Hi Jorge, Much of this depends on the sensitivity of the recording device. LIN OUT can be set from 0 to 100. If I remember correctly, a setting of 50 would be a standard line level if the termination is correct - something like 1k ohms. Standard line level is 1Vp-p. I'm not sure what Wayne used though.
I agree with Don on this. Should be fine. 73, matt W6NIA On Sun, 03 Jun 2012 20:15:38 -0400, you wrote: >Jorge, > >I don't think that Line Out setting will be any problem at all. >Normally Line out is not used for SSB or CW operation, but if you are >getting into data modes, it may need to be adjusted. > >73, >Don W3FPR > >On 6/3/2012 6:43 PM, Jorge Diez - CX6VM wrote: >> Thanks Matt and Don for all the help about that. >> >> I went to the station this afternoon to test the cables again. >> >> All seems good now again. I have audio from both K3 and TS850. >> >> Anyway TS850 audio level in the recorded file is higher. >> >> I increased the LIN OUT level and seems I am comfortable with LIN OUT = 30 >> to have a decent audio on the recorded file >> >> This will be a problem during CW or SSB operation? I think not, but just to >> be sure. >> >> Thanks, >> Jorge >> CX6VM/CW5W >> >> -----Mensaje original----- >> De: Matt Zilmer [mailto:mzil...@verizon.net] >> Enviado el: sábado, 02 de junio de 2012 19:45 >> Para: Jorge Diez - CX6VM >> CC: elecraft@mailman.qth.net >> Asunto: Re: [Elecraft] recording from LINE OUT >> >> Jorge, >> >> That *should* work fine. A Line Out level of 10 is what I use here for >> receive audio on data modes like MT63, Olivia, etc. >> >> Make sure you're using a stereo patch cord from the K3 to the input to the >> recording device. >> >> 73, >> matt W6NIA >> >> On Sat, 02 Jun 2012 18:12:07 -0300, you wrote: >> >>> Hello, >>> >>> >>> >>> I trying to record from K3 to recallpro but no audible audio in the >>> recorded file >>> >>> >>> >>> I have LIN OUT = 10 >>> >>> >>> >>> I something else to take care? For example MIC SEL and LIC+LIN settings? >>> >>> >>> >>> Some months ago I recorded and I had a good audio files with clear RX >>> and TX audio, but now I couldn´t. >>> >>> >>> >>> I am recording also from a TS850 and the audio is OK in the recorded file. >>> >>> >>> >>> Thanks, >>> >>> Jorge >>> >>> CX6VM/CW5W >>> >>> >>> >>> >>> >>> ______________________________________________________________ >>> Elecraft mailing list >>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>> Help: http://mailman.qth.net/mmfaq.htm >>> Post: mailto:Elecraft@mailman.qth.net >>> >>> This list hosted by: http://www.qsl.net Please help support this email >>> list: http://www.qsl.net/donate.html >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:Elecraft@mailman.qth.net >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> >______________________________________________________________ >Elecraft mailing list >Home: http://mailman.qth.net/mailman/listinfo/elecraft >Help: http://mailman.qth.net/mmfaq.htm >Post: mailto:Elecraft@mailman.qth.net > >This list hosted by: http://www.qsl.net >Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
