Am 11.12.2017 um 20:40 schrieb Oliver Graute:
Hello list,
I just got my pi433 working somehow on Raspberry Pi Model B Rev 2.
Here are my findings:
first I need to enabling spi in config.txt on boot partition.
dtparam=spi=on
then adding this node to bcm2835-rpi-b-rev2.dts and compile.
&spi0_gpio7 {
pi433: pi433@0 {
compatible = "Smarthome-Wolf,pi433";
reg = <0>; /* CE 0 */
#address-cells = <1>;
#size-cells = <0>;
spi-max-frequency = <10000000>;
pinctrl-0 = <&pi433_pins>;
DIO0-gpio = <&gpio 24 0>;
DIO1-gpio = <&gpio 25 0>;
DIO2-gpio = <&gpio 7 0>;
status = "okay";
};
};
Then loading spi_bcm2835 and pi433 modules:
modprobe spi_bcm2835
modprobe pi433
Is this the right usage to send some data over the air?
echo 1 > /dev/pi433
[ 31.223963] spi-bcm2835 20204000.spi: registered master spi0
[ 31.224300] spi spi0.0: setup mode 0, 8 bits/w, 10000000 Hz max --> 0
[ 31.224625] spi-bcm2835 20204000.spi: registered child spi0.0
[ 31.224687] spi spi0.1: setup mode 0, 8 bits/w, 125000000 Hz max --> 0
[ 31.224977] spi-bcm2835 20204000.spi: registered child spi0.1
[ 34.062430] random: crng init done
[ 43.122779] pi433: module is from the staging directory, the quality is
unknown, you have been warned.
[ 43.143436] pi433 spi0.0: setup mode 0, 8 bits/w, 10000000 Hz max --> 0
[ 43.143465] pi433 spi0.0: spi interface setup: mode 0x 0, 8 bits per word,
10000000hz max speed
[ 43.143587] pi433 spi0.0: found pi433 (ver. 0x24)
[ 43.144027] pi433 spi0.0: DIO0 succesfully configured
[ 43.144259] pi433 spi0.0: DIO1 succesfully configured
[ 43.144274] pi433 spi0.0: set: mode
[ 43.144387] pi433 spi0.0: read 0x4 from reg 0x1
[ 43.144463] pi433 spi0.0: wrote 0x4 to reg 0x1
[ 43.144476] pi433 spi0.0: set: data mode
[ 43.144548] pi433 spi0.0: read 0x8 from reg 0x2
[ 43.144617] pi433 spi0.0: wrote 0x8 to reg 0x2
[ 43.144632] pi433 spi0.0: set: amp #0
[ 43.144703] pi433 spi0.0: read 0x9f from reg 0x11
[ 43.144772] pi433 spi0.0: wrote 0x9f to reg 0x11
[ 43.144785] pi433 spi0.0: set: amp #1
[ 43.144856] pi433 spi0.0: read 0x9f from reg 0x11
[ 43.144923] pi433 spi0.0: wrote 0x9f to reg 0x11
[ 43.144936] pi433 spi0.0: set: amp #2
[ 43.145007] pi433 spi0.0: read 0x9f from reg 0x11
[ 43.145074] pi433 spi0.0: wrote 0x9f to reg 0x11
[ 43.145088] pi433 spi0.0: set: power level
[ 43.145158] pi433 spi0.0: read 0x9f from reg 0x11
[ 43.145225] pi433 spi0.0: wrote 0x9f to reg 0x11
[ 43.145237] pi433 spi0.0: set: antenna impedance
[ 43.145308] pi433 spi0.0: read 0x8 from reg 0x18
[ 43.145376] pi433 spi0.0: wrote 0x8 to reg 0x18
[ 43.145935] pi433 pi433: created device for major 244, minor 0
[ 43.148742] pi433 pi433: thread: going to wait for new messages
Now I got hundreds messages of kind:
[ 64.221295] pi433 pi433: write: generated new msg with 2 bytes.
snip
[ 64.222671] pi433 pi433: write: generated new msg with 2 bytes.
[ 64.223882] pi433 pi433: read 2 message byte(s) from fifo queue.
