Hi Florian,
On 28.11.2016 05:56, Florian Fainelli wrote:
> On 11/26/2016 04:20 AM, Lino Sanfilippo wrote:
>> Add driver for Alacritech gigabit ethernet cards with SLIC (session-layer
>> interface control) technology. The driver provides basic support without
>> SLIC for the following devices:
>>
>> - Mojave cards (single port PCI Gigabit) both copper and fiber
>> - Oasis cards (single and dual port PCI-x Gigabit) copper and fiber
>> - Kalahari cards (dual and quad port PCI-e Gigabit) copper and fiber
>
> This looks great, a few nits below:
>
>
>> +#define SLIC_MAX_TX_COMPLETIONS 100
>
> You usually don't want to limit the number of TX completion, if the
> entire TX ring needs to be cleaned, you would want to allow that.
>
The problem is that the HW does not provide a tx completion index. Instead we
have to
iterate the status descriptors until we get an invalid idx which indicates that
there
are no further tx descriptors done for now. I am afraid that if we do not limit
the
number of descriptors processed in the tx completion handler, a continuous
transmission
of frames could keep the loop in xmit_complete() run endlessly. I dont know if
this
can actually happen but I wanted to make sure that this is avoided.
> [snip]
>
>> + while (slic_get_free_rx_descs(rxq) > SLIC_MAX_REQ_RX_DESCS) {
>> + skb = alloc_skb(maplen + ALIGN_MASK, gfp);
>> + if (!skb)
>> + break;
>> +
>> + paddr = dma_map_single(&sdev->pdev->dev, skb->data, maplen,
>> + DMA_FROM_DEVICE);
>> + if (dma_mapping_error(&sdev->pdev->dev, paddr)) {
>> + netdev_err(dev, "mapping rx packet failed\n");
>> + /* drop skb */
>> + dev_kfree_skb_any(skb);
>> + break;
>> + }
>> + /* ensure head buffer descriptors are 256 byte aligned */
>> + offset = 0;
>> + misalign = paddr & ALIGN_MASK;
>> + if (misalign) {
>> + offset = SLIC_RX_BUFF_ALIGN - misalign;
>> + skb_reserve(skb, offset);
>> + }
>> + /* the HW expects dma chunks for descriptor + frame data */
>> + desc = (struct slic_rx_desc *)skb->data;
>> + memset(desc, 0, sizeof(*desc));
>
> Do you really need to zero-out the prepending RX descriptor? Are not you
> missing a write barrier here?
Indeed, it should be sufficient to make sure that the bit SLIC_IRHDDR_SVALID is
not set.
I will adjust it.
Concerning the write barrier: You mean a wmb() before slic_write() to ensure
that the zeroing
of the status desc is done before the descriptor is passed to the HW, right?
> [snip]
>
>> +
>> + dma_sync_single_for_cpu(&sdev->pdev->dev,
>> + dma_unmap_addr(buff, map_addr),
>> + buff->addr_offset + sizeof(*desc),
>> + DMA_FROM_DEVICE);
>> +
>> + status = le32_to_cpu(desc->status);
>> + if (!(status & SLIC_IRHDDR_SVALID))
>> + break;
>> +
>> + buff->skb = NULL;
>> +
>> + dma_unmap_single(&sdev->pdev->dev,
>> + dma_unmap_addr(buff, map_addr),
>> + dma_unmap_len(buff, map_len),
>> + DMA_FROM_DEVICE);
>
> This is potentially inefficient, you already did a cache invalidation
> for the RX descriptor here, you could be more efficient with just
> invalidating the packet length, minus the descriptor length.
>
I am not sure I understand: We have to unmap the complete dma area, no matter
if we synced
part of it before, dont we? AFAIK a dma sync is different from unmapping dma,
or do I miss
something?
>> +
>> + /* skip rx descriptor that is placed before the frame data */
>> + skb_reserve(skb, SLIC_RX_BUFF_HDR_SIZE);
>> +
>> + if (unlikely(status & SLIC_IRHDDR_ERR)) {
>> + slic_handle_frame_error(sdev, skb);
>> + dev_kfree_skb_any(skb);
>> + } else {
>> + struct ethhdr *eh = (struct ethhdr *)skb->data;
>> +
>> + if (is_multicast_ether_addr(eh->h_dest))
>> + SLIC_INC_STATS_COUNTER(&sdev->stats, rx_mcasts);
>> +
>> + len = le32_to_cpu(desc->length) & SLIC_IRHDDR_FLEN_MSK;
>> + skb_put(skb, len);
>> + skb->protocol = eth_type_trans(skb, dev);
>> + skb->ip_summed = CHECKSUM_UNNECESSARY;
>> + skb->dev = dev;
>
> eth_type_trans() already assigns skb->dev = dev;
>
Right, this is unnecessary, I will fix it.
>> +static int slic_poll(struct napi_struct *napi, int todo)
>> +{
>> + struct slic_device *sdev = container_of(napi, struct slic_device, napi);
>> + struct slic_shmem *sm = &sdev->shmem;
>> + struct slic_shmem_data *sm_data = sm->shmem_data;
>> + u32 isr = le32_to_cpu(sm_data->isr);
>> + unsigned int done = 0;
>> +
>> + slic_handle_irq(sdev, isr, todo, &done);
>> +
>> + if (done < todo) {
>> + napi_complete(napi);
>
> napi_complete_done() since you know how many packets you completed.
>
Ok, will change it.
>> + /* reenable irqs */
>> + sm_data->isr = 0;
>> + /* make sure sm_data->isr is cleard before irqs are reenabled */
>> + wmb();
>> + slic_write(sdev, SLIC_REG_ISR, 0);
>> + slic_flush_write(sdev);
>> + }
>> +
>> + return done;
>> +}
>> +
>> +static irqreturn_t slic_irq(int irq, void *dev_id)
>> +{
>> + struct slic_device *sdev = dev_id;
>> + struct slic_shmem *sm = &sdev->shmem;
>> + struct slic_shmem_data *sm_data = sm->shmem_data;
>> +
>> + slic_write(sdev, SLIC_REG_ICR, SLIC_ICR_INT_MASK);
>> + slic_flush_write(sdev);
>> + /* make sure sm_data->isr is read after ICR_INT_MASK is set */
>> + wmb();
>> +
>> + if (!sm_data->isr) {
>> + dma_rmb();
>> + /* spurious interrupt */
>> + slic_write(sdev, SLIC_REG_ISR, 0);
>> + slic_flush_write(sdev);
>> + return IRQ_NONE;
>> + }
>> +
>> + napi_schedule(&sdev->napi);
>
> Likewise napi_schedule_irqoff() can be used here.
>
Ok, will change it.
Thanks a lot Florian!
Regards,
Lino
_______________________________________________
devel mailing list
de...@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
