On Thu, 13 Dec 2018 14:46:23 +0200
Stefan Popa <stefan.p...@analog.com> wrote:
> Document support for AD7606 Analog to Digital Converter.
>
> Signed-off-by: Stefan Popa <stefan.p...@analog.com>
> Reviewed-by: Rob Herring <r...@kernel.org>
Will have to wait on this as the MAINTAINERS bit obviously isn't there yet.
Otherwise I would have just added it now. Oh well, v2.
Thanks,
Jonathan
> ---
> .../devicetree/bindings/iio/adc/adi,ad7606.txt | 65
> ++++++++++++++++++++++
> MAINTAINERS | 1 +
> 2 files changed, 66 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
>
> diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
> b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
> new file mode 100644
> index 0000000..d7b6241
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
> @@ -0,0 +1,65 @@
> +Analog Devices AD7606 Simultaneous Sampling ADC
> +
> +Required properties for the AD7606:
> +
> +- compatible: Must be one of
> + * "adi,ad7605-4"
> + * "adi,ad7606-8"
> + * "adi,ad7606-6"
> + * "adi,ad7606-4"
> +- reg: SPI chip select number for the device
> +- spi-max-frequency: Max SPI frequency to use
> + see: Documentation/devicetree/bindings/spi/spi-bus.txt
> +- spi-cpha: See Documentation/devicetree/bindings/spi/spi-bus.txt
> +- avcc-supply: phandle to the Avcc power supply
> +- interrupts: IRQ line for the ADC
> + see:
> Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
> +- adi,conversion-start-gpios: must be the device tree identifier of the
> CONVST pin.
> + This logic input is used to initiate conversions on the analog
> + input channels. As the line is active high, it should be
> marked
> + GPIO_ACTIVE_HIGH.
> +
> +Optional properties:
> +
> +- reset-gpios: must be the device tree identifier of the RESET pin. If
> specified,
> + it will be asserted during driver probe. As the line is active
> high,
> + it should be marked GPIO_ACTIVE_HIGH.
> +- standby-gpios: must be the device tree identifier of the STBY pin. This
> pin is used
> + to place the AD7606 into one of two power-down modes, Standby
> mode or
> + Shutdown mode. As the line is active low, it should be marked
> + GPIO_ACTIVE_LOW.
> +- adi,first-data-gpios: must be the device tree identifier of the FRSTDATA
> pin.
> + The FRSTDATA output indicates when the first channel, V1, is
> + being read back on either the parallel, byte or serial
> interface.
> + As the line is active high, it should be marked
> GPIO_ACTIVE_HIGH.
> +- adi,range-gpios: must be the device tree identifier of the RANGE pin. The
> polarity on
> + this pin determines the input range of the analog input channels.
> If
> + this pin is tied to a logic high, the analog input range is ±10V
> for
> + all channels. If this pin is tied to a logic low, the analog
> input range
> + is ±5V for all channels. As the line is active high, it should be
> marked
> + GPIO_ACTIVE_HIGH.
> +- adi,oversampling-ratio-gpios: must be the device tree identifier of the
> over-sampling
> + mode pins. As the line is active high, it
> should be marked
> + GPIO_ACTIVE_HIGH.
> +
> +Example:
> +
> + adc@0 {
> + compatible = "adi,ad7606-8";
> + reg = <0>;
> + spi-max-frequency = <1000000>;
> + spi-cpol;
> +
> + avcc-supply = <&adc_vref>;
> +
> + interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-parent = <&gpio>;
> +
> + adi,conversion-start-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
> + reset-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>;
> + adi,first-data-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
> + adi,oversampling-ratio-gpios = <&gpio 18 GPIO_ACTIVE_HIGH
> + &gpio 23 GPIO_ACTIVE_HIGH
> + &gpio 26 GPIO_ACTIVE_HIGH>;
> + standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
> + };
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 7256ce6..798e9a2 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -859,6 +859,7 @@ L: linux-...@vger.kernel.org
> W: http://ez.analog.com/community/linux-device-drivers
> S: Supported
> F: drivers/iio/adc/ad7606.c
> +F: Documentation/devicetree/bindings/iio/adc/ad7606.txt
>
> ANALOG DEVICES INC AD9389B DRIVER
> M: Hans Verkuil <hans.verk...@cisco.com>
_______________________________________________
devel mailing list
de...@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
