputRegister =
@@ -414,17 +413,17 @@ static int apci3120_ai_insn_read(struct comedi_device
*dev,
us_OutputRegister & APCI3120_CLEAR_PA_PR) |
APCI3120_ENABLE_TIMER0;
outw(devpriv->us_OutputRegister,
- devpriv->iobase + APCI3120_WR_ADDRESS);
+ dev->iobase + APCI3120_WR_ADDRESS);
/* Select Timer 0 */
b_Tmp = ((devpriv->
b_DigitalOutputRegister) & 0xF0) |
APCI3120_SELECT_TIMER_0_WORD;
- outb(b_Tmp, devpriv->iobase + APCI3120_TIMER_CRT0);
+ outb(b_Tmp, dev->iobase + APCI3120_TIMER_CRT0);
/* Set the conversion time */
outw(us_ConvertTiming,
- devpriv->iobase + APCI3120_TIMER_VALUE);
+ dev->iobase + APCI3120_TIMER_VALUE);
us_TmpValue =
(unsigned short) inw(dev->iobase +
APCI3120_RD_STATUS);
@@ -433,26 +432,25 @@ static int apci3120_ai_insn_read(struct comedi_device
*dev,
do {
/* Waiting for the end of conversion */
- us_TmpValue =
- inw(devpriv->iobase +
- APCI3120_RD_STATUS);
+ us_TmpValue = inw(dev->iobase +
+ APCI3120_RD_STATUS);
} while ((us_TmpValue & APCI3120_EOC) ==
APCI3120_EOC);
/* Read the result in FIFO and put it in insn
data pointer */
- us_TmpValue = inw(devpriv->iobase + 0);
+ us_TmpValue = inw(dev->iobase + 0);
*data = us_TmpValue;
- inw(devpriv->iobase + APCI3120_RESET_FIFO);
+ inw(dev->iobase + APCI3120_RESET_FIFO);
}
break;
case APCI3120_EOS_MODE:
- inw(devpriv->iobase);
+ inw(dev->iobase + 0);
/* Clears the FIFO */
- inw(devpriv->iobase + APCI3120_RESET_FIFO);
+ inw(dev->iobase + APCI3120_RESET_FIFO);
/* clear PA PR and disable timer 0 */
devpriv->us_OutputRegister =
@@ -461,7 +459,7 @@ static int apci3120_ai_insn_read(struct comedi_device *dev,
APCI3120_DISABLE_TIMER0;
outw(devpriv->us_OutputRegister,
- devpriv->iobase + APCI3120_WR_ADDRESS);
+ dev->iobase + APCI3120_WR_ADDRESS);
if (!apci3120_setup_chan_list(dev, s,
devpriv->ui_AiNbrofChannels,
@@ -474,24 +472,24 @@ static int apci3120_ai_insn_read(struct comedi_device
*dev,
b_TimerSelectMode & 0xFC) |
APCI3120_TIMER_0_MODE_2;
outb(devpriv->b_TimerSelectMode,
- devpriv->iobase + APCI3120_TIMER_CRT1);
+ dev->iobase + APCI3120_TIMER_CRT1);
/* Select Timer 0 */
b_Tmp = ((devpriv->
b_DigitalOutputRegister) & 0xF0) |
APCI3120_SELECT_TIMER_0_WORD;
- outb(b_Tmp, devpriv->iobase + APCI3120_TIMER_CRT0);
+ outb(b_Tmp, dev->iobase + APCI3120_TIMER_CRT0);
/* Set the conversion time */
outw(us_ConvertTiming,
- devpriv->iobase + APCI3120_TIMER_VALUE);
+ dev->iobase + APCI3120_TIMER_VALUE);
/* Set the scan bit */
devpriv->b_ModeSelectRegister =
devpriv->
b_ModeSelectRegister | APCI3120_ENABLE_SCAN;
outb(devpriv->b_ModeSelectRegister,
- devpriv->iobase + APCI3120_WRITE_MODE_SELECT);
+ dev->iobase + APCI3120_WRITE_MODE_SELECT);
/* If Interrupt function is loaded */
