A note for Windows users of Fldigi and the KX3. The version of Hamlib, compiled into Fldigi (for Windows) is not always the latest version as found on the Hamlib project pages.
You can find out what version it is using, with "Help, Build Info" and scroll down to "libraries". You also CANNOT (sory to shout) just download/install a later version of the Hamlib DLL, or build one from source on Windows(Cygwin) and expect Fldigi(on Windows) to use it. It will not, it cannot link to, or use a later external file. The program is not built that way on Windows. (The Linux version does allow you to do that, as it uses whatever is installed elsewhere on the system, and that too can sometimes cause confusion for some.) If what rig control facilities already built into Fldigi will not work for you, try creating a new XML file for Fldigi's RigCAT function, but base it on an existing Elecraft file, that should get you close for starters. You can edit/save/create XML files with Windows Notepad just fine. There is an existing K3 file already in there:- http://www.w1hkj.com/xmlarchives.html That should be at a guess, close to what is needed already. You only realy need frequency control/readback, and mode control/readback (remember to go for DATA A(?) mode ('MD 6' CAT command I think) to disable any RX/TX compression/equalisation settings you use for voice modes.) Also set the filters for something like 100Hz to 3kHz, and use TX/RX control by CAT command, as the KX3 supports that. There almost certainly will be other details to figure out and fine tune, but that's the basics's covered. You will need however, knowledge of the commands and parameters used by the K3/KX3 (or whatever rig you have) they are all in the programmers reference manual, freely downloadable from Elecraft:- http://www.elecraft.com/manual/K3&KX3%20Pgmrs%20Ref,%20E6.pdf (Yes, that link does work, I just checked it.) And idealy a dumb terminal emulator to experiment with. The KX3Util program can be used for that, if you don't have such a tool already. It can all be done, it is not dificult, but can be time consuming (Warning. It can be adictive too!) Also read the comments in the FldigiWiki (google for it!) https://fedorahosted.org/fldigi/wiki/Documentation/HOWTO Especially the "Taming the Wild COMport in Windows" item under:- "I/O Device Naming" It is all possible, you just have to search and read how. I have a KX3, am a long time user of Fldigi on Windows and Linux, and have created the Kenwood TS-870s.xml file, so when I get time(?) I will do this (also in Flrig, one day, unless someone less rusty at C/C++ gets there before me) but in the mean time feel free to create one yourself. You may find it a lot easier than you imagine. Plus, the grin factor at the end when *You* made it all work, is well worth it. Just post the result back to the Fldigi list (and here) for all to revel in your new found expertise. It's all open source after all, the idea being that the "community" contributes and all benefit. There is lots of help on the WinFldigi list (on Yahoo) too if you ask. Get stuck in, and Enjoy! 73. Dave G0WBX. On 23 Jul 2013 at 12:00, elecraft-requ...@mailman.qth.net wrote: > Message: 21 > Date: Tue, 23 Jul 2013 06:36:07 -0500 > From: Nate Bargmann <n...@n0nb.us> > To: elecraft@mailman.qth.net > Subject: Re: [Elecraft] [KX3} rig control with fldigi > Message-ID: <20130723113607.gs27...@n0nb.us> > Content-Type: text/plain; charset=us-ascii > > * On 2013 22 Jul 21:57 -0500, Mike WA8BXN wrote: > > I have found the solution to my problem. First, when the initialize > > button is pressed an error message appeared on the bottom of the > > main window, not on the configuration window that pops up. It took > > me a while to see that. I am using the hamlib option to control the > > KX3. It seems the com port number cannot be bigger than 9 for it to > > work. My Elecraft USB cable defaulted to a com port greater than 9, > > so it did not work. Going to device manager for that com port, one > > can change to com port number, in my case I changed it to com2 and > > it works fine now. > > Hi Mike, et. al. > > The latest version of Fldigi that is in testing (I'm not exactly sure, > ask Dave, W1HKJ, for which version of Fldigi this change affects) > includes the latest version of Hamlib where the COM9+ limitation > should be removed. > > If there are issues with the KX3 Hamlib support, please let me know. > > 73, de Nate >> > > -- > > "The optimist proclaims that we live in the best of all > possible worlds. The pessimist fears this is true." > > Ham radio, Linux, bikes, and more: http://www.n0nb.us ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
