I had no problems with TX0DX importing from 2002 to 2003, it properly showed FK/C as the Entity. Perhaps the problem was you didn't have the path set to the old DXBase location so it could read your call mapping. This is set in the actual import screen just below the path to the new DXB 2003 .mdb file.
I installed 2003 on a different PC than the one I used for 2002. Afterward I compared my statistics and they were exactly the same. I did get an error when I tried to launch 2003 immediately after the installation. Actually it came up as a double error (2 Error messages at the same time) - something about MSVCIRT.DLL being linked to missing MSVCRT.DLL. I checked and both files were in \windows\system subdirectory. I cleared the problem by re-booting the machine (Windows 98SE). I normally reboot after installing software but since the installation asked me if I wanted to launch, I chose to launch - but nothing happened. So I closed the installation screen and tried to start the program and it would not run until I rebooted - strange. Before rebooting, I installed the Non-DXbase Import fix off the website but I don't think that had anything to do with the initial problem. 73, Don AA5AU ----- Original Message ----- From: "Jack" <[EMAIL PROTECTED]> To: "FireBrick" <[EMAIL PROTECTED]>; "Bill Hunstein" <[EMAIL PROTECTED]>; "Dxbase" <[email protected]> Sent: Sunday, May 19, 2002 7:07 PM Subject: Re: [DXBase] TX0DX Import in 2003 > Just add a callsign map of TX0DX with a prefix of FK/C in the callsign > mapping table, then the QSOs in question will import fine. > > Regards, > Jack > > ----- Original Message ----- > From: "FireBrick" <[EMAIL PROTECTED]> > To: "Bill Hunstein" <[EMAIL PROTECTED]>; "Dxbase" <[email protected]> > Sent: Sunday, May 19, 2002 1:40 PM > Subject: Re: [DXBase] TX0DX Import in 2003 > > > > Bill > > I think you need to add Chesterton Island to the countries list. > > before you try to import. > > > > Maybe someone can post the info on how to add Chesterton on the reflector > > for you. > > I have it somewhere but can't find it right now. But will keep looking. > > > > ----- Original Message ----- > > From: "Bill Hunstein" <[EMAIL PROTECTED]> > > To: "Dxbase" <[email protected]> > > Sent: Saturday, May 18, 2002 2:13 PM > > Subject: [DXBase] TX0DX Import in 2003 > > > > > > > All 16k of my log imported fine except the TX0DX and all 6 of them did > not > > > import. It said bad prefix or ERROR: Prefix? > > > > > > Any ideas? > > > > > > Thanks, Bill > > > > > > > > > _________________________________________ > > > Bill Hunstein > > > ICQ#: 134868 > > > _________________________________________ > > > > > > _______________________________________________ > > > DXBase Reflector - Please visit us on the web at www.dxbase.com > > > - - - - - - - - - - - - - - - - - - - - - - - > > > To UNSUBSCRIBE please visit: > > > http://mailman.qth.net/mailman/listinfo/dxbase > > > > > > > > > > > > _______________________________________________ > > DXBase Reflector - Please visit us on the web at www.dxbase.com > > - - - - - - - - - - - - - - - - - - - - - - - > > To UNSUBSCRIBE please visit: > > http://mailman.qth.net/mailman/listinfo/dxbase > > > > > _______________________________________________ > DXBase Reflector - Please visit us on the web at www.dxbase.com > - - - - - - - - - - - - - - - - - - - - - - - > To UNSUBSCRIBE please visit: > http://mailman.qth.net/mailman/listinfo/dxbase >