[ 64.223919] pi433 spi0.0: set: mode
[ 64.224010] pi433 spi0.0: read 0x4 from reg 0x1
[ 64.224053] pi433 spi0.0: wrote 0x4 to reg 0x1
[ 64.224064] pi433 spi0.0: set: fifo threshold
[ 64.224100] pi433 spi0.0: read 0xf from reg 0x3c
[ 64.224129] pi433 spi0.0: wrote 0xf to reg 0x3c
[ 64.224159] pi433 spi0.0: 0 - 0x0
[ 64.224170] pi433 spi0.0: set: payload length
[ 64.224197] pi433 spi0.0: wrote 0x0 to reg 0x38
[ 64.224209] pi433 spi0.0: set: frequency
[ 64.224237] pi433 spi0.0: wrote 0x0 to reg 0x7
[ 64.224263] pi433 spi0.0: wrote 0x0 to reg 0x8
[ 64.224292] pi433 spi0.0: wrote 0x0 to reg 0x9
[ 64.224303] pi433 spi0.0: set: bit rate
[ 64.224331] pi433 spi0.0: wrote 0x1a to reg 0x3
[ 64.224359] pi433 spi0.0: wrote 0x88 to reg 0x4
[ 64.224370] pi433 spi0.0: set: modulation
[ 64.224404] pi433 spi0.0: read 0x8 from reg 0x2
[ 64.224431] pi433 spi0.0: wrote 0x8 to reg 0x2
[ 64.224442] pi433 spi0.0: set: deviation
[ 64.224450] pi433 spi0.0: set_deviation: illegal input param
[ 64.224458] pi433 spi0.0: set: deviation
[ 64.224466] pi433 spi0.0: set_deviation: illegal input param
[ 64.224475] pi433 spi0.0: set: DIO mapping
[ 64.224506] pi433 spi0.0: read 0x0 from reg 0x25
[ 64.224537] pi433 spi0.0: wrote 0x0 to reg 0x25
[ 64.224555] pi433 spi0.0: set: DIO mapping
[ 64.224591] pi433 spi0.0: read 0x0 from reg 0x25
[ 64.224618] pi433 spi0.0: wrote 0x0 to reg 0x25
[ 64.224637] pi433 spi0.0: set: mode
[ 64.224673] pi433 spi0.0: read 0x4 from reg 0x1
[ 64.224702] pi433 spi0.0: wrote 0xc to reg 0x1
[ 64.224718] pi433 pi433: thread: wait for packet to get sent/fifo to be empty
[ 64.224728] pi433 pi433: thread: Packet sent. Set mode to stby.
[ 64.224736] pi433 spi0.0: set: mode
[ 64.224769] pi433 spi0.0: read 0x8 from reg 0x1
[ 64.224799] pi433 spi0.0: wrote 0x4 to reg 0x1
[ 64.224811] pi433 pi433: thread: going to wait for new messages
[ 64.224824] pi433 pi433: read 2 message byte(s) from fifo queue.
[ 64.224839] pi433 spi0.0: set: mode
[ 64.224875] pi433 spi0.0: read 0x4 from reg 0x1
[ 64.224904] pi433 spi0.0: wrote 0x4 to reg 0x1
[ 64.224916] pi433 spi0.0: set: fifo threshold
[ 64.224947] pi433 spi0.0: read 0xf from reg 0x3c
[ 64.224976] pi433 spi0.0: wrote 0xf to reg 0x3c
[ 64.225001] pi433 spi0.0: 0 - 0x0
[ 64.225011] pi433 spi0.0: set: payload length
[ 64.225041] pi433 spi0.0: wrote 0x0 to reg 0x38
[ 64.225052] pi433 spi0.0: set: frequency
[ 64.225078] pi433 spi0.0: wrote 0x0 to reg 0x7
[ 64.225106] pi433 spi0.0: wrote 0x0 to reg 0x8
[ 64.225133] pi433 spi0.0: wrote 0x0 to reg 0x9
[ 64.225144] pi433 spi0.0: set: bit rate
[ 64.225173] pi433 spi0.0: wrote 0x1a to reg 0x3
[ 64.225200] pi433 spi0.0: wrote 0x88 to reg 0x4
[ 64.225210] pi433 spi0.0: set: modulation
[ 64.225242] pi433 spi0.0: read 0x8 from reg 0x2
[ 64.225270] pi433 spi0.0: wrote 0x8 to reg 0x2
[ 64.225281] pi433 spi0.0: set: deviation
[ 64.225291] pi433 spi0.0: set_deviation: illegal input param
[ 64.225298] pi433 spi0.0: set: deviation
[ 64.225306] pi433 spi0.0: set_deviation: illegal input param
[ 64.225314] pi433 spi0.0: set: DIO mapping
[ 64.225347] pi433 spi0.0: read 0x0 from reg 0x25
[ 64.225376] pi433 spi0.0: wrote 0x0 to reg 0x25
[ 64.225392] pi433 spi0.0: set: DIO mapping
[ 64.225427] pi433 spi0.0: read 0x0 from reg 0x25
[ 64.225455] pi433 spi0.0: wrote 0x0 to reg 0x25
[ 64.225473] pi433 spi0.0: set: mode
[ 64.225509] pi433 spi0.0: read 0x4 from reg 0x1
[ 64.225539] pi433 spi0.0: wrote 0xc to reg 0x1
[ 64.225554] pi433 pi433: thread: wait for packet to get sent/fifo to be empty
[ 64.225563] pi433 pi433: thread: Packet sent. Set mode to stby.
