Quite right Gary. I have the KAT3 but normally use an external ATU and had forgotten that action.
That assumes you have a setting in memory for that frequency range that produces a decent SWR. If not, HI SWR flashes on the LCD. Ron From: Gary Gregory [mailto:garyvk...@gmail.com] Sent: Saturday, June 25, 2011 2:25 PM To: Ron D'Eau Claire Cc: tomb18; elecraft@mailman.qth.net Subject: Re: [Elecraft] Question about K3: ATU function You will see 'ATU' flash when you TX if the swr is high enough and the ATU will settle on an existing memory. Well at least mine does...:-) Gary On 26 June 2011 06:04, Ron D'Eau Claire <r...@cobi.biz> wrote: The ATU requires you to tell it to tune by tapping the ATU TUNE switch. Keep in mind that a 1:1 SWR is pretty meaningless. You won't see any degradation in your signal if your SWR is 1.5:1 or even 2:1. How far you can QSY before the SWR is an issue depends entirely on your antenna system. The KAT3 ATU retains up to 30 frequencies in each band in memory, so you only need to let it cycle looking for best match once in each frequency range (unless you change your antenna). After that when you tap ATU TUNE it will instantly switch to the memorized settings for that frequency. If you forget to do the initial tune or something in your antenna setup changes, you'll see your SWR is high. Excessive SWR over time will trigger an error message at the K3 - either HIGH SWR or EXCESSIVE CURRENT (since transmitting into poor match will cause the PA current to rise). Tap the ATU TUNE switch to retune. See "Transmit, ATU, and Antenna Controls" in your Owner's manual Quick Start Guide (pg 6 in the Rev 9 manual) for more details. Ron AC7AC -----Original Message----- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of tomb18 Sent: Saturday, June 25, 2011 11:59 AM To: elecraft@mailman.qth.net Subject: [Elecraft] Question about K3: ATU function Hi, Second question: Does one need to press the ATU tune button at each frequency of use? What happens if you forget? Will the K3 automatically try to tune? Thanks -- View this message in context: http://elecraft.365791.n2.nabble.com/Question-about-K3-ATU-function-tp651552 <http://elecraft.365791.n2.nabble.com/Question-about-K3-ATU-function-tp65155 2%0d%0a5p6515525.html> 5p6515525.html Sent from the Elecraft mailing list archive at Nabble.com. ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html -- VK4FD - Motorhome Mobile Elecraft Equipment K3 #679, KPA-500 #018 Living the dream!!! ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html