On Thu, 6 Jul 2017 18:56:22 -0400
Brian Masney <masn...@onstation.org> wrote:
> The calibration function calls i2c_smbus_write_byte() and
> i2c_smbus_read_byte(). These two function calls are replaced with a
> single call to i2c_smbus_read_byte_data() by this patch. This patch
> also removes an unnecessary call that reads the CNTRL register
> a second time. One of the error paths returned -1 if the ADC was not
> enabled and this patch changes that return value to -EINVAL.
>
> Signed-off-by: Brian Masney <masn...@onstation.org>
Applied.
> ---
> drivers/staging/iio/light/tsl2x7x.c | 34 ++++++++++++----------------------
> 1 file changed, 12 insertions(+), 22 deletions(-)
>
> diff --git a/drivers/staging/iio/light/tsl2x7x.c
> b/drivers/staging/iio/light/tsl2x7x.c
> index 6c9f06b..5734628 100644
> --- a/drivers/staging/iio/light/tsl2x7x.c
> +++ b/drivers/staging/iio/light/tsl2x7x.c
> @@ -542,39 +542,29 @@ static void tsl2x7x_defaults(struct tsl2X7X_chip *chip)
> static int tsl2x7x_als_calibrate(struct iio_dev *indio_dev)
> {
> struct tsl2X7X_chip *chip = iio_priv(indio_dev);
> - u8 reg_val;
> int gain_trim_val;
> int ret;
> int lux_val;
>
> - ret = i2c_smbus_write_byte(chip->client,
> - (TSL2X7X_CMD_REG | TSL2X7X_CNTRL));
> + ret = i2c_smbus_read_byte_data(chip->client,
> + TSL2X7X_CMD_REG | TSL2X7X_CNTRL);
> if (ret < 0) {
> dev_err(&chip->client->dev,
> - "failed to write CNTRL register, ret=%d\n", ret);
> + "%s: failed to read from the CNTRL register\n",
> + __func__);
> return ret;
> }
>
> - reg_val = i2c_smbus_read_byte(chip->client);
> - if ((reg_val & (TSL2X7X_CNTL_ADC_ENBL | TSL2X7X_CNTL_PWR_ON))
> - != (TSL2X7X_CNTL_ADC_ENBL | TSL2X7X_CNTL_PWR_ON)) {
> - dev_err(&chip->client->dev,
> - "%s: failed: ADC not enabled\n", __func__);
> - return -1;
> - }
> -
> - ret = i2c_smbus_write_byte(chip->client,
> - (TSL2X7X_CMD_REG | TSL2X7X_CNTRL));
> - if (ret < 0) {
> + if ((ret & (TSL2X7X_CNTL_ADC_ENBL | TSL2X7X_CNTL_PWR_ON))
> + != (TSL2X7X_CNTL_ADC_ENBL | TSL2X7X_CNTL_PWR_ON)) {
> dev_err(&chip->client->dev,
> - "failed to write ctrl reg: ret=%d\n", ret);
> - return ret;
> - }
> -
> - reg_val = i2c_smbus_read_byte(chip->client);
> - if ((reg_val & TSL2X7X_STA_ADC_VALID) != TSL2X7X_STA_ADC_VALID) {
> + "%s: Device is not powered on and/or ADC is not
> enabled\n",
> + __func__);
> + return -EINVAL;
> + } else if ((ret & TSL2X7X_STA_ADC_VALID) != TSL2X7X_STA_ADC_VALID) {
> dev_err(&chip->client->dev,
> - "%s: failed: STATUS - ADC not valid.\n", __func__);
> + "%s: The two ADC channels have not completed an
> integration cycle\n",
> + __func__);
> return -ENODATA;
> }
>
_______________________________________________
devel mailing list
de...@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