[ 64.225571] pi433 spi0.0: set: mode
[ 64.225603] pi433 spi0.0: read 0x8 from reg 0x1
[ 64.225631] pi433 spi0.0: wrote 0x4 to reg 0x1
[ 64.225644] pi433 pi433: thread: going to wait for new messages
[ 64.225658] pi433 pi433: read 2 message byte(s) from fifo queue.
[ 64.225674] pi433 spi0.0: set: mode
[ 64.225708] pi433 spi0.0: read 0x4 from reg 0x1
[ 64.225737] pi433 spi0.0: wrote 0x4 to reg 0x1
[ 64.225748] pi433 spi0.0: set: fifo threshold
[ 64.225781] pi433 spi0.0: read 0xf from reg 0x3c
[ 64.225811] pi433 spi0.0: wrote 0xf to reg 0x3c
[ 64.225836] pi433 spi0.0: 0 - 0x0
[ 64.225847] pi433 spi0.0: set: payload length
[ 64.225875] pi433 spi0.0: wrote 0x0 to reg 0x38
[ 64.225884] pi433 spi0.0: set: frequency
[ 64.225912] pi433 spi0.0: wrote 0x0 to reg 0x7
[ 64.225939] pi433 spi0.0: wrote 0x0 to reg 0x8
[ 64.225965] pi433 spi0.0: wrote 0x0 to reg 0x9
[ 64.225975] pi433 spi0.0: set: bit rate
[ 64.226002] pi433 spi0.0: wrote 0x1a to reg 0x3
[ 64.226029] pi433 spi0.0: wrote 0x88 to reg 0x4
[ 64.226038] pi433 spi0.0: set: modulation
[ 64.226071] pi433 spi0.0: read 0x8 from reg 0x2
[ 64.226097] pi433 spi0.0: wrote 0x8 to reg 0x2
[ 64.226106] pi433 spi0.0: set: deviation
[ 64.226116] pi433 spi0.0: set_deviation: illegal input param
[ 64.226124] pi433 spi0.0: set: deviation
[ 64.226132] pi433 spi0.0: set_deviation: illegal input param
[ 64.226142] pi433 spi0.0: set: DIO mapping
[ 64.226173] pi433 spi0.0: read 0x0 from reg 0x25
[ 64.226202] pi433 spi0.0: wrote 0x0 to reg 0x25
[ 64.226216] pi433 spi0.0: set: DIO mapping
[ 64.226249] pi433 spi0.0: read 0x0 from reg 0x25
[ 64.226279] pi433 spi0.0: wrote 0x0 to reg 0x25
[ 64.226296] pi433 spi0.0: set: mode
[ 64.226332] pi433 spi0.0: read 0x4 from reg 0x1
[ 64.226359] pi433 spi0.0: wrote 0xc to reg 0x1
[ 64.226372] pi433 pi433: thread: wait for packet to get sent/fifo to be empty
[ 64.226383] pi433 pi433: thread: Packet sent. Set mode to stby.
[ 64.226392] pi433 spi0.0: set: mode
[ 64.226423] pi433 spi0.0: read 0x8 from reg 0x1
[ 64.226451] pi433 spi0.0: wrote 0x4 to reg 0x1
[ 64.226463] pi433 pi433: thread: going to wait for new messages
[ 64.226475] pi433 pi433: read 2 message byte(s) from fifo queue.
[ 64.226490] pi433 spi0.0: set: mode
[ 64.226528] pi433 spi0.0: read 0x4 from reg 0x1
[ 64.226557] pi433 spi0.0: wrote 0x4 to reg 0x1
[ 64.226569] pi433 spi0.0: set: fifo threshold
[ 64.226601] pi433 spi0.0: read 0xf from reg 0x3c
[ 64.226630] pi433 spi0.0: wrote 0xf to reg 0x3c
[ 64.226658] pi433 spi0.0: 0 - 0x0
[ 64.226668] pi433 spi0.0: set: payload length
[ 64.226696] pi433 spi0.0: wrote 0x0 to reg 0x38
[ 64.226706] pi433 spi0.0: set: frequency
[ 64.226732] pi433 spi0.0: wrote 0x0 to reg 0x7
[ 64.226760] pi433 spi0.0: wrote 0x0 to reg 0x8
[ 64.226787] pi433 spi0.0: wrote 0x0 to reg 0x9
[ 64.226797] pi433 spi0.0: set: bit rate
[ 64.226825] pi433 spi0.0: wrote 0x1a to reg 0x3
[ 64.226851] pi433 spi0.0: wrote 0x88 to reg 0x4
[ 64.226861] pi433 spi0.0: set: modulation
[ 64.226893] pi433 spi0.0: read 0x8 from reg 0x2
[ 64.226921] pi433 spi0.0: wrote 0x8 to reg 0x2
[ 64.226931] pi433 spi0.0: set: deviation
[ 64.226939] pi433 spi0.0: set_deviation: illegal input param
[ 64.226948] pi433 spi0.0: set: deviation
[ 64.226956] pi433 spi0.0: set_deviation: illegal input param
[ 64.226964] pi433 spi0.0: set: DIO mapping
[ 64.226995] pi433 spi0.0: read 0x0 from reg 0x25
[ 64.227026] pi433 spi0.0: wrote 0x0 to reg 0x25
[ 64.227040] pi433 spi0.0: set: DIO mapping
[ 64.227074] pi433 spi0.0: read 0x0 from reg 0x25
[ 64.227101] pi433 spi0.0: wrote 0x0 to reg 0x25
[ 64.227117] pi433 spi0.0: set: mode
[ 64.227154] pi433 spi0.0: read 0x4 from reg 0x1
[ 64.227183] pi433 spi0.0: wrote 0xc to reg 0x1
[ 64.227197] pi433 pi433: thread: wait for packet to get sent/fifo to be empty
[ 64.227206] pi433 pi433: thread: Packet sent. Set mode to stby.
