BINGO! Thank you very much Rich!!!! I knew it had worked before
Microshaft had forced the recent "improvement" on me. Microphone was
ON, but APP access to it was NOT. Very subtle change and that's why I
hadn't figured it out.
All works well now!!!!
Jim - W0EB
------ Original Message ------
From: "Richard Ferch" <ve3...@gmail.com>
To: "Jim Sheldon" <w...@cox.net>
Cc: elecraft@mailman.qth.net
Sent: 6/25/2018 10:39:18 AM
Subject: Re: Re[2]: [Elecraft] FT8 using internal USB sound on the K3S
You mean that in WSJT-X's Settings window under the Audio tab, it won't
let you select the K3S's USB Audio Codec for input or output? That's
not how I read your message, but if that is the case, then you may have
fallen victim to a recent Windows 10 "improvement".
In the Windows 10 Settings window, choose Privacy. Then on the left
side, choose Microphone. A setting called "Let apps use my microphone"
should appear. Turn this to On. If this is the problem, turning this
option to On should permit WSJT-X to get access to the sound card
again.
73,
Rich VE3KI
On Mon, Jun 25, 2018 at 11:27 AM, Jim Sheldon <w...@cox.net> wrote:
Nope, it's in DATA A. WSJT-X's CAT control works fine with the K3S,
setting frequency and DATA mode to DATA A (I forgot to mention that,
sorry). The problem has NO relation to the filter controls or any of
the other stuff.
Thanks Rich, but I already have WSJT-X set up the way you suggest
except I never touch the equalizations. I've found in the past that
it only distorts the signal.
The problem as I have stated twice now is WSJT-X can't open the audio
device. Windows 10's device manager reports it is working properly.
CAT via the same USB connection works properly, reads the K3S
frequency, sets the mode to DATA A as it should, test CAT and test PTT
work as they should. Just no audio input from the K3S. I have NOT
tried TX audio to the K3S and won't until I get the audio input
working in receive first.
Thanks,
Jim - W0EB
------ Original Message ------
From: "Richard Ferch" <ve3...@gmail.com>
To: elecraft@mailman.qth.net
Sent: 6/25/2018 10:16:11 AM
Subject: Re: [Elecraft] FT8 using internal USB sound on the K3S
It sounds as though you are putting the rig into USB mode. I believe
you
would be better off putting the rig into DATA A. Set the rig's mode
to DATA
and the data submode to DATA A. With the rig in DATA A, adjust the
K3's
filter controls to put the Lo-Cut at around 0.20 and the Hi-Cut
around 2.8.
With the rig in DATA A mode, set MIC SEL to LIN (this will not affect
your
microphone setting for voice modes). MIC+LIN will be N/A. Adjust the
MIC
gain control to somewhere above zero, e.g. LIN 5 or so.
In the WSJT-X Settings window under the Radio tab, if you are not
using
some other radio control software such as the DXLab Suite Commander,
then
set the CAT control port to the COM port number that Windows has
assigned
to the K3S's USB serial port. Set the Mode in WSJT-X to either None
or
Data/Pkt - not to USB. For PTT, I prefer to set WSJT-X's PTT method
to VOX
and turn VOX on in the K3, or you can use PTT via CAT. Under Split
Operation, choose either Split or Fake It.
In the WSJT-X Settings window under the Sound tab, select the K3S's
USB
Audio Codec as the soundcard device for both input and output.
Right-click on the Windows speaker icon in the Windows system tray
and
select Playback devices, then select the USB Audio Codec (in the K3S)
and
click on the Properties button. Select the Level tab and adjust the
level
slider so it is in the middle of the range.
While receiving in WSJT-X with WSJT-X's Monitor function on, adjust
the
K3S's LIN OUT level so that band noise alone is enough to bring the
level
indicator on the left side of the WSJT-X window to about 30 dB or so.
When
receiving actual signals, the level thermometer should not turn red;
if it
does, reduce the K3S's LIN OUT level. In the Wide Graph window, you
may
need to adjust the waterfall and spectrum gain and zero controls to
get a
good looking spectrum and waterfall. I don't check Flatten - if you
do,
make sure that the Wide Graph window does not display any frequencies
outside the K3S's filter bandpass.
Now transmitting into a dummy load or a dead band at low power or in
TX
Test mode, put WSJT-X into transmit and adjust the Windows level
slider
and/or the K3's MIC gain control to get 4-5 bars on the K3's ALC
meter.
Once this is adjusted correctly, you should no longer need to adjust
either
of these controls. Use the K3's PWR control to adjust the output
power. Do
not try to control the output power by changing the audio level.
Leave the
Pwr slider on the right side of the WSJT-X window at the top of its
range
and don't change it.
73,
Rich VE3KI
W0EB wrote:
For some reason I can't get WSJT-X to pull the input sound or send
output
sound to the K3S through the USB port. I know I have some K3S
parameter(s)
set wrong, but so far I haven't been able to figure out which ones or
how
to change them.
I had this working before so not sure what I did to change it.
Feel like a total dummy, but at 76, I do forget some things - LOL
Any help would be greatly appreciated.
Jim Sheldon, W0EB
Windows 10 PRO 64bit -I have the USB CODEC in the K3S configured as
sound
in and out in device manager and nothing plugged in to the rear of
the K3S
other than external speakers in the speaker jack - nothing to MIC or
LINE
In or LINE Out.
Menu Settings:
MIC SEL is FP.L
MIC + LIN ON
CONFIG Settings:
KIO3B nor
LIN OUT nor 010
MIC BTN OFF
L --MIX -- R A B
RS232 USB
SPKRS 2
SPKR+PH YES
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
<http://mailman.qth.net/mailman/listinfo/elecraft>
Help: http://mailman.qth.net/mmfaq.htm
<http://mailman.qth.net/mmfaq.htm>
Post: mailto:Elecraft@mailman.qth.net
<mailto:Elecraft@mailman.qth.net>
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to w...@cox.net
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com
