Not sure if all variants of the Salvator board have the HDMI decoder
chip (the ADV7482) connected to the SSI4 on R-Car SoC, as it is on
Salvator-X ES1, so the the ADV7482 endpoint and connection definitions
are placed in the board file.
I do assume though that all Salvator variants have the CLK_C clock line
hard-wired to the ADV7482 HDMI decoder, and remove it from the list of
clocks provided by the R-Car sound system.
The I2C wiring is also likely to persist across the variants (similar
to ak4613, connected to the same interface), so that is in the common
file.
Signed-off-by: Alexander Riesen <alexander.rie...@cetitec.com>
---
.../dts/renesas/r8a7795-es1-salvator-x.dts | 24 ++++++++++++-
.../boot/dts/renesas/salvator-common.dtsi | 35 ++++++++++++++++---
2 files changed, 53 insertions(+), 6 deletions(-)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dts
b/arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dts
index c72968623e94..10f74f7a0efe 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dts
@@ -136,9 +136,29 @@
playback = <&ssi3>;
};
};
+ rsnd_port3: port@3 {
+ reg = <3>;
+ rsnd_endpoint3: endpoint {
+ remote-endpoint = <&adv7482_i2s>;
+
+ dai-tdm-slot-num = <8>;
+ dai-tdm-slot-width = <32>;
+ dai-format = "left_j";
+ mclk-fs = <256>;
+ bitclock-master = <&adv7482_i2s>;
+ frame-master = <&adv7482_i2s>;
+ system-clock-direction-out;
+
+ capture = <&ssi4>;
+ };
+ };
};
};
+&adv7482_i2s {
+ remote-endpoint = <&rsnd_endpoint3>;
+};
+
&sata {
status = "okay";
};
@@ -146,9 +166,11 @@
&sound_card {
dais = <&rsnd_port0 /* ak4613 */
&rsnd_port1 /* HDMI0 */
- &rsnd_port2>; /* HDMI1 */
+ &rsnd_port2 /* HDMI1 */
+ &rsnd_port3>; /* adv7482 hdmi-in */
};
+
&usb2_phy2 {
pinctrl-0 = <&usb2_pins>;
pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/renesas/salvator-common.dtsi
b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
index 21e01056e759..e887805b16fc 100644
--- a/arch/arm64/boot/dts/renesas/salvator-common.dtsi
+++ b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
@@ -322,6 +322,10 @@
clock-frequency = <22579200>;
};
+&audio_clk_c {
+ clock-frequency = <12288000>;
+};
+
&avb {
pinctrl-0 = <&avb_pins>;
pinctrl-names = "default";
@@ -471,12 +475,14 @@
#address-cells = <1>;
#size-cells = <0>;
+ #sound-dai-cells = <0>;
interrupt-parent = <&gpio6>;
interrupt-names = "intrq1", "intrq2";
interrupts = <30 IRQ_TYPE_LEVEL_LOW>,
<31 IRQ_TYPE_LEVEL_LOW>;
-
+ clocks = <&rcar_sound 3>, <&audio_clk_c>;
+ clock-names = "clk-hdmi-video", "clk-hdmi-i2s-mclk";
port@7 {
reg = <7>;
@@ -512,6 +518,14 @@
remote-endpoint = <&csi20_in>;
};
};
+
+ port@c {
+ reg = <12>;
+
+ adv7482_i2s: endpoint {
+ /* remote-endpoint defined in the board file */
+ };
+ };
};
csa_vdd: adc@7c {
@@ -686,7 +700,8 @@
};
sound_pins: sound {
- groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
+ groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a",
+ "ssi4_data";
function = "ssi";
};
@@ -735,8 +750,8 @@
pinctrl-0 = <&sound_pins &sound_clk_pins>;
pinctrl-names = "default";
- /* Single DAI */
- #sound-dai-cells = <0>;
+ /* multi DAI */
+ #sound-dai-cells = <1>;
/* audio_clkout0/1/2/3 */
#clock-cells = <1>;
@@ -760,8 +775,18 @@
<&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
<&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
<&audio_clk_a>, <&cs2000>,
- <&audio_clk_c>,
<&cpg CPG_CORE CPG_AUDIO_CLK_I>;
+ clock-names = "ssi-all",
+ "ssi.9", "ssi.8", "ssi.7", "ssi.6",
+ "ssi.5", "ssi.4", "ssi.3", "ssi.2",
+ "ssi.1", "ssi.0",
+ "src.9", "src.8", "src.7", "src.6",
+ "src.5", "src.4", "src.3", "src.2",
+ "src.1", "src.0",
+ "mix.1", "mix.0",
+ "ctu.1", "ctu.0",
+ "dvc.0", "dvc.1",
+ "clk_a", "clk_b", "clk_i";
ports {
#address-cells = <1>;
--
2.24.1.508.g91d2dafee0
_______________________________________________
devel mailing list
de...@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
