The IC-7800 CT-17 code is 6Ah. I would try that using a 756PRO series with that code and see what happens... 73, Art W6KY
--- Larry Burke <[EMAIL PROTECTED]> wrote: > > The IC-7800 is not in the pull down menu of > supported rigs in the latest > version of DX4WIN. Is there a rig in the pull-down > that is "closest to" the > 7800 and might work? > > Larry Burke WI5A > Lima, Ohio > > > _______________________________________________ > Dx4win mailing list > Dx4win@mailman.qth.net > http://mailman.qth.net/mailman/listinfo/dx4win > I refuse to join any club that would have me as a member. From [EMAIL PROTECTED] Mon Feb 6 00:16:00 2006 From: [EMAIL PROTECTED] (john paul) Date: Tue Feb 7 05:45:12 2006 Subject: [Dx4win] Problem Message-ID: <[EMAIL PROTECTED]> I just got a message when I tried to log on using my DX4WIN version 6.03. The following message came up and keeps coming up each time I try to open my logs. DX4WIN V6 Access.Violation of Address 005B3E2A in module 'DX4WIN.EXE' Read of Address FFFFFFFF When I click OK it shows this message A fatal error occurred i reading the logfile. When I click OK on that one I get the following message Unknown Version of Logfile. How do I get this reset? I am lost and can't find this in the help files. Thanks JohnPaul/AB4PP From [EMAIL PROTECTED] Tue Feb 7 08:24:19 2006 From: [EMAIL PROTECTED] (john paul) Date: Tue Feb 7 08:27:32 2006 Subject: [Dx4win] Problem Solved Message-ID: <[EMAIL PROTECTED]> Thanks to wonderful Tech Support. As usual, Steve came through and found my problem. Short phone call and he analyzed what had happened and he had seen this corrupted Config file occurrence and he talked me through getting the problem solved and I am up and running again. Now, the important part about this is that I regularly, and I repeat, REGULARLY create and keep a backup file with all my data on it. I refresh it as often as I can and this seemed to have helped me get back all the info and all I needed to do was re-add some of the QSL info and cards received since the last backup and I was back up to speed. Again, a BIG THANKS for the help and guys, the tech support is there. With other programs I have used this would have been a nightmare, and might have taken some time to even figure out. Thanks STEVE for the help. JohnPaul/AB4PP Raleigh, NC From [EMAIL PROTECTED] Tue Feb 7 16:09:07 2006 From: [EMAIL PROTECTED] (Duane A Calvin) Date: Tue Feb 7 16:14:18 2006 Subject: [Dx4win] Orion (I) FSK as Pack? Message-ID: <[EMAIL PROTECTED]> Jim, There is an edit you need to make in the rig file to change it from Pactor to FSK. I don't have the information with me here at work but I have it at home. I'll try to remember to send it to you this evening. (You can also change the CW mode chosen when pouncing on a spot from LCW to UCW.) 73, Duane On Mon, 6 Feb 2006 16:32:01 -0800 (PST) Jim Reisert AD1C <[EMAIL PROTECTED]> writes: > I am trying to set up an Orion ("Classic") for FSK. When the Orion > is in "FSK" mode, DX4WIN tells me the mode is "PACK". How do I make > the mode RTTY automatically? Is this a problem with the rig > driver? > > Thanks - Jim > > -- > Jim Reisert AD1C, 7 Charlemont Court, North Chelmsford, MA 01863 > USA +978-251-9933, [EMAIL PROTECTED], http://www.ad1c.us > _______________________________________________ > Dx4win mailing list > Dx4win@mailman.qth.net > http://mailman.qth.net/mailman/listinfo/dx4win > > Duane Calvin, AC5AA Austin, Texas From [EMAIL PROTECTED] Tue Feb 7 22:41:31 2006 From: [EMAIL PROTECTED] (Larry P. Greenberg) Date: Tue Feb 7 22:44:45 2006 Subject: [Dx4win] CW Keying & Radio Interface Message-ID: <[EMAIL PROTECTED]> I have a laptop connected to a Ten-Tec Omni Vi Plus through a serial cable. Can I also key my radio through the same serial port. I noted in the Ten-Tec manual that radio control is done through serial port pins 2 and 3 plus the ground on pin 7. The serial port CW keying interface using a resistor and a 2N2222 only connects to pin 20 (DTR) and pin 7, the ground. Has anybody tried this? Larry P. Greenberg WA9MAG From [EMAIL PROTECTED] Wed Feb 8 00:27:29 2006 From: [EMAIL PROTECTED] (Ted Huddle) Date: Wed Feb 8 02:12:22 2006 Subject: [Dx4win] 7800 Rig file Message-ID: <[EMAIL PROTECTED]> All, Attached is a rig file for the Icom 7800. Put it in the "radios" folder and it will show up in the pull down for available rigs. It runs at the default address of 6A and at 9600 bps. 73, Ted W4CID