[ 64.227214] pi433 spi0.0: set: mode
[ 64.227245] pi433 spi0.0: read 0x8 from reg 0x1
[ 64.227275] pi433 spi0.0: wrote 0x4 to reg 0x1
[ 64.227286] pi433 pi433: thread: going to wait for new messages
[ 64.227300] pi433 pi433: read 2 message byte(s) from fifo queue.
[ 64.227315] pi433 spi0.0: set: mode
[ 64.227350] pi433 spi0.0: read 0x4 from reg 0x1
[ 64.227379] pi433 spi0.0: wrote 0x4 to reg 0x1
[ 64.227392] pi433 spi0.0: set: fifo threshold
[ 64.227425] pi433 spi0.0: read 0xf from reg 0x3c
[ 64.227454] pi433 spi0.0: wrote 0xf to reg 0x3c
[ 64.227480] pi433 spi0.0: 0 - 0x0
[ 64.227491] pi433 spi0.0: set: payload length
[ 64.227520] pi433 spi0.0: wrote 0x0 to reg 0x38
[ 64.227531] pi433 spi0.0: set: frequency
[ 64.227557] pi433 spi0.0: wrote 0x0 to reg 0x7
[ 64.227586] pi433 spi0.0: wrote 0x0 to reg 0x8
[ 64.227611] pi433 spi0.0: wrote 0x0 to reg 0x9
[ 64.227621] pi433 spi0.0: set: bit rate
[ 64.227714] pi433 spi0.0: wrote 0x1a to reg 0x3
[ 64.227750] pi433 spi0.0: wrote 0x88 to reg 0x4
[ 64.227761] pi433 spi0.0: set: modulation
[ 64.227843] pi433 spi0.0: read 0x8 from reg 0x2
[ 64.227875] pi433 spi0.0: wrote 0x8 to reg 0x2
[ 64.227885] pi433 spi0.0: set: deviation
[ 64.227896] pi433 spi0.0: set_deviation: illegal input param
[ 64.227904] pi433 spi0.0: set: deviation
[ 64.227912] pi433 spi0.0: set_deviation: illegal input param
[ 64.227920] pi433 spi0.0: set: DIO mapping
[ 64.227953] pi433 spi0.0: read 0x0 from reg 0x25
[ 64.227983] pi433 spi0.0: wrote 0x0 to reg 0x25
[ 64.227998] pi433 spi0.0: set: DIO mapping
[ 64.228035] pi433 spi0.0: read 0x0 from reg 0x25
[ 64.228063] pi433 spi0.0: wrote 0x0 to reg 0x25
[ 64.228080] pi433 spi0.0: set: mode
[ 64.228116] pi433 spi0.0: read 0x4 from reg 0x1
[ 64.228146] pi433 spi0.0: wrote 0xc to reg 0x1
[ 64.228161] pi433 pi433: thread: wait for packet to get sent/fifo to be empty
[ 64.228171] pi433 pi433: thread: Packet sent. Set mode to stby.
[ 64.228179] pi433 spi0.0: set: mode
[ 64.228210] pi433 spi0.0: read 0x8 from reg 0x1
[ 64.228238] pi433 spi0.0: wrote 0x4 to reg 0x1
[ 64.228250] pi433 pi433: thread: going to wait for new messages
[ 64.228263] pi433 pi433: read 2 message byte(s) from fifo queue.
