I found that the comments had several typos such as "aenable", "internaly" and 
some others.
I fixed them all.

Signed-off-by: Laura Lazzati <laura.lazzati...@gmail.com>
---
 drivers/staging/octeon-usb/octeon-hcd.h | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/drivers/staging/octeon-usb/octeon-hcd.h 
b/drivers/staging/octeon-usb/octeon-hcd.h
index 769c36cf6614..9ed619c93a4e 100644
--- a/drivers/staging/octeon-usb/octeon-hcd.h
+++ b/drivers/staging/octeon-usb/octeon-hcd.h
@@ -1711,7 +1711,7 @@ union cvmx_usbnx_usbp_ctl_status {
         *      Indicates an internal error was detected during
         *      the BIST sequence.
         * @tdata_out: PHY Test Data Out.
-        *      Presents either internaly generated signals or
+        *      Presents either internally generated signals or
         *      test register contents, based upon the value of
         *      test_data_out_sel.
         * @siddq: Drives the USBP (USB-PHY) SIDDQ input.
@@ -1737,7 +1737,7 @@ union cvmx_usbnx_usbp_ctl_status {
         *      to D+. When an A/B device is acting as a host
         *      (downstream-facing port), dp_pulldown and
         *      dm_pulldown are enabled. This must not toggle
-        *      during normal opeartion.
+        *      during normal operation.
         * @dm_pulld: PHY DM_PULLDOWN input to the USB-PHY.
         *      This signal enables the pull-down resistance on
         *      the D- line. '1' pull down-resistance is connected
@@ -1745,7 +1745,7 @@ union cvmx_usbnx_usbp_ctl_status {
         *      to D-. When an A/B device is acting as a host
         *      (downstream-facing port), dp_pulldown and
         *      dm_pulldown are enabled. This must not toggle
-        *      during normal opeartion.
+        *      during normal operation.
         * @hst_mode: When '0' the USB is acting as HOST, when '1'
         *      USB is acting as device. This field needs to be
         *      set while the USB is in reset.
@@ -1784,7 +1784,7 @@ union cvmx_usbnx_usbp_ctl_status {
         *      Used to activate BIST in the PHY.
         * @tdata_sel: Test Data Out Select.
         *      '1' test_data_out[3:0] (PHY) register contents
-        *      are output. '0' internaly generated signals are
+        *      are output. '0' internally generated signals are
         *      output.
         * @taddr_in: Mode Address for Test Interface.
         *      Specifies the register address for writing to or
@@ -1797,7 +1797,7 @@ union cvmx_usbnx_usbp_ctl_status {
         *      This is a test signal. When the USB Core is
         *      powered up (not in Susned Mode), an automatic
         *      tester can use this to disable phy_clock and
-        *      free_clk, then re-eanable them with an aligned
+        *      free_clk, then re-enable them with an aligned
         *      phase.
         *      '1': The phy_clk and free_clk outputs are
         *      disabled. "0": The phy_clock and free_clk outputs
-- 
2.17.1

_______________________________________________
devel mailing list
de...@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel

Reply via email to