On 01/03/2017 10:57 PM, Steve Longerbeam wrote: > Enables the ADV7180 decoder sensor. The ADV7180 connects to the > parallel-bus mux input on ipu1_csi0_mux. > > On the sabreauto, two analog video inputs are routed to the ADV7180, > composite on Ain1, and composite on Ain3. Those inputs are defined > via inputs and input-names under the ADV7180 node. The ADV7180 power > pin is via max7310_b port expander. > > Signed-off-by: Steve Longerbeam <steve_longerb...@mentor.com> > --- > arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 56 > ++++++++++++++++++++++++++++++++ > 1 file changed, 56 insertions(+) > > diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi > b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi > index 83ac2ff..30ee378 100644 > --- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi > +++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi > @@ -147,10 +147,42 @@ > gpio-controller; > #gpio-cells = <2>; > }; > + > + camera: adv7180@21 {
adv7180: camera@21 > + compatible = "adi,adv7180"; > + reg = <0x21>; > + powerdown-gpios = <&max7310_b 2 > GPIO_ACTIVE_LOW>; > + interrupt-parent = <&gpio1>; > + interrupts = <27 0x8>; > + inputs = <0x00 0x02>; > + input-names = "ADV7180 Composite on Ain1", > + "ADV7180 Composite on Ain3"; > + > + port { > + adv7180_to_ipu1_csi0_mux: endpoint { > + remote-endpoint = > <&ipu1_csi0_mux_from_parallel_sensor>; > + bus-width = <8>; > + }; > + }; > + }; > }; > }; > }; > > +&ipu1_csi0_from_ipu1_csi0_mux { > + bus-width = <8>; > +}; > + > +&ipu1_csi0_mux_from_parallel_sensor { > + remote-endpoint = <&adv7180_to_ipu1_csi0_mux>; > + bus-width = <8>; > +}; > + > +&ipu1_csi0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_ipu1_csi0>; > +}; > + > &clks { > assigned-clocks = <&clks IMX6QDL_PLL4_BYPASS_SRC>, > <&clks IMX6QDL_PLL4_BYPASS>, > @@ -451,6 +483,30 @@ > >; > }; > > + pinctrl_ipu1_csi0: ipu1grp-csi0 { Please rename node name to ipu1csi0grp. > + fsl,pins = < > + MX6QDL_PAD_CSI0_DAT4__IPU1_CSI0_DATA04 > 0x80000000 > + MX6QDL_PAD_CSI0_DAT5__IPU1_CSI0_DATA05 > 0x80000000 > + MX6QDL_PAD_CSI0_DAT6__IPU1_CSI0_DATA06 > 0x80000000 > + MX6QDL_PAD_CSI0_DAT7__IPU1_CSI0_DATA07 > 0x80000000 > + MX6QDL_PAD_CSI0_DAT8__IPU1_CSI0_DATA08 > 0x80000000 > + MX6QDL_PAD_CSI0_DAT9__IPU1_CSI0_DATA09 > 0x80000000 > + MX6QDL_PAD_CSI0_DAT10__IPU1_CSI0_DATA10 > 0x80000000 > + MX6QDL_PAD_CSI0_DAT11__IPU1_CSI0_DATA11 > 0x80000000 > + MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 > 0x80000000 > + MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 > 0x80000000 > + MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 > 0x80000000 > + MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 > 0x80000000 > + MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 > 0x80000000 > + MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 > 0x80000000 > + MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 > 0x80000000 > + MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 > 0x80000000 > + MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK > 0x80000000 > + MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC > 0x80000000 > + MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC > 0x80000000 > + >; > + }; > + > pinctrl_pwm3: pwm1grp { > fsl,pins = < > MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1 > -- With best wishes, Vladimir _______________________________________________ devel mailing list de...@linuxdriverproject.org http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel