> What kind of isolation diodes would you suggest? Any switching diode (1N4148, etc.) would be fine.
> Any how should they be connected? As any set to isolation diodes ... two diodes per data line (A,B,C,D) cathodes to the K3, anodes to the RCS-12 and KPA-500. 73, ... Joe, W4TV On 6/15/2011 12:11 AM, Dave Perry wrote: > Joe, > > Yes, I am using the four pins corresponding to Band 0 through Band 3 > plus the pin for ground. The RCS-12 works fine connected directly to the > ACC port on the K3. It also works fine when the KPA500 is connected via > the Y cable. It is just that the KPA500 is not switching bands when > connected with the RCS-12. So your suspicion may be correct. What kind > of isolation diodes would you suggest? Any how should they be connected? > > Thank you. > > Dave, N4QS > > ----- Original Message ----- From: "Joe Subich, W4TV" <li...@subich.com> > To: <elecraft@mailman.qth.net> > Sent: Tuesday, June 14, 2011 10:43 PM > Subject: Re: [Elecraft] KPA500 question > > >> >> You might try isolation diodes between the antenna switch and/or >> KPA and the K3. If the KPA is not band switching with the RCS-12 >> connected, I would suspect the RCS-12 is loading the band data >> lines. >> >> How are you connecting the RCS-12? Are you using the "Yaesu BCD" >> connections? >> >> 73, >> >> ... Joe, W4TV >> >> >> >> On 6/14/2011 11:24 PM, Dave Perry wrote: >>> Gary, >>> >>> Good suggestion. I removed the cable going to the antenna switch and >>> now the K3 and KPA500 appear to talk to one another when changing >>> bands. Pushing a band button on the amp changes the amp and the K3 to >>> the new band. I still cannot get the two power levels to work. I also >>> need to figure out how to get the band switch working with the Y cable. >>> >>> Dave, N4QS >>> ----- Original Message ----- >>> From: Gary Gregory >>> To: Dave Perry >>> Sent: Tuesday, June 14, 2011 10:12 PM >>> Subject: Re: [Elecraft] KPA500 question >>> >>> >>> What bothers me is the amp was not switching bands you said?...If the >>> OPER switch is set then the aux cable should allow you to switch >>> bands either way and the amp should indeed switch bands and indicate >>> that on the LCD. >>> >>> >>> Unfortunately, my FT unit has the original I/O board so I can't >>> verify this for you...sorry >>> >>> >>> remove the antenna switch and try see if that makes any difference. >>> >>> >>> Gary >>> >>> >>> On 15 June 2011 13:02, Dave Perry<n...@comcast.net> wrote: >>> >>> Gary, >>> >>> No, I did not remove any pins on the cable. This is the one supplied >>> by Elecraft and I figured that it would be good to go. I just checked >>> the cable and five pins have been removed. I just removed the Aux >>> Cable from the back of the KPA500 and now the band buttons work on >>> the amp. So it does appear that the Aux Cable is the culprit. >>> >>> Dave >>> ----- Original Message ----- >>> From: Gary Gregory >>> To: Dave Perry >>> Sent: Tuesday, June 14, 2011 9:49 PM >>> Subject: Re: [Elecraft] KPA500 question >>> >>> >>> Do you have PIN 10 removed on the KPA-500 end of the Y cable? >>> >>> >>> Gary >>> >>> >>> On 15 June 2011 12:33, Dave Perry<n...@comcast.net> wrote: >>> >>> My KPA500 sn 70 arrived tonight (factory assembled). It took just a >>> few minutes to hook up and get it on the air. I am using the Y cable >>> on the ACC port to split off two cables from the K3 ACC port -- one >>> goes to a new RCS-12 Automatic Antenna Switch and the other goes to >>> the KPA500. >>> >>> I have AUX BUS on the KPA500 menu turned on and Band Change set to >>> normal. If I press a band button on the amp, the K3 changes bands and >>> so does the new antenna switch -- pretty neat. But the band display >>> on the KPA does not change. I have to hit the key and transmit to get >>> the band to change on the KPA500. This does not seem correct. It >>> would seem that pressing any on the band buttons on the amp should >>> change the band on the amp and the frequency display as well. >>> >>> Likewise if I change bands on the K3 or via my logging software, the >>> K3 and antenna switch change bands, but the KPA500 does not. I have >>> to tap the paddle and transmit to get the KPA500 to change to the >>> correct band. I am wondering if there is a problem with the Aux >>> Cable. Any other suggestions? >>> >>> I am up to date on firmware for both the K3 and KPA500. >>> >>> The amp runs very quiet and is silky smooth in full QSK mode. I just >>> need to get the band changing issue resolved. Any help would be >>> appreciated. >>> >>> Thank you. >>> >>> Dave, N4QS >>> ______________________________________________________________ >>> Elecraft mailing list >>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>> Help: http://mailman.qth.net/mmfaq.htm >>> Post: mailto:Elecraft@mailman.qth.net >>> >>> This list hosted by: http://www.qsl.net >>> Please help support this email list: http://www.qsl.net/donate.html >>> >>> >>> >>> >>> -- >>> >>> VK4FD - Motorhome Mobile >>> Elecraft Equipment >>> K3 #679, KPA-500 #018 >>> Living the dream!!! >>> >>> >>> >>> >>> >>> -- >>> >>> VK4FD - Motorhome Mobile >>> Elecraft Equipment >>> K3 #679, KPA-500 #018 >>> Living the dream!!! >>> >>> ______________________________________________________________ >>> Elecraft mailing list >>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>> Help: http://mailman.qth.net/mmfaq.htm >>> Post: mailto:Elecraft@mailman.qth.net >>> >>> This list hosted by: http://www.qsl.net >>> Please help support this email list: http://www.qsl.net/donate.html >>> >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:Elecraft@mailman.qth.net >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html > > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html