Yes. 73, Jim N7US
From: Bob Wilson, N6TV <n...@arrl.net> Sent: Sunday, October 31, 2021 17:52 To: Jim McDonald <j...@n7us.net> Cc: j...@kk9a.com; Elecraft Reflector <elecraft@mailman.qth.net> Subject: Re: [Elecraft] Elecraft K-Pod manual updated -- now covers use with the K4 Did you try upgrading the K-POD firmware to 1.12 to use these new features? 1.12 10/20/2021 Holding down F4 on power up selects encoder 1:1 rate. Holding down F5 on power up selects 1:0.5 rate. 73, Bob, N6TV On Sat, Oct 30, 2021 at 8:26 PM Jim McDonald <j...@n7us.net<mailto:j...@n7us.net>> wrote: I have tried all three settings – 100, 200, and 400. The K-Pod tuning rate is half the rate of the K3/K3S. 73, Jim N7US From: Bob Wilson, N6TV <n...@arrl.net<mailto:n...@arrl.net>> Sent: Saturday, October 30, 2021 22:22 To: j...@kk9a.com<mailto:j...@kk9a.com> Cc: Jim McDonald <j...@n7us.net<mailto:j...@n7us.net>>; Elecraft Reflector <elecraft@mailman.qth.net<mailto:elecraft@mailman.qth.net>> Subject: Re: [Elecraft] Elecraft K-Pod manual updated -- now covers use with the K4 What is CONFIG:VFO CTS set to? Did you try changing it? 73, Bob, N6TV On Sat, Oct 30, 2021, 8:06 PM <j...@kk9a.com<mailto:j...@kk9a.com>> wrote: I was just on 40m and my K-Pod VFO is definitely 1/2 the rate of my K3S's VFO. John KK9A -----Original Message----- From: Jim McDonald [mailto:j...@n7us.net<mailto:j...@n7us.net>] Sent: Friday, October 29, 2021 7:19 PM To: Bob Wilson, N6TV; j...@kk9a.com<mailto:j...@kk9a.com>; Elecraft Reflector Subject: RE: [Elecraft] Elecraft K-Pod manual updated -- now covers use with the K4 My K-Pod tune at half the rate of the K3S at all three VFO CTS settings. If Elecraft could do it, I'd like for the K3/K3S F/W to provide the option for the K-Pod to tune at the same rate. 73, Jim N7US -----Original Message----- From: elecraft-boun...@mailman.qth.net<mailto:elecraft-boun...@mailman.qth.net> <elecraft-boun...@mailman.qth.net<mailto:elecraft-boun...@mailman.qth.net>> On Behalf Of Bob Wilson, N6TV Sent: Friday, October 29, 2021 16:59 To: j...@kk9a.com<mailto:j...@kk9a.com>; Elecraft Reflector <elecraft@mailman.qth.net<mailto:elecraft@mailman.qth.net>> Subject: Re: [Elecraft] Elecraft K-Pod manual updated -- now covers use with the K4 In the K3, if you change *CONFIG:VFO CTS*, the VFO frequency moves faster at 400 than at 100 (counts per turn), but the K-POD always tunes at 100 or 200 counts per turn (can't remember which). The K-POD ignores the VFO CTS setting on a K3. In the K4, the equivalent setting is *MENU:VFO Counts per Turn*, and *both* the VFO knob and the K-POD tuning rates are affected equally. Just spin one knob exactly one full 360° turn clockwise, then spin the other knob full turn counterclockwise. If you don't end up back on the frequency where you started, it means the tuning rates are not the same. 73, Bob, N6TV On Fri, Oct 29, 2021 at 11:25 AM Fred <k6dg...@gmail.com<mailto:k6dg...@gmail.com>> wrote: > "... except for the slow tuning." ???? I must be missing something. > My K-Pod tunes at the same rate as the K3. I have one of the K-Pod > buttons emulating the FINE/COARSE button on the radio ... use it all the time. > Maybe the rates I have my K3 configured for just happen to match the > encoder in the K-Pod? > > 73, > > Fred ["Skip"] K6DGW > Sparks NV DM09dn > Washoe County > > j...@kk9a.com<mailto:j...@kk9a.com> wrote on 10/28/2021 8:07 PM: > > I really like the K-POD, except for the slow tuning. Too bad that > > the K3 firmware "cannot" reprogram it. > > > > John KK9A > > > > > > Bob Wilson, N6TV wrote: > > > > Yes, this only works with the K4. The K3 firmware cannot reprogram > > the K-POD encoder to match the K3's tuning rate. > > > > 73, > > Bob, N6TV > > > > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com