[ 64.228282] pi433 spi0.0: set: mode
[ 64.228317] pi433 spi0.0: read 0x4 from reg 0x1
[ 64.228347] pi433 spi0.0: wrote 0x4 to reg 0x1
[ 64.228357] pi433 spi0.0: set: fifo threshold
[ 64.228387] pi433 spi0.0: read 0xf from reg 0x3c
[ 64.228417] pi433 spi0.0: wrote 0xf to reg 0x3c
[ 64.228443] pi433 spi0.0: 0 - 0x0
[ 64.228453] pi433 spi0.0: set: payload length
[ 64.228479] pi433 spi0.0: wrote 0x0 to reg 0x38
[ 64.228489] pi433 spi0.0: set: frequency
[ 64.228517] pi433 spi0.0: wrote 0x0 to reg 0x7
[ 64.228544] pi433 spi0.0: wrote 0x0 to reg 0x8
[ 64.228571] pi433 spi0.0: wrote 0x0 to reg 0x9
[ 64.228581] pi433 spi0.0: set: bit rate
[ 64.228609] pi433 spi0.0: wrote 0x1a to reg 0x3
[ 64.228636] pi433 spi0.0: wrote 0x88 to reg 0x4
[ 64.228648] pi433 spi0.0: set: modulation
[ 64.228682] pi433 spi0.0: read 0x8 from reg 0x2
[ 64.228709] pi433 spi0.0: wrote 0x8 to reg 0x2
[ 64.228720] pi433 spi0.0: set: deviation
[ 64.228730] pi433 spi0.0: set_deviation: illegal input param
[ 64.228738] pi433 spi0.0: set: deviation
[ 64.228746] pi433 spi0.0: set_deviation: illegal input param
[ 64.228754] pi433 spi0.0: set: DIO mapping
[ 64.228787] pi433 spi0.0: read 0x0 from reg 0x25
[ 64.228814] pi433 spi0.0: wrote 0x0 to reg 0x25
[ 64.228829] pi433 spi0.0: set: DIO mapping
[ 64.228863] pi433 spi0.0: read 0x0 from reg 0x25
[ 64.228891] pi433 spi0.0: wrote 0x0 to reg 0x25
[ 64.228908] pi433 spi0.0: set: mode
[ 64.228943] pi433 spi0.0: read 0x4 from reg 0x1
[ 64.228971] pi433 spi0.0: wrote 0xc to reg 0x1
[ 64.228985] pi433 pi433: thread: wait for packet to get sent/fifo to be empty
[ 64.228995] pi433 pi433: thread: Packet sent. Set mode to stby.
[ 64.229003] pi433 spi0.0: set: mode
[ 64.229036] pi433 spi0.0: read 0x8 from reg 0x1
[ 64.229064] pi433 spi0.0: wrote 0x4 to reg 0x1
[ 64.229075] pi433 pi433: thread: going to wait for new messages
[ 64.229089] pi433 pi433: read 2 message byte(s) from fifo queue.
[ 64.229106] pi433 spi0.0: set: mode
[ 64.229141] pi433 spi0.0: read 0x4 from reg 0x1
[ 64.229171] pi433 spi0.0: wrote 0x4 to reg 0x1
[ 64.229182] pi433 spi0.0: set: fifo threshold
[ 64.229214] pi433 spi0.0: read 0xf from reg 0x3c
[ 64.229243] pi433 spi0.0: wrote 0xf to reg 0x3c
[ 64.229271] pi433 spi0.0: 0 - 0x0
[ 64.229281] pi433 spi0.0: set: payload length
[ 64.229309] pi433 spi0.0: wrote 0x0 to reg 0x38
[ 64.229319] pi433 spi0.0: set: frequency
[ 64.229345] pi433 spi0.0: wrote 0x0 to reg 0x7
[ 64.229374] pi433 spi0.0: wrote 0x0 to reg 0x8
[ 64.229401] pi433 spi0.0: wrote 0x0 to reg 0x9
[ 64.229412] pi433 spi0.0: set: bit rate
[ 64.229440] pi433 spi0.0: wrote 0x1a to reg 0x3
[ 64.229467] pi433 spi0.0: wrote 0x88 to reg 0x4
[ 64.229477] pi433 spi0.0: set: modulation
[ 64.229510] pi433 spi0.0: read 0x8 from reg 0x2
[ 64.229539] pi433 spi0.0: wrote 0x8 to reg 0x2
[ 64.229550] pi433 spi0.0: set: deviation
[ 64.229558] pi433 spi0.0: set_deviation: illegal input param
[ 64.229566] pi433 spi0.0: set: deviation
[ 64.229574] pi433 spi0.0: set_deviation: illegal input param
[ 64.229582] pi433 spi0.0: set: DIO mapping
[ 64.229615] pi433 spi0.0: read 0x0 from reg 0x25
[ 64.229645] pi433 spi0.0: wrote 0x0 to reg 0x25
[ 64.229659] pi433 spi0.0: set: DIO mapping
[ 64.229694] pi433 spi0.0: read 0x0 from reg 0x25
[ 64.229721] pi433 spi0.0: wrote 0x0 to reg 0x25
[ 64.229739] pi433 spi0.0: set: mode
[ 64.229775] pi433 spi0.0: read 0x4 from reg 0x1
[ 64.229805] pi433 spi0.0: wrote 0xc to reg 0x1
[ 64.229817] pi433 pi433: thread: wait for packet to get sent/fifo to be empty
[ 64.229828] pi433 pi433: thread: Packet sent. Set mode to stby.
