Why don't you just write the PO# out to a global variable when you encounter it and then use it at will wherever you want from then on out?
On start of doc PO = ""; and again on start of HL = "O" loop PO = ""; When you encounter po# then PO = #fieldwhereIfoundPO Then when you need to use it #tempPOnum = PO; Make sure you set it to blank at the beginning of next HL = "O" loop etc so you don't mix them up On Aug 21, 2013, at 11:10 AM, Carlos wrote: > Hello all, > > Wondering if any of you could help me out here. I have the below on a > Extended Rule On End, In my HL Loop Item Group. My problem is the 2nd IF - > What I want to do is check to see if the Element isn't there if So then grab > m y PO# from the REF Segment on the Order HL Loop. > > I normally ask my TPs to send me the PO# on the Item Loop LIN07 and that > works fine if they do - we do this because some do pack mix PO# and I need to > know what is in that pack. But we have those that do not mix the PO# but I > still need to output the detail of the PO# if the send it in the LIN07 im > golden but if them do not I want to capture it from the REF and write it out > on all of my detail lines. any ideas? I hope that I had made any sense here. > > Thanks in Advance Carlos > > IF $1000_HL:4.#0735:4="I" THEN > BEGIN > $TempDetailGroup[HL_S_CNT][HL_O_CNT][HL_T_CNT][HL_I_CNT].#TempPoNum:2 = > $1000_HL:4.#0234:48828; > $TempDetailGroup[HL_S_CNT][HL_O_CNT][HL_P_CNT][HL_I_CNT].#TempPoNum:2 = > $1000_HL:4.#0234:48828; > IF #0234:48828= "" THEN > $TempDetailGroup[HL_S_CNT][HL_O_CNT][HL_P_CNT][HL_I_CNT].#TempPoNum:2 = > $1000_HL:2.#0328:3; > $TempDetailGroup[HL_S_CNT][HL_O_CNT][HL_T_CNT][HL_I_CNT].#TempISBN:2 = > $1000_HL:4.#0234:16276; > $TempDetailGroup[HL_S_CNT][HL_O_CNT][HL_P_CNT][HL_I_CNT].#TempISBN:2 = > $1000_HL:4.#0234:16276; > $TempDetailGroup[HL_S_CNT][HL_O_CNT][HL_T_CNT][HL_I_CNT].#TempPrice:2 = > $1000_HL:4.#0212:5; > $TempDetailGroup[HL_S_CNT][HL_O_CNT][HL_P_CNT][HL_I_CNT].#TempPrice:2 = > $1000_HL:4.#0212:5; > $TempDetailGroup[HL_S_CNT][HL_O_CNT][HL_T_CNT][HL_I_CNT].#TempQTYShipped:2 = > $1000_HL:4.#0382:11; > $TempDetailGroup[HL_S_CNT][HL_O_CNT][HL_P_CNT][HL_I_CNT].#TempQTYShipped:2 = > $1000_HL:4.#0382:11; > HL_I_CNT = HL_I_CNT + 1; > TEMP_CNT_ITEM = TEMP_CNT_ITEM + 1; > END > > [Non-text portions of this message have been removed] ------------------------------------ ... Please use the following Message Identifiers as your subject prefix: <SALES>, <JOBS>, <LIST>, <TECH>, <MISC>, <EVENT>, <OFF-TOPIC> Job postings are welcome, but for job postings or requests for work: <JOBS> IS REQUIRED in the subject line as a prefix.Yahoo! Groups Links <*> To visit your group on the web, go to: http://groups.yahoo.com/group/EDI-L/ <*> Your email settings: Individual Email | Traditional <*> To change settings online go to: http://groups.yahoo.com/group/EDI-L/join (Yahoo! ID required) <*> To change settings via email: edi-l-dig...@yahoogroups.com edi-l-fullfeatu...@yahoogroups.com <*> To unsubscribe from this group, send an email to: edi-l-unsubscr...@yahoogroups.com <*> Your use of Yahoo! Groups is subject to: http://docs.yahoo.com/info/terms/