Just a little update:
I did a test with pppoe over an ethernet modem, it worked without a
problem. So I know my PPP is alright.
I upgraded the kernel to 2.4.28, exactly the same issue. Only thing I
can think of is I am missing some kernel option but I have the options
from the FAQ.
eciadsl-doctor runs fine up un till it tried ppp and comes up with an
error: 'Failed to set PPP kernel option flags: Incompatible ioctl for
device.' However when I do ifup ppp0 I just get LCP timeout.
Anyone got any ideas?
Thanks,
Matthew Enger
[EMAIL PROTECTED]
On Wed, 2004-12-29 at 22:41, Matthew Enger wrote:
> Hello,
>
> I am trying to get eci working with a Dlink DSL-200 Rev B1. I have had
> lots of previous success with this model and the modem I have is from a
> working installation.
>
> The difference this time, instead of using a redhat/fedora kernel, I am
> using my own kernel as I am booting from compact flash (plan 2.4.27). I
> have checked and rechecked that I have got all the options I need listed
> in the FAQ for the kernel, the interface synchronizes but pppoe can not
> establish:
>
> Dec 29 09:32:37 fredo pppd[18381]: Connect: ppp0 <--> /dev/pts/2
> Dec 29 09:32:38 fredo pppd[18381]: sent [LCP ConfReq id=0x1 <mru 1492>
> <magic 0xd36ca26a>]
> Dec 29 09:33:06 fredo last message repeated 9 times
> Dec 29 09:33:09 fredo pppd[18381]: LCP: timeout sending Config-Requests
> Dec 29 09:33:09 fredo pppd[18381]: Connection terminated.
> Dec 29 09:33:09 fredo pppd[18381]: Waiting for 1 child processes...
> Dec 29 09:33:09 fredo pppd[18381]: script /usr/sbin/pppoe -p
> /var/run/pppoe-adsl.pid.pppoe -I tap0 -T 80 -U -m 1412 -D yes-0, pid
> 18383
> Dec 29 09:33:12 fredo pppoe[18383]: Timeout waiting for PADO packets
> Dec 29 09:33:12 fredo pppd[18381]: Script /usr/sbin/pppoe -p
> /var/run/pppoe-adsl.pid.pppoe -I tap0 -T 80 -U -m 1412 -D yes-0
> finished (pid 18383), status = 0x1
> Dec 29 09:33:12 fredo pppd[18381]: Exit.
>
>
> When I do an ifconfig, I see this:
>
> tap0 Link encap:Ethernet HWaddr 00:FF:AE:23:7A:F6
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:1000
> RX bytes:0 (0.0 b) TX bytes:96 (96.0 b)
>
> Anyone have any ideas?
>
> I have put up further information which may be helpful (rather then
> flood the list):
> http://www.enger.org/eci/eciadsl-pppoeci.log.gz
> http://www.enger.org/eci/kernel-config
>
> eciadsl.conf:
> VID1=2001
> PID1=5100
> VID2=2001
> PID2=5100
> MODE=LLC_SNAP_RFC1483_BRIDGED_ETH_NO_FCS
> VCI=35
> VPI=8
> FIRMWARE=/etc/eciadsl/firmware00.bin
> SYNCH=/etc/eciadsl/gs7470_synch04.bin
> PPPD_USER=test
> PPPD_PASSWD=
> USE_DHCP=no
> USE_STATICIP=no
> STATICIP=
> GATEWAY=
> MODEM=D-Link DSL200 rev B1
> PROVIDER=AU..iiNet
> DNS1=203.14.168.3
> DNS2=203.59.24.3
> MODEM_CHIPSET=GS7470
> SYNCH_ALTIFACE=5
> PPPOECI_ALTIFACE=1
>
> If anyone can help, I would really appreciate it, I am stuck.
>
> Regards,
> Matthew Enger
> [EMAIL PROTECTED]
>
>
>
> =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
> Driver Linux pour modem ECI ADSL USB: http://eciadsl.flashtux.org
> Archives de cette liste de diffusion: http://liste.eci.free.fr
> Pour se desinscrire: mailto:[EMAIL PROTECTED]
>
>
>
>
>
>
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
Driver Linux pour modem ECI ADSL USB: http://eciadsl.flashtux.org
Archives de cette liste de diffusion: http://liste.eci.free.fr
Pour se desinscrire: mailto:[EMAIL PROTECTED]