if (devpriv->b_EocEosInterrupt == APCI3120_ENABLE) {
@@ -501,7 +499,7 @@ static int apci3120_ai_insn_read(struct comedi_device *dev,
b_ModeSelectRegister &
APCI3120_DISABLE_EOC_INT) |
APCI3120_ENABLE_EOS_INT;
- inw(devpriv->iobase);
+ inw(dev->iobase + 0);
} else
devpriv->b_ModeSelectRegister =
@@ -510,34 +508,33 @@ static int apci3120_ai_insn_read(struct comedi_device
*dev,
APCI3120_DISABLE_ALL_INTERRUPT_WITHOUT_TIMER;
outb(devpriv->b_ModeSelectRegister,
- devpriv->iobase + APCI3120_WRITE_MODE_SELECT);
+ dev->iobase + APCI3120_WRITE_MODE_SELECT);
- inw(devpriv->iobase + APCI3120_RD_STATUS);
+ inw(dev->iobase + APCI3120_RD_STATUS);
/* Sets gate 0 */
devpriv->us_OutputRegister =
devpriv->
us_OutputRegister | APCI3120_ENABLE_TIMER0;
outw(devpriv->us_OutputRegister,
- devpriv->iobase + APCI3120_WR_ADDRESS);
+ dev->iobase + APCI3120_WR_ADDRESS);
/* Start conversion */
- outw(0, devpriv->iobase + APCI3120_START_CONVERSION);
+ outw(0, dev->iobase + APCI3120_START_CONVERSION);
/* Waiting of end of conversion if interrupt is not
installed */
if (devpriv->b_EocEosInterrupt == APCI3120_DISABLE) {
/* Waiting the end of conversion */
do {
- us_TmpValue =
- inw(devpriv->iobase +
- APCI3120_RD_STATUS);
+ us_TmpValue = inw(dev->iobase +
+ APCI3120_RD_STATUS);
} while ((us_TmpValue & APCI3120_EOS) !=
APCI3120_EOS);
for (i = 0; i < devpriv->ui_AiNbrofChannels;
i++) {
/* Read the result in FIFO and write
them in shared memory */
- us_TmpValue = inw(devpriv->iobase);
+ us_TmpValue = inw(dev->iobase);
data[i] = (unsigned int) us_TmpValue;
}
@@ -787,7 +784,7 @@ static int apci3120_cyclic_ai(int mode,
/* Resets the FIFO */
/* BEGIN JK 07.05.04: Comparison between WIN32 and Linux driver */
- inb(devpriv->iobase + APCI3120_RESET_FIFO);
+ inb(dev->iobase + APCI3120_RESET_FIFO);
/* END JK 07.05.04: Comparison between WIN32 and Linux driver */
devpriv->ui_AiActualScan = 0;
@@ -1392,7 +1389,7 @@ static irqreturn_t apci3120_interrupt(int irq, void *d)
devpriv->b_ExttrigEnable = APCI3120_DISABLE;
}
/* clear the timer 2 interrupt */
- inb(devpriv->iobase + APCI3120_TIMER_STATUS_REGISTER);
+ inb(dev->iobase + APCI3120_TIMER_STATUS_REGISTER);
if (int_amcc & MASTER_ABORT_INT)
dev_err(dev->class_dev, "AMCC IRQ - MASTER DMA ABORT!\n");
@@ -1405,8 +1402,7 @@ static irqreturn_t apci3120_interrupt(int irq, void *d)
if (devpriv->b_EocEosInterrupt == APCI3120_ENABLE) {
/* Read the AI Value */
- devpriv->ui_AiReadData[0] =
- (unsigned int) inw(devpriv->iobase + 0);
+ devpriv->ui_AiReadData[0] = inw(dev->iobase + 0);
devpriv->b_EocEosInterrupt = APCI3120_DISABLE;
send_sig(SIGIO, devpriv->tsk_Current, 0); /*
send signal to the sample */
} else {
