Hi, Still no luck at all. The two jumpers are set as follows: The jumper near the pots is set to EL (both posts covered). The Jumper set at the left of the board is set to IC as per the manual
The RJ45 is plugged in the back. The Heil proset headphones are plugged in the front headphone jack on the K3, the mic is plugged via the foster to the RJ45 cable in rear. The audio that I hear through the headset is fine. If I try VOX, nothing happens(it is set) . If I press XMIT on the transmitter , the transmitter goes into transmit and I try to talk no audio output from the MIC and no RF going out. While the microham is sitting there, the lights on it are Line is red. \When I press a string to be transmitted in DM780, the PTT2 comes on and the SC light comes on. But I do not hear a signal. The elecraft K3 "Mic" is set RPl. Clicking on the sound card in Microham I select Headset Earphone(microham Coded) for Wave Out Line (Microham CODEC Mixer Line. (Microham Codex If I press Test in this window K3 goes into transmit, Line stays red PTT2 comes on SC comes on and Front panel says playing. I hear nothing though just silence. If I adjust everything associated with the microham to max in the mixers, I never hear anything on any of the test modes. I'm at a loss here. Is it sure that the microham cables LINE IN plus into LINE IN on the K3? If I plug the mic in the from panel of the microham there is no difference. Slow going here. Thanks for any hjelp Same thing if I try DM780, sending a On 12/26/13, "Joe Subich, W4TV" <li...@subich.com> wrote: > > >Pi am using a Heil preset as received from Elecraft. I have the k3 > >front mic cable. I have the wire marked line in on the cable to the > >line in on the radio. Same for line out. I have set jumpers to non > >electret. Can someone tell me what I am doing wrong.? > > Elecraft ProSet has an ELECTRET mic you need to set the jumpers in > MKII for electret in order to supply the necessary power to the mic > element and then perform the audio level set-up as documented in the > MKII Users Manual. > > > 73, > > ... Joe, W4TV > > > On 12/26/2013 12:37 PM, Tom wrote: > >Hi, I just hooked up my Microkeyer 2 installed all software and the > >software is communicating with the radio. However if I talk into my > >Mike there is no transmit occurring via Vox or PTT on the radio. Pi > >am using a Heil preset as received from Elecraft. I have the k3 front > >mic cable. I have the wire marked line in on the cable to the line in > >on the radio. Same for line out. I have set jumpers to non electret. > >Can someone tell me what I am doing wrong.? Thanks > > > > > >______________________________________________________________ > >Elecraft mailing list Home: > >http://mailman.qth.net/mailman/listinfo/elecraft Help: > >http://mailman.qth.net/mmfaq.htm Post: > >mailto:Elecraft@mailman.qth.net <Elecraft@mailman.qth.net> > > > >This list hosted by: http://www.qsl.net Please help support this > >email list: http://www.qsl.net/donate.html > > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net <Elecraft@mailman.qth.net> > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html