Thanks Tom, I'm Impressed !!!. Looking forward to the final product.
Adrian .v k4tux From: tom...@videotron.ca [mailto:tom...@videotron.ca] Sent: Friday, 20 April 2012 12:22 PM To: Adrian Subject: Re: RE: [Elecraft] P3 for Windows anyone? [END of Thread] Heres a teaser...recorded with camtasia which slows it down by a factor of 10. It actually runs as fast as the p3 natively. <http://va2fsq.com/wp-content/uploads/2012/04/p3.mp4> http://va2fsq.com/wp-content/uploads/2012/04/p3.mp4 And it works remotely! <http://va2fsq.com/wp-content/uploads/2012/04/p3.mp4> http://va2fsq.com/wp-content/uploads/2012/04/p3.mp4 ----- Original Message ----- From: Adrian <vk4...@bigpond.com> Date: Sunday, April 15, 2012 4:02 am Subject: RE: [Elecraft] P3 for Windows anyone? [END of Thread] To: 'tomb18' <tom...@videotron.ca> > Tom , Ok and well done on an alternative windows controller. 32 > bit would > run fine in either 64bit Win 7 or native 32 bit yes? > Should also run on XP, so I hope you will set top priority to > the 32 bit > ver. Hopefully you can do a Linux version too later. > Please put me on your tester list and feel free to email > whatever you > develop. > If you could set a settings macro per band/mode, that would be > great, such > that a click of that macro would setup what you need. > > Thankyou > > vk4tux at bigpond.com > > -----Original Message----- > From: elecraft-boun...@mailman.qth.net > [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of tomb18 > Sent: Sunday, 15 April 2012 4:32 PM > To: elecraft@mailman.qth.net > Subject: Re: [Elecraft] P3 for Windows anyone? [END of Thread] > > Ok, I have run into a few logistics issues that I hope someone > can assist > with. > In order for the P3 to control the K3 it must maintain > communications via a > serial link. Thus one needs to use a com port sharing > program such as > LP-Bridge or LP-Bridge 2. This works fine within the > design parameters of > the program. As I have not used these programs before, are > there any issues > with them that I should be aware of? Everything is working > fine and far > better than I thought. > > I have found a bug in the P3 firmware: Issuing the #REF command > only allows > setting over -140 to -90 not to +10 as stated in the > manual. This is not > big issue since if you need your reference level at -90 you have other > problems! > > These will be the features in the first version: Please > let me know if I > have missed anything: > Setting of reference level > Setting of Span > Setting of scale > Setting of center frequency > Turning on and off of waterfall > Turning Peak Hold on and off > Turning and setting averaging (waterfall also) Using Markers A > and B by > mouse > 10 customizable function keys: Can set span, or almost anything > that the P3 > can do. Each key can contain many commands at the same time. > Screen capture > Spectrum recording (there may or may not be compression in the first > release..) > Fully scalable spectrum display from 640x400 to 1920x1080 > > I will also have a "remote" mode. Now I would appreciate > peoples feedback > on this. You will need to do a remote login such as using > mstsc or Logmein > etc. Of course, if you did this at full resolution you > will need huge > bandwidth. Most upload speeds for the Internet are around > 1mb/s. Therefore > I will offer a reduced resolution and video update mode. > Perhaps something > like 640x400 and 10 fps.Can anyone suggest another way to do this? > > Well that's it for now. I expect I will have something for > release in a > couple of weeks. The first release will be for Windows 7 > x64. I will try > for the x32 as well. > > I would appreciate any feedback. > Thanks, Tom VA2FSQ > > > -- > View this message in context: > http://elecraft.365791.n2.nabble.com/P3-for-Windows-anyone- > tp7447888p7467230.html > Sent from the Elecraft mailing list archive at Nabble.com. > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html