That won't work - the KPA100 must be physically removed to keep the base
K2 from using the KPA100 wattmeter.
73,
Don W3FPR
On 8/8/2021 1:54 PM, Frank Krozel wrote:
Just power the radio, not the PA
-73- Frank KG9H
kg9hfr...@gmail.com <mailto:kg9hfr...@gmail.com>
On Aug 8, 2021, at 12:16 PM, jerry <je...@tr2.com
<mailto:je...@tr2.com>> wrote:
All,
Can I just remove the KPA100 and test the K2 "bare" for current draw?
- Jerry KF6VB
On 2021-08-08 09:49, Don Wilhelm wrote:
Jerry,
Replace diodes D16 and D17 in the KPA100 wattmeter, and things should
settle down.
If you attempted to adjust KPA100 C1 while this condition was present,
balance the wattmeter again, it will change with good diodes
installed.
The diodes are 1N5711 type.
That wattmeter is still used as long as the KPA100 is installed on the
base K2 - reducing the power to less than 12 watts does not take it
out of line.
CAL CUR should be set at 3.5 amperes with the KPA100 installed. That
(and the current display) is the current drawn by only the base K2,
and not to the KPA100.
73,
Don W3FPR
On 8/8/2021 12:24 PM, jerry wrote:
All,
My new QRO K2 behaves a little strangely...
On Tune - it makes 108W on 40M, very nice.
But on 20M it behaves strangely. It won't make more than 20W or
so, complains about high SWR. Even though my Heathkit HM-102
SWR/Wattmeter says the SWR is zilch.
So I moved it to a dummy load. As I turn the power up, it makes up
to about 80W, and then says "Hi CURR". And it claims that the
dummy load ( an 800W "Florida RF" resistor bolted to a large
heatsink ) is 1.6 to 1, which is totally bogus.
OK, there's a null trimmer for the SWR bridge. I got it down to
1-to-1 SWR on 20M. It degrades on higher bands though - up to 1.5
to 1 on 10M.
Now, 20M gives me a max of 45W - above that it complains "HI CUR".
It's doing that on all bands. With the PA off via menu, I get a
maximum of about 8.5W before getting the "HI CUR" message. I tried
setting the current up a little bit on the CAL CUR menu, but no
real difference.
With a clamp-on DC ammeter ( which I don't trust THAT much ) I
see 340mA on receive,
and just about 3.6A when the display goes "HI CUR". This is with
the PA turned off. The
display shows 7W just before this happens. Hmm, 13.8V times 3.5A
means 48.3W DC input. Seems a little excessive.
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
<http://mailman.qth.net/mailman/listinfo/elecraft>
Help: http://mailman.qth.net/mmfaq.htm <http://mailman.qth.net/mmfaq.htm>
Post: mailto:Elecraft@mailman.qth.net <mailto:Elecraft@mailman.qth.net>
This list hosted by: http://www.qsl.net <http://www.qsl.net>
Please help support this email list: http://www.qsl.net/donate.html
<http://www.qsl.net/donate.html>
Message delivered to kg9hfr...@gmail.com <mailto:kg9hfr...@gmail.com>
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com