If the specs I gave is the correct one that is. I think it is correct due to the part numbers are the same. Just the 68-88 MHz through me off a little.
Joe AB3JN Sent from my Verizon, Samsung Galaxy smartphone Get Outlook for Android<https://aka.ms/ghei36> ________________________________ From: elecraft-boun...@mailman.qth.net <elecraft-boun...@mailman.qth.net> on behalf of Joseph McIntire <ki4...@msn.com> Sent: Saturday, July 18, 2020 11:57:34 AM To: Elecraft@mailman.qth.net <Elecraft@mailman.qth.net>; donw...@embarqmail.com <donw...@embarqmail.com> Subject: Re: [Elecraft] xv50 Rf parts still has a limited supply of them. Sent from my Verizon, Samsung Galaxy smartphone Get Outlook for Android<https://aka.ms/ghei36> ________________________________ From: elecraft-boun...@mailman.qth.net <elecraft-boun...@mailman.qth.net> on behalf of Joseph McIntire <ki4...@msn.com> Sent: Saturday, July 18, 2020 11:44:00 AM To: Elecraft@mailman.qth.net <Elecraft@mailman.qth.net>; donw...@embarqmail.com <donw...@embarqmail.com> Subject: Re: [Elecraft] xv50 Don I found one online same part number says 68-88 MHz, 30 watt, 12.5 V is that the correct one. Sent from my Verizon, Samsung Galaxy smartphone Get Outlook for Android<https://aka.ms/ghei36> ________________________________ From: elecraft-boun...@mailman.qth.net <elecraft-boun...@mailman.qth.net> on behalf of Joseph McIntire <ki4...@msn.com> Sent: Saturday, July 18, 2020 11:35:47 AM To: Elecraft@mailman.qth.net <Elecraft@mailman.qth.net>; donw...@embarqmail.com <donw...@embarqmail.com> Subject: Re: [Elecraft] xv50 Ok thanks for the info once again don. Joe AB3JN Sent from my Verizon, Samsung Galaxy smartphone Get Outlook for Android<https://aka.ms/ghei36> ________________________________ From: Don Wilhelm <donw...@embarqmail.com> Sent: Saturday, July 18, 2020 11:34:06 AM To: Joseph McIntire <ki4...@msn.com>; Elecraft@mailman.qth.net <Elecraft@mailman.qth.net> Subject: Re: [Elecraft] xv50 Joe, Great that you now have the XV144 now stable. It would appear that the power module has gone "belly up". I don't know if Elecraft has any left (the XV50 was discontinued), but you can check. Also check at RF Parts to see if you can find one. As I recall, that power module was discontinued. 73, Don W3FPR On 7/18/2020 9:50 AM, Joseph McIntire wrote: > The question I have is on the XV50 At first it did not work > I found Q5 to not be biasing. So I replaced it. This kit was partially put > together by my father in law who purchased it before he passed. Then about > ten years later I decided to finish it. But any how when I went to replace Q5 > it looked like two of the legs may have been solder bridged and shorted. > Maybe it as not bad. But I was already unsoldering it and had a new one so I > just went ahead and replaced it. Then it would turn on after that. Then in > the alignment I was not getting voltage at TP5 with the radio keyed. Re > soldered some joint I found that looked suspect and once again cleaned all > the flux from the board. I had voltage at TP5 for a short time. Then it went > away upon investigating I realized I did not have that coax selected at the > coax switch to go to the dummy. So I guess I transmitted into an open ended > coax. Probably SWR way to high. And I probably burned up the power module. > Looking fr > om the front of the Xverter on the third lead toward the rear I have 13 > VDC. On the second one back I get 4.4 VDC when keying. But never get any > worth while at the fourth one back. All I get there is about .011 when > keyed. So IT looks like the power module is getting power and is being keyed > but I am not getting anything out of it. Just hoping for someone to tell me > if this is correct and maybe if I can get this part from Elecraft or not. > > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to ki4...@msn.com ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to ki4...@msn.com ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to ki4...@msn.com ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com