Thank you David! That did it! Strange that it's not in the KX3 manual...
Thanks again and 73,
Ken
On 2015-10-11 3:00 PM, David Anderson wrote:
Ken,
Here is a copy and paste from something I wrote about this previously:
Found this...
* CW-IN-SSB TRANSMIT ADDED: This feature allows you to send CW while
in SSB mode, which can be useful when your SSB signal cannot be copied
due to poor conditions. The other station will hear a tone at your CW
pitch. To enable CW-in-SSB: Locate the CW WGHT menu entry, then tap
‘1’ (PRE) to alternate between “SSW +CW” (enabled) and “SSB –CW”
(disabled). The default is disabled. ImportantNotes: (1) CW-in-SSB
does not yet apply in SPLIT mode. (2) When CW-in-SSB is enabled,
tapping the KEYER/MIC knob toggles between keyer speed and mic
gain rather than between the two transmit metering scales (CMP/ALC and
SWR/RF). The CMP/ALC scale is still shown temporarily whenever CMP or
mic gain are adjusted.
So that is what was causing it. DATA mode allows you to toggle it to
one or the other so when you go back to SSB.
Useful to know.
73
David Anderson GM4JJJ
On 12 Feb 2015, at 20:13, David Anderson <gm4...@yahoo.co.uk
<mailto:gm4...@yahoo.co.uk>> wrote:
Correction I meant stuck displaying CMP ALC in the last sentence.
73
David Anderson GM4JJJ
On 12 Feb 2015, at 20:11, David Anderson <gm4...@yahoo.co.uk
<mailto:gm4...@yahoo.co.uk>> wrote:
We have noticed (others on the Yahoo KX3 group) that if you toggle
to the CMP ALC meter display mode by tapping the Keyer/Mic knob
WHILE IN DATA mode that when you return to SSB mode there is no way
to toggle to SWR RF meter display. Tapping Keyer/Mic or CMP in SSB
then makes no difference, you are stuck forever displaying SWR RF.
I wasn't aware of this until today, but it did cause quite a bit of
confusion.
73
David Anderson GM4JJJ
73
David Anderson GM4JJJ
On 11 Oct 2015, at 19:40, Ken Alexander <k.alexan...@rogers.com
<mailto:k.alexan...@rogers.com>> wrote:
I'm trying to set up my new KX3 to run JT-65. I can't figure out how
to switch the KX3's meter over to the CMP/ALC display to set my audio
level.
The manual is vague on this. It says the display switches to CMP/ALC
when in voice modes. Not in DATA A, and I switched to SSB and not
there either. It still displays SWR/RF in receive and transmit. All
the manual says in the DATA A and AFSK A section is to adjust the mic
gain for 4 to 5 bars of ALC indication. I can't until I can switch
the meter display over.
Any help would be appreciated.
Thanks,
Ken Alexander
VE3HLS
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to gm4...@yahoo.co.uk <mailto:gm4...@yahoo.co.uk>
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com