[ 64.229836] pi433 spi0.0: set: mode
[ 64.229869] pi433 spi0.0: read 0x8 from reg 0x1
[ 64.229897] pi433 spi0.0: wrote 0x4 to reg 0x1
[ 64.229909] pi433 pi433: thread: going to wait for new messages
[ 64.229922] pi433 pi433: read 2 message byte(s) from fifo queue.
[ 64.229939] pi433 spi0.0: set: mode
[ 64.229973] pi433 spi0.0: read 0x4 from reg 0x1
[ 64.230002] pi433 spi0.0: wrote 0x4 to reg 0x1
[ 64.230013] pi433 spi0.0: set: fifo threshold
[ 64.230045] pi433 spi0.0: read 0xf from reg 0x3c
[ 64.230074] pi433 spi0.0: wrote 0xf to reg 0x3c
[ 64.230099] pi433 spi0.0: 0 - 0x0
[ 64.230109] pi433 spi0.0: set: payload length
[ 64.230137] pi433 spi0.0: wrote 0x0 to reg 0x38
[ 64.230148] pi433 spi0.0: set: frequency
[ 64.230175] pi433 spi0.0: wrote 0x0 to reg 0x7
[ 64.230203] pi433 spi0.0: wrote 0x0 to reg 0x8
[ 64.230227] pi433 spi0.0: wrote 0x0 to reg 0x9
[ 64.230237] pi433 spi0.0: set: bit rate
[ 64.230266] pi433 spi0.0: wrote 0x1a to reg 0x3
[ 64.230293] pi433 spi0.0: wrote 0x88 to reg 0x4
[ 64.230303] pi433 spi0.0: set: modulation
[ 64.230336] pi433 spi0.0: read 0x8 from reg 0x2
[ 64.230362] pi433 spi0.0: wrote 0x8 to reg 0x2
[ 64.230375] pi433 spi0.0: set: deviation
[ 64.230383] pi433 spi0.0: set_deviation: illegal input param
[ 64.230392] pi433 spi0.0: set: deviation
[ 64.230401] pi433 spi0.0: set_deviation: illegal input param
[ 64.230409] pi433 spi0.0: set: DIO mapping
[ 64.230442] pi433 spi0.0: read 0x0 from reg 0x25
[ 64.230469] pi433 spi0.0: wrote 0x0 to reg 0x25
[ 64.230484] pi433 spi0.0: set: DIO mapping
[ 64.230520] pi433 spi0.0: read 0x0 from reg 0x25
[ 64.230547] pi433 spi0.0: wrote 0x0 to reg 0x25
[ 64.230565] pi433 spi0.0: set: mode
[ 64.230600] pi433 spi0.0: read 0x4 from reg 0x1
[ 64.230629] pi433 spi0.0: wrote 0xc to reg 0x1
[ 64.230643] pi433 pi433: thread: wait for packet to get sent/fifo to be empty
[ 64.230654] pi433 pi433: thread: Packet sent. Set mode to stby.
[ 64.230662] pi433 spi0.0: set: mode
[ 64.230695] pi433 spi0.0: read 0x8 from reg 0x1
[ 64.230722] pi433 spi0.0: wrote 0x4 to reg 0x1
[ 64.230733] pi433 pi433: thread: going to wait for new messages
[ 64.230746] pi433 pi433: read 2 message byte(s) from fifo queue.
[ 64.230762] pi433 spi0.0: set: mode
[ 64.230799] pi433 spi0.0: read 0x4 from reg 0x1
[ 64.230830] pi433 spi0.0: wrote 0x4 to reg 0x1
[ 64.230839] pi433 spi0.0: set: fifo threshold
[ 64.230871] pi433 spi0.0: read 0xf from reg 0x3c
[ 64.230901] pi433 spi0.0: wrote 0xf to reg 0x3c
[ 64.230928] pi433 spi0.0: 0 - 0x0
[ 64.230939] pi433 spi0.0: set: payload length
[ 64.230967] pi433 spi0.0: wrote 0x0 to reg 0x38
[ 64.230977] pi433 spi0.0: set: frequency
[ 64.231003] pi433 spi0.0: wrote 0x0 to reg 0x7
[ 64.231033] pi433 spi0.0: wrote 0x0 to reg 0x8
[ 64.231059] pi433 spi0.0: wrote 0x0 to reg 0x9
[ 64.231070] pi433 spi0.0: set: bit rate
[ 64.231098] pi433 spi0.0: wrote 0x1a to reg 0x3
[ 64.231125] pi433 spi0.0: wrote 0x88 to reg 0x4
[ 64.231136] pi433 spi0.0: set: modulation
[ 64.231169] pi433 spi0.0: read 0x8 from reg 0x2
[ 64.231196] pi433 spi0.0: wrote 0x8 to reg 0x2
[ 64.231207] pi433 spi0.0: set: deviation
[ 64.231216] pi433 spi0.0: set_deviation: illegal input param
[ 64.231223] pi433 spi0.0: set: deviation
[ 64.231231] pi433 spi0.0: set_deviation: illegal input param
[ 64.231239] pi433 spi0.0: set: DIO mapping
[ 64.231273] pi433 spi0.0: read 0x0 from reg 0x25
[ 64.231300] pi433 spi0.0: wrote 0x0 to reg 0x25
[ 64.231315] pi433 spi0.0: set: DIO mapping
[ 64.231350] pi433 spi0.0: read 0x0 from reg 0x25
[ 64.231378] pi433 spi0.0: wrote 0x0 to reg 0x25
[ 64.231397] pi433 spi0.0: set: mode
[ 64.231432] pi433 spi0.0: read 0x4 from reg 0x1
[ 64.231462] pi433 spi0.0: wrote 0xc to reg 0x1
[ 64.231475] pi433 pi433: thread: wait for packet to get sent/fifo to be empty
[ 64.231485] pi433 pi433: thread: Packet sent. Set mode to stby.
