This is a great service to K3 owners with iGear, Mike -- thanks. I'll put you on the short list for owner's manual update notices.
73, Wayne N6KR ---- http://www.elecraft.com On Nov 24, 2010, at 5:42 PM, Michael Downs <k...@verizon.net> wrote: > If you are a K3 owner/operator, you may be interested in a new iPhone > application. I call it the K3 Micro Manual as it incorporates most of the K3 > Owner's Manual in a handy iPhone format. It is compatible with iPhone (iOS > 3.1.3 and later), iPod Touch and iPad. It has been updated to include the > Owner's Manual Errata, and all firmware changes since the Owner's Manual was > published. Thus, it is current through November 14, 2010. In addition, I have > included operating tips from the Elecraft web site, selected emails from the > Elecraft Reflector, and operating experience. > > If you think you may be interested in this app, it is now available in the > Apple App Store. It is listed under the Reference category. Just search for > "K3 Owners Manual" or "ks7d." I welcome your input on enhancements to this > application, and for your favorite operating tips. I plan updates over time > to this app to keep it current with the latest Elecraft Owner's Manual, and > to add new features. > > Following is the table of contents for the app: > > K3 Micro Manual Table of Contents: > > Overview of Application > Introduction > Key to Symbols > Table of Contents > > Controls and Connectors > Introduction > Primary Controls > Display > Multi-Function Controls > Keypad > Memories > VFOs > RIT/XIT > Rear Panel Connectors > KIO3 Connectors > KXV3 Connectors > > Quick-Start > Introduction > Connections > The Basics > Filter Controls > Voice Modes > CW Mode > Data Modes > VFOs and RIT/XIT > Transmit, ATU and Ant > NB, NR and Notch > SPLIT, BSET and SUB > Memories, Messages and DVR > Menus and Switch Macros > Other Features > > Basic Operation > Fundamentals > Receiver Setup > Reducing Interference > Transmitter Setup > Voice Modes > CW Mode > Data Modes > > Advanced Operation > Text Decode and display > CW-to-DATA > Tuning Aids: CWT and SPOT > Audio Effects (AFX) > Dual Passband CW Filtering > Receive Audio EQ > Transmit Audio EQ > SPLIT and Cross-Mode > Extended Single Sideband (ESSB) > General-Coverage RX > VFO B Alternate Displays > Alarm and Auto Power-On > Using the Sub Receiver > Receive Antenna In/Out > Buffered I.F. Output > Using Transverters > Scanning > > Remote Control > Introduction > Remote-Control Commands > Front-Panel Switch Macros > Remote Power On/Off > Automatic Antenna Control > CW/DATA Terminal Applications > K3 Memory Editor > > Options and Accessories > Introduction > Options and Accessories > > Firmware Upgrades > Introduction > Checking your Firmware Revision > K3 Firmware Self-Test > Forcing a Firmware Download > > Configuration > Introduction > Crystal filter Setup > Option Module Enables > Miscellaneous Setup > > Calibration Procedures > Introduction > Synthesizer > Wattmeter > Transmitter Gain > Reference Oscillator > FP Temp Sensor > PA Temp Sensor > S-Meter and RF Gain > > MAIN Menu Functions > Introduction > AFX MD > ALARM > ... > ANTIVOX > > CONFIG Menu Functions > Introduction > 2 TONE > ADC REF > ... > XVn ADR > > Troubleshooting > Common Symptoms > Parameter Initialization > Module Troubleshooting > Error Message List > > Operating Tips > Introduction > CW/DX Operating Scenario > Using TX TEST > AFX (Audio Effects) > RTTY Operation w/o PC > VFO B Display Modes > Add Text to ANT1/ANT2 > RIT/XIT Techniques > Setup for PSK > QRO/Battery Operation > Adjust ATU L-C Settings > RIT with VFO A Knob > KK7P Explains NR > Menu Help Text > Operating at 500 kHz > FW Load Failure Recovery > Operating in Split Mode > 60 Meter Band Operation > > Firmware Release Notes > Introduction > MCU 4.14/DSP 2.60 > MCU 4.13/DSP 2.60 > MCU 4.12/DSP 2.60 > MCU 4.06/DSP 2.60 > MCU 4.05/DSP 2.60 > MCU 4.03/DSP 2.60 > MCU 3.97/DSP 2.58 > MCU 3.94/DSP 2.54 > MCU 3.84/DSP 2.54 > > Hopefully, I can follow this iPhone version with a version for Android > phones. I need to get an Android phone to test the application on before it > is released. Testing in the emulator is fine, but it must be checked out on > actual hardware before release. > > 73, > Mike ks7d > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html