@@ -1415,8 +1411,7 @@ static irqreturn_t apci3120_interrupt(int irq, void *d)
devpriv->
b_ModeSelectRegister & APCI3120_DISABLE_EOC_INT;
outb(devpriv->b_ModeSelectRegister,
- devpriv->iobase + APCI3120_WRITE_MODE_SELECT);
-
+ dev->iobase + APCI3120_WRITE_MODE_SELECT);
}
}
@@ -1440,7 +1435,7 @@ static irqreturn_t apci3120_interrupt(int irq, void *d)
ui_Check = 0;
for (i = 0; i < devpriv->ui_AiNbrofChannels;
i++) {
- us_TmpValue = inw(devpriv->iobase + 0);
+ us_TmpValue = inw(dev->iobase + 0);
devpriv->ui_AiReadData[i] =
(unsigned int) us_TmpValue;
}
@@ -1562,7 +1557,7 @@ static int apci3120_config_insn_timer(struct
comedi_device *dev,
ui_Timervalue2 = data[1] / 1000; /* convert nano seconds to u
seconds */
- us_TmpValue = (unsigned short) inw(devpriv->iobase +
APCI3120_RD_STATUS);
+ us_TmpValue = inw(dev->iobase + APCI3120_RD_STATUS);
/*
* EL250804: Testing if board APCI3120 have the new Quartz or if it
@@ -1580,7 +1575,7 @@ static int apci3120_config_insn_timer(struct
comedi_device *dev,
/* Reset gate 2 of Timer 2 to disable it (Set Bit D14 to 0) */
devpriv->us_OutputRegister =
devpriv->us_OutputRegister & APCI3120_DISABLE_TIMER2;
- outw(devpriv->us_OutputRegister, devpriv->iobase + APCI3120_WR_ADDRESS);
+ outw(devpriv->us_OutputRegister, dev->iobase + APCI3120_WR_ADDRESS);
/* Disable TIMER Interrupt */
devpriv->b_ModeSelectRegister =
@@ -1593,14 +1588,14 @@ static int apci3120_config_insn_timer(struct
comedi_device *dev,
b_ModeSelectRegister & APCI3120_DISABLE_EOC_INT &
APCI3120_DISABLE_EOS_INT;
outb(devpriv->b_ModeSelectRegister,
- devpriv->iobase + APCI3120_WRITE_MODE_SELECT);
+ dev->iobase + APCI3120_WRITE_MODE_SELECT);
if (data[0] == APCI3120_TIMER) { /* initialize timer */
/* Set the Timer 2 in mode 2(Timer) */
devpriv->b_TimerSelectMode =
(devpriv->
b_TimerSelectMode & 0x0F) | APCI3120_TIMER_2_MODE_2;
outb(devpriv->b_TimerSelectMode,
- devpriv->iobase + APCI3120_TIMER_CRT1);
+ dev->iobase + APCI3120_TIMER_CRT1);
/*
* Configure the timer 2 for writing the LOW unsigned short of
timer
@@ -1614,17 +1609,17 @@ static int apci3120_config_insn_timer(struct
comedi_device *dev,
b_Tmp = ((devpriv->
b_DigitalOutputRegister) & 0xF0) |
APCI3120_SELECT_TIMER_2_LOW_WORD;
- outb(b_Tmp, devpriv->iobase + APCI3120_TIMER_CRT0);
+ outb(b_Tmp, dev->iobase + APCI3120_TIMER_CRT0);
outw(ui_Timervalue2 & 0xffff,
- devpriv->iobase + APCI3120_TIMER_VALUE);
+ dev->iobase + APCI3120_TIMER_VALUE);
/* Writing HIGH unsigned short */
b_Tmp = ((devpriv->
b_DigitalOutputRegister) & 0xF0) |
APCI3120_SELECT_TIMER_2_HIGH_WORD;
- outb(b_Tmp, devpriv->iobase + APCI3120_TIMER_CRT0);
+ outb(b_Tmp, dev->iobase + APCI3120_TIMER_CRT0);
outw((ui_Timervalue2 >> 16) & 0xffff,
