>> To use APF, make sure CONFIG:DUAL PB is set to APF. (This is the >> default. “NOR” restores the original DUAL PB function.)
Given the value of both APF and Dual PB filters, the "menu dance" to switch between the two is a very big drag. Please provide a way to select either function (I'd suggest "Hold" and "Long Hold" as used with Link/Diversity) without resorting to the CONFIG menu. 73, ... Joe, W4TV On 11/3/2010 4:05 PM, Wayne Burdick wrote: > K3 beta-test firmware revision 4.17 (with DSP rev. 2.65) is now > available. This release includes our new APF (audio peaking filter) > for CW mode, which has been helping K3 field testers work "extreme" > weak DX for the past several days. > > For voice modes, there's a "Fast Monitor" option (TX voice monitor > without the processing delay). Also included is a much-improved TX > Noise Gate. > > See detailed release notes below. > > Please send any questions to k3supp...@elecraft.com. For instructions > on how to load beta firmware, see: > > http://www.elecraft.com/K3/k3_software.htm > > 73, > Wayne > N6KR > > * * * > > MCU 4.17 / DSP 2.65 / FPF 1.14, 11-2-2010 > > NOTE: Be sure to install all firmware files for this release, > including FPF 1.14. Otherwise your menu text will be incorrect. > > * APF (AUDIO PEAKING FILTER) ADDED: APF provides enhanced > copy of weak signals in CW mode, and is especially useful when > signals are at the noise level. The K3’s APF is patterned after > the most successful analog APF implementations, and is equally > effective in user tests. To use APF, make sure CONFIG:DUAL PB > is set to APF. (This is the default. “NOR” restores the original DUAL PB > function.) Then hold DUAL PB to turn APF on/off. A special DSP > graphic display is used to show that APF is in effect. At the time > APF is activated, the regular I.F. SHIFT setting, if any, is “frozen,” > and SHIFT then controls the center pitch of the APF filter in 10-Hz > steps. APF is independent for the main and sub receivers, as well > as for presets I and II. Switching between these two presets is a > convenient way of turning APF on/off quickly. > > * ADDED VOICE TX “FAST MONITOR”: Normally the voice > monitor includes a ~20-ms delay, which is necessary to hear how your > on-air signal will sound (with compression, etc.). If you prefer to not > hear any delay in the voice monitor, set CONFIG:TX MON to FAST. > Note: You’ll still hear the delayed and processed monitor if you > adjust the MIC, CMP, TX EQ or TX GATE settings while transmitting. > > * TX NOISE GATE IMPROVEMENT: The Noise Gate/Downward > Expander for voice modes has smoother response and much > improved performance near the threshold. > > * NARROW AF FILTER IMPROVEMENT: Adjusting SHIFT and > WIDTH when using very narrow DSP filters no longer causes > ‘pop’ artifacts. > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html