[ 64.231493] pi433 spi0.0: set: mode
[ 64.231529] pi433 spi0.0: read 0x8 from reg 0x1
[ 64.231555] pi433 spi0.0: wrote 0x4 to reg 0x1
[ 64.231567] pi433 pi433: thread: going to wait for new messages
[ 64.231582] pi433 pi433: read 2 message byte(s) from fifo queue.
[ 64.231597] pi433 spi0.0: set: mode
[ 64.231632] pi433 spi0.0: read 0x4 from reg 0x1
[ 64.231663] pi433 spi0.0: wrote 0x4 to reg 0x1
[ 64.231673] pi433 spi0.0: set: fifo threshold
[ 64.231704] pi433 spi0.0: read 0xf from reg 0x3c
[ 64.231733] pi433 spi0.0: wrote 0xf to reg 0x3c
[ 64.231759] pi433 spi0.0: 0 - 0x0
[ 64.231773] pi433 spi0.0: set: payload length
[ 64.231799] pi433 spi0.0: wrote 0x0 to reg 0x38
[ 64.231809] pi433 spi0.0: set: frequency
[ 64.231837] pi433 spi0.0: wrote 0x0 to reg 0x7
[ 64.231864] pi433 spi0.0: wrote 0x0 to reg 0x8
[ 64.231890] pi433 spi0.0: wrote 0x0 to reg 0x9
[ 64.231900] pi433 spi0.0: set: bit rate
[ 64.231927] pi433 spi0.0: wrote 0x1a to reg 0x3
[ 64.231954] pi433 spi0.0: wrote 0x88 to reg 0x4
[ 64.231965] pi433 spi0.0: set: modulation
[ 64.231995] pi433 spi0.0: read 0x8 from reg 0x2
[ 64.232023] pi433 spi0.0: wrote 0x8 to reg 0x2
[ 64.232035] pi433 spi0.0: set: deviation
[ 64.232044] pi433 spi0.0: set_deviation: illegal input param
[ 64.232051] pi433 spi0.0: set: deviation
[ 64.232059] pi433 spi0.0: set_deviation: illegal input param
[ 64.232068] pi433 spi0.0: set: DIO mapping
[ 64.232101] pi433 spi0.0: read 0x0 from reg 0x25
[ 64.232127] pi433 spi0.0: wrote 0x0 to reg 0x25
[ 64.232143] pi433 spi0.0: set: DIO mapping
[ 64.232178] pi433 spi0.0: read 0x0 from reg 0x25
[ 64.232206] pi433 spi0.0: wrote 0x0 to reg 0x25
[ 64.232224] pi433 spi0.0: set: mode
[ 64.232258] pi433 spi0.0: read 0x4 from reg 0x1
[ 64.232287] pi433 spi0.0: wrote 0xc to reg 0x1
[ 64.232300] pi433 pi433: thread: wait for packet to get sent/fifo to be empty
[ 64.232310] pi433 pi433: thread: Packet sent. Set mode to stby.
[ 64.232318] pi433 spi0.0: set: mode
[ 64.232351] pi433 spi0.0: read 0x8 from reg 0x1
[ 64.232378] pi433 spi0.0: wrote 0x4 to reg 0x1
[ 64.232390] pi433 pi433: thread: going to wait for new messages
[ 64.232404] pi433 pi433: read 2 message byte(s) from fifo queue.
[ 64.232421] pi433 spi0.0: set: mode
[ 64.232456] pi433 spi0.0: read 0x4 from reg 0x1
[ 64.232485] pi433 spi0.0: wrote 0x4 to reg 0x1
[ 64.232495] pi433 spi0.0: set: fifo threshold
[ 64.232528] pi433 spi0.0: read 0xf from reg 0x3c
[ 64.232557] pi433 spi0.0: wrote 0xf to reg 0x3c
[ 64.235171] pi433 pi433: write: generated new msg with 2 bytes.