- devpriv->iobase + APCI3120_TIMER_VALUE);
+ dev->iobase + APCI3120_TIMER_VALUE);
/* timer2 in Timer mode enabled */
devpriv->b_Timer2Mode = APCI3120_TIMER;
@@ -1635,7 +1630,7 @@ static int apci3120_config_insn_timer(struct
comedi_device *dev,
(devpriv->
b_TimerSelectMode & 0x0F) | APCI3120_TIMER_2_MODE_5;
outb(devpriv->b_TimerSelectMode,
- devpriv->iobase + APCI3120_TIMER_CRT1);
+ dev->iobase + APCI3120_TIMER_CRT1);
/*
* Configure the timer 2 for writing the LOW unsigned short of
timer
@@ -1649,18 +1644,18 @@ static int apci3120_config_insn_timer(struct
comedi_device *dev,
b_Tmp = ((devpriv->
b_DigitalOutputRegister) & 0xF0) |
APCI3120_SELECT_TIMER_2_LOW_WORD;
- outb(b_Tmp, devpriv->iobase + APCI3120_TIMER_CRT0);
+ outb(b_Tmp, dev->iobase + APCI3120_TIMER_CRT0);
outw(ui_Timervalue2 & 0xffff,
- devpriv->iobase + APCI3120_TIMER_VALUE);
+ dev->iobase + APCI3120_TIMER_VALUE);
/* Writing HIGH unsigned short */
b_Tmp = ((devpriv->
b_DigitalOutputRegister) & 0xF0) |
APCI3120_SELECT_TIMER_2_HIGH_WORD;
- outb(b_Tmp, devpriv->iobase + APCI3120_TIMER_CRT0);
+ outb(b_Tmp, dev->iobase + APCI3120_TIMER_CRT0);
outw((ui_Timervalue2 >> 16) & 0xffff,
- devpriv->iobase + APCI3120_TIMER_VALUE);
+ dev->iobase + APCI3120_TIMER_VALUE);
/* watchdog enabled */
devpriv->b_Timer2Mode = APCI3120_WATCHDOG;
@@ -1715,7 +1710,7 @@ static int apci3120_write_insn_timer(struct comedi_device
*dev,
case APCI3120_START:
/* Reset FC_TIMER BIT */
- inb(devpriv->iobase + APCI3120_TIMER_STATUS_REGISTER);
+ inb(dev->iobase + APCI3120_TIMER_STATUS_REGISTER);
if (devpriv->b_Timer2Mode == APCI3120_TIMER) { /* start timer
*/
/* Enable Timer */
devpriv->b_ModeSelectRegister =
@@ -1745,7 +1740,7 @@ static int apci3120_write_insn_timer(struct comedi_device
*dev,
APCI3120_DISABLE_TIMER_INT;
}
outb(devpriv->b_ModeSelectRegister,
- devpriv->iobase + APCI3120_WRITE_MODE_SELECT);
+ dev->iobase + APCI3120_WRITE_MODE_SELECT);
if (devpriv->b_Timer2Mode == APCI3120_TIMER) { /* start timer
*/
/* For Timer mode is Gate2 must be activated timer
started */
@@ -1753,7 +1748,7 @@ static int apci3120_write_insn_timer(struct comedi_device
*dev,
devpriv->
us_OutputRegister | APCI3120_ENABLE_TIMER2;
outw(devpriv->us_OutputRegister,
- devpriv->iobase + APCI3120_WR_ADDRESS);
+ dev->iobase + APCI3120_WR_ADDRESS);
}
break;
@@ -1779,16 +1774,16 @@ static int apci3120_write_insn_timer(struct
comedi_device *dev,
/* Write above states to register */
outb(devpriv->b_ModeSelectRegister,
- devpriv->iobase + APCI3120_WRITE_MODE_SELECT);
+ dev->iobase + APCI3120_WRITE_MODE_SELECT);
/* Reset Gate 2 */
devpriv->us_OutputRegister =
devpriv->us_OutputRegister & APCI3120_DISABLE_TIMER_INT;
outw(devpriv->us_OutputRegister,
- devpriv->iobase + APCI3120_WR_ADDRESS);
+ dev->iobase + APCI3120_WR_ADDRESS);
/* Reset FC_TIMER BIT */
- inb(devpriv->iobase + APCI3120_TIMER_STATUS_REGISTER);
+ inb(dev->iobase + APCI3120_TIMER_STATUS_REGISTER);
break;
@@ -1798,8 +1793,7 @@ static int apci3120_write_insn_timer(struct comedi_device
*dev,
"timer2 not configured in TIMER MODE\n");
return -EINVAL;
}
- us_TmpValue =
- (unsigned short) inw(devpriv->iobase +
APCI3120_RD_STATUS);
+ us_TmpValue = inw(dev->iobase + APCI3120_RD_STATUS);
/*
* EL250804: Testing if board APCI3120 have the new Quartz or
if it
@@ -1817,19 +1811,19 @@ static int apci3120_write_insn_timer(struct
comedi_device *dev,
b_Tmp = ((devpriv->
b_DigitalOutputRegister) & 0xF0) |
APCI3120_SELECT_TIMER_2_LOW_WORD;
- outb(b_Tmp, devpriv->iobase + APCI3120_TIMER_CRT0);
+ outb(b_Tmp, dev->iobase + APCI3120_TIMER_CRT0);
outw(ui_Timervalue2 & 0xffff,
- devpriv->iobase + APCI3120_TIMER_VALUE);
+ dev->iobase + APCI3120_TIMER_VALUE);
/* Writing HIGH unsigned short */
b_Tmp = ((devpriv->
b_DigitalOutputRegister) & 0xF0) |
APCI3120_SELECT_TIMER_2_HIGH_WORD;
- outb(b_Tmp, devpriv->iobase + APCI3120_TIMER_CRT0);
+ outb(b_Tmp, dev->iobase + APCI3120_TIMER_CRT0);
outw((ui_Timervalue2 >> 16) & 0xffff,
- devpriv->iobase + APCI3120_TIMER_VALUE);
+ dev->iobase + APCI3120_TIMER_VALUE);
break;
default:
@@ -1866,29 +1860,29 @@ static int apci3120_read_insn_timer(struct
comedi_device *dev,
b_Tmp = ((devpriv->
b_DigitalOutputRegister) & 0xF0) |
APCI3120_SELECT_TIMER_2_LOW_WORD;
- outb(b_Tmp, devpriv->iobase + APCI3120_TIMER_CRT0);
+ outb(b_Tmp, dev->iobase + APCI3120_TIMER_CRT0);
- us_TmpValue = inw(devpriv->iobase + APCI3120_TIMER_VALUE);
+ us_TmpValue = inw(dev->iobase + APCI3120_TIMER_VALUE);
/* Read the HIGH unsigned short of Timer 2 register */
b_Tmp = ((devpriv->
b_DigitalOutputRegister) & 0xF0) |
APCI3120_SELECT_TIMER_2_HIGH_WORD;
- outb(b_Tmp, devpriv->iobase + APCI3120_TIMER_CRT0);
+ outb(b_Tmp, dev->iobase + APCI3120_TIMER_CRT0);
- us_TmpValue_2 = inw(devpriv->iobase + APCI3120_TIMER_VALUE);
+ us_TmpValue_2 = inw(dev->iobase + APCI3120_TIMER_VALUE);
/* combining both words */
data[0] = (unsigned int) ((us_TmpValue) | ((us_TmpValue_2) <<
16));
} else { /* Read watch dog status */
- us_StatusValue = inw(devpriv->iobase + APCI3120_RD_STATUS);
+ us_StatusValue = inw(dev->iobase + APCI3120_RD_STATUS);
us_StatusValue =
((us_StatusValue & APCI3120_FC_TIMER) >> 12) & 1;
if (us_StatusValue == 1) {
/* RESET FC_TIMER BIT */
- inb(devpriv->iobase + APCI3120_TIMER_STATUS_REGISTER);
+ inb(dev->iobase + APCI3120_TIMER_STATUS_REGISTER);
}
data[0] = us_StatusValue; /* when data[0] = 1 then the
