Welcome to the brave new world. We are on our way to making the hf spectrum
totally unusable with the proliferation of wireless this, microprocessor that,
a switched-mode power supply in every electronic doodad, a CFL in every socket
and high current stepper motors everywhere else.
For example, Home Depot sells fluorescent fixtures rated "for industrial use
only" because they don't meet residential RFI standards, which begs the
question of what do you do if you live next door to an industrial facility.
After installing some of these in my workshop/garage (using conduit) the RFI
was so bad it interfered with OTA TV (pre-digital). I pointed out to the store
manager that it said "Home" in big letters on the outside of the building and
demanded that they special order ballasts rated for "home" (residential)
service. To their credit, they did, but I had to furnish the labor to change
them out. Needless to say, not to their credit, they're still selling the RFI
generators to everyone else.
They also sold me a Maytag front-loader washing machine that is a horrible RFI
generator. Besides the microprocessor, there is the variable-speed-reversible
motor driving the drum. Same issue that Don has, high-current, fast rise time
pulses transmitted on unshielded wiring without any concern whatsoever about
RFI.
Wa
--- On Wed, 11/10/10, Don Nelson <n...@comcast.net> wrote:
Hi all,
I misspoke earlier this year when I said our new Lennox high efficiency
furnace was not generating any noticeable RFI. Quite to the contrary,
the new Lennox furnace is very rich in RFI energy. One observation is
that the RFI has a very broad spectrum and it's presence is not
noticeable by audio sound alone. However, my S meter noise floor goes up
by 3 or more S units when the furnace is heating the house. The furnace
we have is the Lennox G71MMP, said to be a 95% efficient furnace.
The “reference” antenna that I use is a Cushcraft R7 vertical mounted on
the side of the house. The magnitude of the RFI decreases as I listen on
each higher band. On 40m, the RFI from the furnace is over S9 compared
to baseline noise floor of S6 when the furnace is off. The receiver is a
K3 with a pretty good S meter calibration. The difference from
background noise is on the order of 20 dB on 40m and on 20m. The noise
decreases as I listen on higher bands. What the furnace RFI is on 80m
and 160m are unknown because I do not have a “reference” antenna for
those bands.
There are two variable speed motors in this furnace. One motor blows air
throughout the house. The second motor is the “induction” motor and
delivers outside air into the burn chamber. This induction motor and the
drive circuit are the source of the RFI. The blower motor, when running
alone does not generate noticeable RFI. I have used a clamp-on toroid
with a multi-turn secondary connected to an oscilloscope to sample RF on
various leads emanating from the control board inside the furnace. The
four leads going to the induction motor have significant noise on each
as does a ground wire going to the furnace chassis. The other leads
going elsewhere are quiet. The noise I observe on the induction motor
leads is characterized as fast rise time pulses.
I have tried to engage Lennox in discussions on this RFI problem with
limited success to date. The furnace installer has basically given up
without trying pleading ignorance which is understandable.
I am trying things to mitigate the RFI with limited success so far. I
would very much like to hear what others have done to mitigate their
furnace RFI problems.
Don, N0YE
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