Now I got again hundreds messages of kind:
[ 64.235198] pi433 pi433: write: generated new msg with 2 bytes.
snip
[ 64.250836] pi433 spi0.0: 0 - 0x0
[ 64.250859] pi433 spi0.0: set: payload length
[ 64.250938] pi433 spi0.0: wrote 0x0 to reg 0x38
[ 64.250951] pi433 spi0.0: set: frequency
[ 64.251019] pi433 spi0.0: wrote 0x0 to reg 0x7
[ 64.251086] pi433 spi0.0: wrote 0x0 to reg 0x8
[ 64.251153] pi433 spi0.0: wrote 0x0 to reg 0x9
[ 64.251168] pi433 spi0.0: set: bit rate
[ 64.251233] pi433 spi0.0: wrote 0x1a to reg 0x3
[ 64.251299] pi433 spi0.0: wrote 0x88 to reg 0x4
[ 64.251312] pi433 spi0.0: set: modulation
[ 64.251383] pi433 spi0.0: read 0x8 from reg 0x2
[ 64.251449] pi433 spi0.0: wrote 0x8 to reg 0x2
[ 64.251461] pi433 spi0.0: set: deviation
[ 64.251471] pi433 spi0.0: set_deviation: illegal input param
[ 64.251479] pi433 spi0.0: set: deviation
[ 64.251487] pi433 spi0.0: set_deviation: illegal input param
[ 64.251497] pi433 spi0.0: set: DIO mapping
[ 64.251567] pi433 spi0.0: read 0x0 from reg 0x25
[ 64.251631] pi433 spi0.0: wrote 0x0 to reg 0x25
[ 64.251709] pi433 spi0.0: set: DIO mapping
[ 64.251836] pi433 spi0.0: read 0x0 from reg 0x25
[ 64.251911] pi433 spi0.0: wrote 0x0 to reg 0x25
[ 64.251936] pi433 spi0.0: set: mode
[ 64.252008] pi433 spi0.0: read 0x4 from reg 0x1
Now I got again hundreds messages of kind:
[ 64.252112] pi433 pi433: write: generated new msg with 2 bytes.
snip
[ 64.255690] pi433 pi433: write to fifo failed: 0x0
[ 64.256575] pi433 spi0.0: wrote 0xc to reg 0x1
[ 64.256600] pi433 pi433: thread: wait for packet to get sent/fifo to be empty
[ 64.256613] pi433 pi433: thread: Packet sent. Set mode to stby.
[ 64.256623] pi433 spi0.0: set: mode
[ 64.258122] pi433 spi0.0: read 0x8 from reg 0x1
[ 64.258235] pi433 spi0.0: wrote 0x4 to reg 0x1
[ 64.258257] pi433 pi433: thread: going to wait for new messages
Best regards,
Oliver
Hi Oliver,
thanks for testing with real hardware :-)
In my product, I use Raspbian. Therefore, I work with a kernel from
Raspbian. Raspbian supports device tree overlays.
So I don't use dtparam=spi=on, but dtoverlay=pi433.
I don't modify the bcm2835-rpi-b-rev2.dts, but use the
pi433-overlay.dts, provided in the driver documentation.
I am not sure, whether you need to load spi_bcm2835. I never did that,
but maybe it is done implicitly on my system.
Never adressed Pi433 from command line, but always used a program to do so.
Anyway: The way you did it, you missed to setup the tx and/or rx
configuration. I am not sure, whether there are useful defaults in the
current version of the driver, allowing you can start with tx right from
the start. Most probably all entries are preset with zero, that might
lead to an not really perfect configuration of the chip. So you need to
use the ioctl first, to set usefull config params.
I don't know, what generates the hundrets of "write: generated new msg
with 2 bytes.".
This message is shown up, as soon as you ask the driver to send
something. There is an internal (SW) queue, where tx jobs get stored.
The message tells you, that a telegram with 2 bytes was stored in this
queue. I guess the two bytes are the '1' and a new line, generated by
the echo. The repetition of the message is quite strange.
Maybe due to misssing configuration / bad default settings.
As soon, as there is something in the queue, the driver should leave RX
mode (where he was waiting for messages in the air) and start to
transfer the messages from the queue with the given (or in your case
missing) configuration for TX. As soon as the queue is empty, the driver
should reconfigure for RX and restart listening on the air.
Unfortunally I can't find the source code from my testprogram, that is
compatible with the current version of the driver. Hope I didn't format
the wrong SD-card.
Just found sources for the "old" version of the driver, that was
intended to support more then just Pi433...
Will provide the source as soon as I find it.
At the moment, I just can provide a binary, if it helps...
Hope this helps understanding,
regards,
Marcus
_______________________________________________
devel mailing list
de...@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