watch dog has rundown */
}
@@ -1900,11 +1894,10 @@ static int apci3120_di_insn_bits(struct comedi_device
*dev,
struct comedi_insn *insn,
unsigned int *data)
{
- struct apci3120_private *devpriv = dev->private;
unsigned int val;
/* the input channels are bits 11:8 of the status reg */
- val = inw(devpriv->iobase + APCI3120_RD_STATUS);
+ val = inw(dev->iobase + APCI3120_RD_STATUS);
data[1] = (val >> 8) & 0xf;
return insn->n;
@@ -1922,7 +1915,7 @@ static int apci3120_do_insn_bits(struct comedi_device
*dev,
devpriv->b_DigitalOutputRegister = s->state << 4;
outb(devpriv->b_DigitalOutputRegister,
- devpriv->iobase + APCI3120_DIGITAL_OUTPUT);
+ dev->iobase + APCI3120_DIGITAL_OUTPUT);
}
data[1] = s->state;
@@ -1935,7 +1928,6 @@ static int apci3120_ao_insn_write(struct comedi_device
*dev,
struct comedi_insn *insn,
unsigned int *data)
{
- struct apci3120_private *devpriv = dev->private;
unsigned int ui_Channel;
unsigned short us_TmpValue;
@@ -1944,9 +1936,7 @@ static int apci3120_ao_insn_write(struct comedi_device
*dev,
data[0] = ((((ui_Channel & 0x03) << 14) & 0xC000) | data[0]);
do { /* Waiting of DA_READY BIT */
- us_TmpValue =
- ((unsigned short) inw(devpriv->iobase +
- APCI3120_RD_STATUS)) & 0x0001;
+ us_TmpValue = inw(dev->iobase + APCI3120_RD_STATUS) & 0x0001;
} while (us_TmpValue != 0x0001);
if (ui_Channel <= 3)
@@ -1955,14 +1945,14 @@ static int apci3120_ao_insn_write(struct comedi_device
*dev,
* typecasted to ushort since word write is to be done
*/
outw((unsigned short) data[0],
- devpriv->iobase + APCI3120_ANALOG_OUTPUT_1);
+ dev->iobase + APCI3120_ANALOG_OUTPUT_1);
else
/*
* for channel 4-7 out at the register 2 (wrDac5-8) data[i]
* typecasted to ushort since word write is to be done
*/
outw((unsigned short) data[0],
- devpriv->iobase + APCI3120_ANALOG_OUTPUT_2);
+ dev->iobase + APCI3120_ANALOG_OUTPUT_2);
return insn->n;
}
diff --git a/drivers/staging/comedi/drivers/addi_apci_3120.c
b/drivers/staging/comedi/drivers/addi_apci_3120.c
index c6f3bc9..6b4a51d 100644
--- a/drivers/staging/comedi/drivers/addi_apci_3120.c
+++ b/drivers/staging/comedi/drivers/addi_apci_3120.c
@@ -37,7 +37,6 @@ struct apci3120_dmabuf {
};
struct apci3120_private {
- int iobase;
unsigned long amcc;
unsigned long addon;
unsigned int ui_AiActualScan;
@@ -136,7 +135,6 @@ static int apci3120_auto_attach(struct comedi_device *dev,
pci_set_master(pcidev);
dev->iobase = pci_resource_start(pcidev, 1);
- devpriv->iobase = dev->iobase;
devpriv->amcc = pci_resource_start(pcidev, 0);
devpriv->addon = pci_resource_start(pcidev, 2);
--
2.0.3
_______________________________________________
devel mailing list
de...@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
